-
Product
Mixed Signal Oscilloscope - 350 MHz, 2 Analog Plus 16 Digital Channels
MSOX3032T
Oscilloscope
350 MHz2 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
Mixed Signal Oscilloscope 100 MHz, 4 Analog Plus 16 Digital Channels
MSOX3014G
Oscilloscope
The MSOX3014G 100 MHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Analog Output/Arbitrary Waveform Generator PXI Card
GX1649 Series
Waveform Generator
The GX1649 is a 3U PXI digital to analog output board designed specifically for applications where multiple DC or AC analog outputs are required. The GX1649 offers 64 output channels with 16-bits of precision signal sourcing performance and can be used as a DC source or arbitrary waveform generator.
-
Product
Analog Control Cable for Electronic Loads
EE105T-xx
-
The EE105T pre-wired bias power cable is designed to be used with the EE301xx & EE151xx series electronic loads. The cable allows you to connect the electronic load to a regulated 12Vdc bias power supply for operation of the electronic circuits in the load or by moving a wire use the 15-24 Volts unregulated input
-
Product
Analog Noise Generator
PNG7000
-
The PNG7000A Series instruments generate white Gaussian noise and provide a summing input to control signal-to-noise (SNR) or carrier-to-noise (CNR) for bit-error-ratio (BER) testing. The output can also be used as a source for Jitter applications.
-
-
-
Product
10/30 MS/s, 12-Bit, 4-Ch Simultaneous Analog Input PCI Card
PCI-1714
-
4 single-ended analog input channels12-bit A/D converter, with up to 30 MHz sampling rateMultiple A/D triggering modesOnboard FIFO memory 32,768 samples4 A/D converters simultaneously samplingProgrammable gainProgrammable pacer/counterBoardID™ switchUniversal PCI Bus (supports 3.3 V or 5 V PCI bus signals)
-
Product
Basic Quad J-Type Analog Thermocouple Amplifier
SEN-30103-J1
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
PMC Analog Out Board
MS 1821
-
*Bus Interface:- 32 Bit PCI Bus with PMC Interface*Speed of operation up to 66MHz*Spartan-3AN FPGA based design*32 channel single ended analog Output*Unipolar or bipolar voltage output*Programmable output voltage: 0-5V, 0-10V, 0-10.8V, ±5V, ±10V, ±10.8V and is capable of driving up to +/-20mA*16 bit Resolution*Conversion time 10usec typ*Over current protection*Driver interface for Windows2000/XP/VISTA and LINUX OS*Self Test future
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
8 channel 16 bit Digital to Analog
CPCI-DA8-1
Digital / Analog Converter
The CPCI-DA8 is a slave Digital to Analog board that is managed by the host processor on the CPCI bus. The card contains a state machine that performs mostof the work of outputting data, in order to minimize the impact to the HOST system. The CPCI-DA8 is supported by ALPHI Technology under Windows NT by a Board Support Package which is supplied with the card. Other documentationsupplied with the card will describe this support in full detail.
-
Product
PCIe-5763, 16-Bit, 500 MS/s, 4-Channel PCI FlexRIO Digitizer Device
786163-01
FlexRio Digitizer
The PCIe-5763 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PCIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
I/Q Modulators
-
Analog Devices I/Q modulators and demodulators operate at frequencies up to microwave and feature a combination of high performance, broadband operating frequency, and flexibility.
-
Product
MXG Signal Generators
-
On the path to better performance, the Keysight's MXG signal generators are fine-tuned signal sources in R&D measurements. Whether you’re pushing for a linear RF chain or an optimized link budget, the analog and vector MXG models deliver the performance and capabilities you need: phase noise, ACPR, channel coding, and more.
-
Product
PXIe-7862, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module
786672-01
Multifunction Reconfigurable I/O
PXIe, Kintex-7 325T FPGA, 16-Channel AI, 1 MS/s, PXI Multifunction Reconfigurable I/O Module - The PXIe-7862 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of timing and synchronization. With 16 analog input channels connected directly to a Kintex-7 325T FPGA, you have ample space to design applications that require precise timing such as hardware-in-the-loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe-7862 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe-7862 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
Product
L-Series Kit
ZS-LRLT
-
The L Series units all share a wide tuning range of three standard Lectrosonics blocks, or 67.5 to 76.8 MHz, depending on the specific frequency band, and employ Lectrosonics' patented Digital Hybrid Wireless® technology for compandor-free audio along with compatibility modes for interoperability with older analog systems. Like all our other products, the L Series units are made in the USA and feature machined aluminum housings, user-friendly setup and reliable operation. The ZS-LRLMb kit [or ZS-LRLT kit] makes it easy to put these products right to work on the job. Everything you need is here: transmitter, receiver, mounting hardware, lav mic and connecting cables. Even batteries are included! Check with your Lectrosonics dealer for pricing and availability.
-
Product
Infiniium V-Series Oscilloscope: 25 GHz, 4 Analog Channels
DSOV254A
Oscilloscope
25 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.73 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
Product
PXI-5650, 1.3 GHz RF Signal Generator
779670-00
RF Signal Generator
The PXI‑5650 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXI‑5650 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
PXIe-5651, 3.3 GHz RF Signal Generator
PXIe-5651 / 781216-01
RF Signal Generator
PXIe, 3.3 GHz, PXI RF Analog Signal Generator—The PXIe‑5651 features continuous-wave generation capabilities with FM, 2‑FSK, or OOK modulation. It uses direct digital synthesis (DDS) for high-resolution frequency hopping or phase-continuous sweeping for fixture and device characterization applications. The PXIe‑5651 is ideal for clocking nonstandard sample rates, such as WCDMA signals at baseband or intermediate frequency (IF). With these versatile signal generators, you can perform analog and digital modulation through the onboard DDS circuit, which gives you frequency modulation and frequency-shift keying for applications such as bit error rate test, antenna testing, or even keyless entry. You can also perform amplitude modulation using on-off keying.
-
Product
Analog Output Series Sensors
-
Shanghai Pubang Sensor Co.,Ltd.
1. Measured distance is linear to output signals, high accuracy, can precisely indicate position of tested objects2. With the change of detection distance, itcan provide 0-10V or 4-20mA of standard analog signals; widely used for distance measurement, thickness measurement,etc
-
Product
Signal Level Meter
HT828B
-
Hangzhou Softel Optic Co., Ltd.
The signal level meter, SE828C is able to measure EQ, C/N, V/A and trunk volt in the CATV analog system, the number keys is designed to direct input frequency so that work would be easier. It can measure 2 channels at the same time.
-
Product
PXIe-4463, 51.2 kS/s, 2-Output PXI Sound and Vibration Module
783086-01
Sound and Vibration
The PXIe‑4463 offers high dynamic range and THD+N for audio, acoustic, and vibration applications. It provides the high precision and dynamic range necessary for the most stringent audio generation requirements in a modular form … factor. The PXIe‑4463 contains two 24-bit digital‑to‑analog converters to allow for fully differential simultaneous generation. Complete with three gain ranges, the PXIe‑4463 can generate current with programmable, per channel output configurations. The two timing engines allow you to perform multisample-rate applications on a single module and independently start and stop channels on a single module.
-
Product
4 Channel DAC FMC Module
DACNF04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF04 is a four channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit input and one DC coupled single-end analog output with DC – 250KHz sampling speed based on Linear Technology’s LTC2704-16. The 16-bit input data for each channel is provided through SPI from the FPGA on the FMC carrier board. A single-ended TTL level trigger output is provided from the FPGA.
-
Product
Compact Semiconductor ATE
QST286
-
Qmax Test Technologies Pvt. Ltd.
The Qmax Model QST286 is a compact small foot print, sophisticated automatic semiconductor tester. Its state-of-the-art hardware design which is freely configurable to user's application requirements and software features makes it ideal for high throughput production testing of wide range of low pin count medium power ICs as listed below but not limited to Optocouplers, Isolators, LEDs, Photo diodes, Photo transistors, Photo sensors, Photo detectors , Analog Mux , Relays and more.
-
Product
Scienlab Measurement And Control Module
SL1065B
Communications Module
The Scienlab Measurement & Control Module SL1065B – Analog Input is a rack-mount measuring and control module for measuring voltages and currents (e.g. single cell voltages in battery modules or packs). It features fully galvanically isolated measurement inputs and records all measured values synchronously and with common time stamps by Precision Time Protocol (PTP).
-
Product
ISA Data Acquisition Boards
A-812PG
-
A-812PG is a 12-bit multifunction analog and digital I/O board for PC/AT compatible computers. A-812PG offers 16 single-ended plus two channels of analog output with 12-bit resolution. A-812PG has 16 digital inputs, 16 digital outputs, and one timer/counter channel. A-812PG Provides gains of 1, 2, 4, 8, and 16. It has a maximum sampling rate of 62.5K samples/s. DMA operation is jumper selectable for levels 1 or 3. Interrupts are jumper selectable between 3 and 15.
-
Product
Analog Oscilloscope
PS-605
-
VERT. SENSITIVITY FROM 1mV/DIV TO 15V/DIV. SWEEP RATE FROM 10NS/DIV TO 1S/DIV. COMPONENT TESTER. DELAY SWEEP. CE, TUV GS, UL, CUL, IEC1010.
-
Product
LVDS (Low Voltage Differential Signaling) Drivers and Receivers
-
LVDS (Low Voltage Differential Signaling) Drivers and Receivers from Analog Devices offers designers robust, high speed signaling for single-ended to differential solutions for point-to-point applications. Our selection of products conform to the TIA/EIA-644 LVDS standard and contain the first LVDS transceivers to meet 8 kV IEC ESD performance standards - important for robust, interboard applications where the connectors can be exposed to more harsh electrostatic environments. Companion differential line receivers and differential line drivers support up to 600Mbps. LVDS greatly improves noise immunity and minimizes emissions for high speed point-to-point data transmission and is a low power alternative to emitter-coupled logic (ECL) or positive emitter-coupled logic (PECL) signaling.
-
Product
Manufacturing Defects Analyzer
406A
-
The 406A is designed to target the highest number of assembly failures for the least amount of capital equipment cost, programming time, and maintenance costs. The precision Stimulus Measurement Unit provides AC/DC analog measurements that are accurate, stable, repeatable, and reliable.
