Electromagnetic Interference
unintentional signal interference as a byproduct of normal operation, originating from within the system or circuit. Also known as: EMI
-
Product
Electromagnetic Interference Test
-
Electromagnetic interference (also known as radio frequency interference) tests are used to determine the electromagnetic characteristics of electrical, electronic, and electro-mechanical equipment. Electromagnetic interference, both radiated or conducted, can affect the performance of equipment. Electromagnetic interference tests are specified as follows: conducted emission, radiated emission, conducted susceptibility, and radiated susceptibility.
-
Product
LCR Meter, 1 MHz to 300 M/500 M/1 G/3 GHz
E4982A
LCR Meter
The E4982A LCR Meter provides the best performance for the passive component manufacturing such as SMD inductors and EMI filters, where impedance testing at high frequencies (1 MHz to 300 M/500 M/1 G/3 GHz) is required. Not only for the manufacturing, the E4982A can also be utilized for R&D, quality assurance with the powerful functions such as list measurements.
-
Product
15W to 960W - Single Output
DPP Series
-
*Low Cost*UL 508 Listed*Convection Cooled*Conducted and Radiated EMI, Class B*Input Transient Protection, IEC61000-4*Conforms to EN61000-3-2 (PFC)*Three year warranty
-
Product
Conducted Emission
-
AFJ FFT 3010 & 3030 EMI Receivers have been especially designed for conducted emission measurement, both during EUT diagnostic development and for final compliance testing.
-
Product
VME Bus Repeater
VME-5532L
-
Easily link your VMEbus systems via fiber-optic cable, with total electrical isolation, no EMI generation and high-noise immunity.
-
Product
IC & Transformer
-
Mornsun Guangzhou Science & Technology
MORNSUN launched the self-designed electronic integrated circuits according to the different product lines, types of the integrated circuit include AC/DC power supply control ICs, DC/DC power supply control ICs, interface ICs, start-up ICs, contactor power saving controller ICs and digital isolator ICs. MORNSUN IC chip can be widely used in industrial equipment, process control, data acquisition system, building automation, smart meter, etc. Adopting MORNSUN's AC/DC transformers and DC/DC transformers, with the use of its control ICs, can achieve wide voltage input flyback power supply design with multiple protection functions and superior EMI performance. We hope that those power transformers along with the integrated circuits & chips electronics can be an ideal fit for your application needs.
-
Product
Fast Ethernet SFP Module
SFP-FSM-20K
-
Hardened SFP/155-ED, SM1310/LC 20km(also known as 808-38103) Industrial standard small form-factor pluggable (SFP) package, Provides digital diagnostics monitoring (DDM) functionality, Wide specifications and fiber types available. Comes with metal enclosure for EMI, The Class 1 laser product complies with EN 60825-1.
-
Product
EMI Filter/TVS Arrays
-
ProTek offers TVS protection and EMI Filtering all in one package. These space saving devices are ideal for use in portable electronics such as Cellular Phones, Cellular Phone Accessories, Laptops, and PDAs.
-
Product
DC Power Supply
PW-3063R
-
*Use Toroidal Transformer. Low EMI & High EMS.*Triple output, 0-32V/0-6A X2 and 5V/3A .Max. 400Watts*Tracking operation. Max. output 64V/6A on tracking series or 32V/12A on tracking parallel.*4 display, Green LED shows Voltage and Red LRD shows Current. Easy to read.*Compact design. G.W. 9Kgs only. Easy to handle.*The resolution of PW-3063R as high as 0.1v and 0.01A.*Very low Ripple & Noise, less than 0.4mVrms. Very suit for precise measurement.
-
Product
Signal Conditioning
-
Sensors that are used to collect the data from the environment often don’t produce signal of characteristics optimal for an analog to digital converter (ADC) to translate to digital data. Additionally, these signals can be subject to electromagnetic interference (EMI) that introduces noise, having a negative impact on the reliability of the data. To make this analog input readable for the processing unit and dependable enough to give the desired quality of data the signal has to undergo a process of signal conditioning.
-
Product
Gigabit Ethernet SFP Module
SFP-GSM-40K
-
. Hardened SFP/1250-ED, SM1550/LC 40km (also known as 808-38204) Industrial standard small form-factor pluggable (SFP) package, Provides digital diagnostics monitoring (DDM) functionality. Wide specifications and fiber types available, Comes with metal enclosure for EMI.
-
Product
Power Supplies
CF-400B
-
The CF-series power supply is built with high-quality components for extra long life and maximum system performance along with heavy duty transformers supporting high-end systems. This fanless power supply has a built-in EMI filter for a true no-noise design. The aluminum chassis is built for maximum heat relief to keep the system cool. Combined with a great ventilated structure, you’ll never need a fan. This is a true silent structure that powers your system at 480 watts efficiency.
-
Product
Thermocouple, Insert, ITA, SIM, 8 Pos, 3 Slot (not loaded)
510181111
SIM Insert
Thermocouple, Insert, ITA, SIM, 8 Pos, 3 Slot (not loaded)Compatible with 410130116, ITA, i2 MX, 22 Slot VTAC/SIM Insert, EMI, and XL version 410130133Not loaded. Thermocouple patchcords need to be purchased separately.
-
Product
EMI Testing
-
Independent Testing Laboratories
ITL offers compliance and qualification testing for virtually any type of electronic product or system.
-
Product
Phase Noise Measurement Application
N9068A
-
One-button measurements for analyzing phase noise in frequency domain (log plot) and time domain (spot frequency)Compatible with phase noise measurement personality in Keysight PSA and ESA spectrum analyzers Runs inside the PXA, MXA, EXA signal analyzers and MXE EMI receiver
-
Product
EMC Test Equipment
TDEMI G series
-
TDEMI stands for a novel generation of EMI measurement systems providing real-time analysis and enabling the user to perform high-quality emission measurements in a fractional amount of time compared to conventional EMI receiver technology. Ultra-fast Analog-to-Digital Conversion as well as real-time signal processing allows to emulate the behavior of instruments like oscilloscopes, receivers and spectrum analyzers. Due to the TDEMI's powerful signal processing hardware platform, corresponding to a computation power of approx. 80 conventional. PCs, such measurements are extremely fast in comparison to state of the art solutions.
-
Product
Passive Components
-
Focusing on frequency control products, electromagnetic interference (EMI/RFI) filters, and resistive components (potentiometers/encoders).
-
Product
Linear Amplifiers
LA Series
-
Motion Control Systems'' linear amplifiers are high performance servo controllers that produce very smooth sinusoidal motor currents using a linear amplifier output stage. In combination with a sinusoidally wound MCS brushless motor, the linear amplifier can achieve extremely precise rotational control with less than 1% torque ripple, no acoustic noise and almost undetectable levels of electromagnetic interference. Standard programmable features allow greater design flexibility, easy installation and start-up.
-
Product
3.6 GS/sec Ultra Wideband RF/IF Extreme 1/2 ATR Recorder
Talon RTX 2589
-
- Rugged 1/2 ATR MIL-spec chassis- Designed for harsh mechanical and thermal environments- Environmentally sealed- Internally conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 22 lb (10kg)- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- Capable of recording RF/IF frequencies to 2.8 GHz- Ultra Wideband recording with 3.6 GHz 12-bit A/D- Selectable 1.8 GHz dual channel mode- Up to 61 TB of solid state storage in removable QuickPac- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow API, GUI and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
Product
Fast Ethernet SFP Module
SFP-FSS-20KTX
-
Hardened SFP/155-ED, SS-SM/SC (1310T/1550R) 20Km(also known as 808-38121) Industrial standard small form-factor pluggable (SFP) package, Provides digital diagnostics monitoring (DDM) functionality. Wide specifications and fiber types available, Comes with metal enclosure for EMI.
-
-
Product
ITA, G6x, 9 Module, Removable Backshell, Keying Feature
410104769
ITA
The adaptable G6x ITA integrates a wide variety of I/O options in various module configurations that allow engagement of up to 1,920 signal contacts. The G6x ITA has a removable backshell that also reduces electromagnetic interference.
-
Product
USB Harmonic Comb Injector
J2150A
-
The USB Harmonic Comb Injector is a fast, easy-to-use, ultra-portable signal generator for interrogating your PDN to identify noise sensitivities. Quickly identify power supply related issues. Multiple modes include time and frequency jitter. Wideband harmonic comb spans 1kHz-1GHz+. Great for clock power supply EMI spectrum testing.
-
Product
Current Caliper
KH23101
-
Beijing KeHuan Century EMC Technology Co,.LTD
The KH23101 current caliper is a toroidal transformer used to measure EMI current. When measuring, the caliper does not directly touch the electrical conductor or the cable under test. The conductor passing through the caliper window is used as the single-turn primary wire of the transformer, and the secondary is designed to be multi-turn. Use with 50 Ω receiving system (such as EMI electromagnetic interference field strength meter or spectrum analyzer). In order to facilitate installation and rapid measurement of EMI current, it is designed as a caliper that can be opened.
-
Product
EMI Test Receivers
-
EMI test receivers; extremely accurate instruments designed to detect electromagnetic emissions rigorously, to ensure all emissions conform to the Standard being tested to. Configured to set up running the required tests for parameters defined by the Standards as simply as possible, including automated test routines. R&S EMI test receivers can be much more too, with a full signal and spectrum analyzer in the same instrument.
-
Product
ITA, ICon, EMI-Shielded, With Threaded Coupling Adapter And Protective Cover
410123102
ITA
The iCon EMI has many of the standard features of the iCon, in addition to Electro-Magnetic Interference protection. The EMI shielding effect on the iConEMI ITA is provided by the stainless steel fibers in the removable plastic cover and threaded metal coupling adapter. The opening of the threaded coupling adapter provides clearance for a maximum cable bundle with an oblong bushing effective diameter of 1.37 in. Protective cover included.
-
Product
CATV Measurement Receiver
VAROS 107
-
The VAROS 107 was specially designed for installation and maintenance of cable TV networks. The large high resolution TFT display, the backlit keyboard, the built-in DOCSIS 3.0 and EMI measurement all contribute to making work for the technician easier.
-
Product
Mixed Domain Oscilloscope
3 Series MDO
-
With the largest display in class, improved low-level signal measurement accuracy and industry-leading probe performance, the 3 Series MDO sets a new standard for bench oscilloscopes. Whether you’re testing your baseband design for IoT or just for simple EMI sniffing, the 3 Series has a unique true hardware spectrum analyzer built right in with superior RF test performance and guaranteed RF specifications.
-
Product
ITA, G20, 20 Module, EMI, 2"
410120223
ITA
ITA, G20, 20 Module, 6.75" Series Adapter, EMI, 2"
-
Product
Mounting Flange Kit, G40X, Receiver, Agilent M9019/Adlink PXES-2785
310113801
Mounting Kit
Mounting Flange Kit, G40X, Receiver, Agilent M9019/Adlink PXES-2785.Includes hardware required to mount flanges to the G40X EMI receiver, slide kit and Agilent M9019/Adlink PXES-2785.
