Exposure
-
-
product
Outdoor Exposure Tester
OET
A comprehensive analysis of PV modules includes many different parameters. Determining the normal module operating temperature (NMOT), incidence angle effects and comparing soiling effects on different modules up to the initial degradation of PV modules are all parameters that can be analyzed with our outdoor exposure tester. The tester comes with up to twelve electronic loads installed in a 19" rack. The loads have two main functions: maximum power point tracking (MPPT) and IV curve tracing. For the advanced analysis, it is possible to change between these two modes within one test. In the normal operation mode, the electronic load keeps the module under MPP and each predefined interval an IV curve is traced. The entire tester comes with all necessary sensors such as temperature sensor, which can be attached to the module to determine the NMOT temperature like defined in IEC 61215 (MQT 05) and IEC 61853-2. The irradiation sensor is also included. In combination with our tracking system P2, it is also possible to determine incident angle effects of the PV module. It is also possible to connect other irradiation sensors for diffuse and direct irradiation, which helps to understand the behavior of the module in different irradiation conditions. An optional albedo meter is a powerful tool for the analysis of bifacial modules. The entire graphical user interface is web based and offers the possibility to access the system from the all computers in the network.
-
product
Vibration Exposure Timers
EU Directives and the UK Regulations specify specific daily exposure limits, which can be translated into the HSE's Exposure Points. Points are determined quantifying the Vibration Level of tools and the Time that operators are exposed to the vibration, named Exposure Time.
-
product
Exposure Systems
Model 2012AF & 2012SM
The Model 2012AF Flood Exposure System provides a cost-effective method for automated flood exposure. Designed to accommodate wafers from 8” to 300mm, the tool features automated FOUP loading. Mask and substrate changeover can be accomplished quickly and easily adding to both versatility and high-volume throughput of this production tool.The Model 2012SM Automated Edge-bead Exposure System provides a cost-effective method for edge-bead removal using standard shadow mask technology. Designed to accommodate wafers from 8” to 300mm, the tool features automated FOUP loading. Mask and substrate changeover can be accomplished quickly and easily adding to both versatility and high-volume throughput of this production tool.
-
-
product
EMF Exposure Test
sXcTEM835
Tests radiofrequency electromagnetic field exposures from mobile communication devices operating in the 900 MHz region (additional frequencies upon request). The setup is based on two Crawford TEM cells that are blindly excited by a fully computer-controlled signal unit.
-
product
Long Exposure Time Imaging Cooled CCD Camera
Retiga LUMO
The Retiga LUMO CCD camera is a cooled, 6 megapixel camera that takes advantage of advanced technical features to enable detection and quantification of ultra-low light luminescence signals and for applications that require long exposure times.
-
product
Vehicle Electromagnetic Field Exposure Test System
SEM-400
Beijing KeHuan Century EMC Technology Co,.LTD
Vehicles are our daily public transportation. Electromagnetic pollution in vehicles has attracted more and more public attention. The newly revised compulsory standard GB27630-201X "Passenger Car Air Quality Evaluation Standard" intends to require the electromagnetic field in the car as one of the indicators, according to GB/T37130-2018 "Measurement method of vehicle electromagnetic field relative to human exposure" The measurement method is to measure the intensity of the magnetic field in the car. In the frequency range of 10Hz-400kHz, the electromagnetic field measurement result should meet the public limit requirements of GB8702-2014 for electromagnetic exposure.
-
product
Exposure Level Tester
ELT-400
*Wide frequency range (1 Hz - 400 kHz)*Standard-compliant measurement*Acceptance measurements compliant with CE standard IEC/EN 62233 and Generic Standard IEC 62311*Limit value traces conforming to ICNIRP 1998, 2010 and EMF Directive 2013/35/EU*Real time measurement with RMS and peak detectors*External FFT signal analysis for determining the frequency components via three channel analog output (one channel for each spatial axis) e.g. with the aid of a digital oscilloscope.
-
product
UV Exposure Sources
Standard maintenance, lamp, or filter replacement, does not require any tools. Locking indicator dials on all the system controls, located together for ease of alignment, provide for a reproducible setup. A beam imaging accessory makes alignment even faster.
-
product
High Speed Cameras
MINI SERIES
Three performance level models – Mini AX50, AX100 and AX200 – deliver 1-megapixel image resolution (1024 x 1024 pixels) at frame rates up to 2,000fps, 4,000fps and 6,400fps respectively. All three Mini AX models offer a minimum exposure duration of 1μs as standard with recording memory options up to 32GB providing extended recording times and triggering flexibility. (Sub-microsecond option available on MINI AX200, subject to export approval).
-
product
13MP MIPI Camera Module
e-CAM130_CUMI1820_MOD
e-CAM130_CUMI1820_MOD is a 13MP MIPI Camera Module. This small form factor 13MP camera module comes with S-Mount lens holder. It is based on AR1820HS – an 18MP CMOS Image sensor from Aptina™ / ON Semiconductor® and has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video and the optional MJPEG compression. Though the AR1820HS is an 18MP image sensor, the e-CAM130_CUMI1820_MOD supports only up to 13MP resolution.
-
product
Radiation Meters
A radiation meters is a device designed for measuring varying types of radiation. These devices are portable and are used to inspect personnel, equipment, and facilities for radioactive contamination by measuring the emission of certain radiation particles. They are used to measure external or ambient ionizing radiation field to assess the direct exposure hazard.
-
product
Calibrate Camera RAW Image Files
SpyderCUBE™
Accelerate RAW processing by taking one reference shot under any light condition to set the white balance, exposure, black level and brightness right from the start for your entire series of photos.
-
product
3.4 MP Custom Lens Low Light Camera Module
e-CAM30_CUMI0330_MOD
e-CAM30_CUMI0330_MOD is a high performance, small form factor, 3.4 MP pluggable Low Light Camera Module with S-Mount lens holder. It is based on AR0330 - a 3.4MP CMOS Image sensor from ON Semiconductor®. It has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs the entire Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images, videos and the optional MJPEG compressions.
-
product
Human Vibration Software Modules
Metra Mess- und Frequenztechnik in Radebeul e.K.
*Component of VibroMetra system*Measurement of hand - arm vibrations to EN ISO 5349:2001*One, two or three axes possible*Measuring duration from 1 minute to 1 day *High reliability by user guidance*Good / Bad evaluation of the results*Results are stored in a calculation sheet for the daily exposure A(8) which may include several activities, no external software required, Excel export possible*Offline measurement
-
product
Vibration Meters
Companies must comply with the Control of Vibration at Work Regulations 2005 – this requires them to minimise and monitor exposure to hand-arm vibration and make sure that it does not exceed set levels and cause Hand Arm Vibration Syndrome. The best way to do this is by using a hand-arm vibration meter.
-
product
Control Unit for SITEx & SITExs
SITEX SCU286
The SCU286 has a system for direct measurement of the high voltage delivered by the X-Ray generator to guarantee the accuracy of the radiological parameters. Based on this data the control system maintains the stability of mA and kilovolts to within ± 0.5% in any selection range.SITEX & XS units offer a totally constant quality of exposures, as they are virtually exempt from fluctuations in the power supply.
-
product
External Fire Exposure Test Machine, Battery Safety Testing
Guangdong Bell Experiment Equipment Co.,Ltd
DGBELL external fire exposure test machine is applicable to the standard UL 2580.
-
product
Profiling Belt Radiometer
ILT400
International Light Technologies
The IL400 Profiling Belt Radiometer continues with the all-in-one exposure, intensity, and profiling capability first introduced in the IL393. New solid-state detector and ultra-stable amplifier technology along with rechargability combine to give lower noise, greater speed, and higher accuracy at a price below any precision belt radiometer sold today.
-
product
Xenotest Beta+
FD
Atlas Material Testing Solutions
The Xenotest Beta+ FD is a premium stand-alone rotating rack xenon instrument with a 4000 cm2 exposure area. This instrument is specifically designed to meet the testing needs of the FMCG industry, such as drinks, foodstuffs, personal care and household products. The Beta+ FD enables consumer goods manufacturers to test their products realistically within very short test times, typically with acceleration factors between 10-50 times faster than real time.
-
product
Noise Dosemeter
Castle GA257B
The SONUS Pocket Dosemeters are designed to be powerful and easy to use. These dosemeters are small and tough so measurements and data can be collected throughout the working period. Data can be reviewed on screen or downloaded to a PC for further analysis. The SONUS GA257B is a dedicated basic dosemeter fully compliant with IEC 61252:1993 and IEC 61672-1:2013, giving simultaneous sound exposure (Lep'd) and maximum peak (Zpeak) measurements, an essential feature for Noise at Work Regulations assessments.
-
product
Grypper "Y"
Ironwood Electronics Grypper Y contact is design to work with BGA devices with solder balls/bumps with no equator or small exposure where the standard Grypper cannot reliably hold on to the solder ball. The Y shape, working with the sliding lid, allows reliable contact and ensures device retention in high vibration application. Lower forces, <25 grams, makes insertion easier too and the less aggressive contacting allows 40+ insertions of the same device. The Sliding Lid can be configured to include heat sinking. The Y contact designs cover BGA devices from 0.35mm pitch and larger and the short electrical length has superior electrical performance.
-
product
Software
Blaze
Blaze software is the ideal data analysis and reporting tool for Industrial Hygiene and Safety professionals. From simple, concise compliance reports to powerful detailed data presentations, Blaze excels in supporting various exposure sampling methods and interfaces with the Spark family of personal Noise Dosimeters, the SoundTrack LxT Sound Level Meter and the HVM100 Human Vibration Meter. From instrument setup to presentation-ready reports to exposure record management, Blaze makes noise and vibration exposure monitoring more convenient and productive
-
product
Small InGaAs Camera For Short Exposures
Bobcat Gated Series
The Bobcat 320 Gated series is based on an in-house developed, temperature stabilised InGaAs detector with a 320 x 256 pixel resolution. The Bobcat 320 Gated cameras are able to provide maximum frame rates up to 400 Hz. The exposure time of the sensor is configurable from 100 ns up to 1 ms in steps of 100 ns, or from 1 ms to 40 ms.
-
product
13MP MIPI Camera Module
e-CAM130_CUMI1820_MOD –
e-CAM130_CUMI1820_MOD is a 13MP MIPI Camera Module. This small form factor 13MP camera module comes with S-Mount lens holder. It is based on AR1820HS – an 18MP CMOS Image sensor from Aptina™ / ON Semiconductor® and has a dedicated, high-performance Image Signal Processor chip (ISP) on-board that performs all the Auto functions (Auto White Balance, Auto Exposure control) in addition to complete image signal processing pipeline that provides best-in-class images and video and the optional MJPEG compression. Though the AR1820HS is an 18MP image sensor, the e-CAM130_CUMI1820_MOD supports only up to 13MP resolution.
-
product
2MP Sony STARVIS IMX290 Ultra-low Light Jetson TX2 Camera
E-CAM21_CUTX2
e-CAM21_CUTX2 is a 2MP Ultra-Lowlight 4-lane MIPI CSI-2 camera board for NVIDIA® Jetson TX2 developer kit. This camera is based on 1/2.8" SONY IMX290 CMOS Sensor, one of the most popular Sony's STARVIS® sensor. Its effective pixel back-illuminated technology with improved sensitivity in the visible-light and near infrared light enables customers to capture images even in absolute darkness. This Starlight Camera uses NVIDIA® on-board Jetson TX2 Image Signal Processor (ISP) to perform all the Auto functions (Auto White Balance, Auto Exposure control) and significantly, improved image quality. It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement.
-
product
AutoGet auto Focus Portable Fiber Endface Inspector
CA3008
CA3008 Autoget is an intelligent portable fiber enface inspector. with newest hardware and software, and with functions of auto focus, auto exposure,auto analysis, autogenerate report, auto image transmission, etc. Autoget can clearly find out the defects of fiber endface, such dirts, scratches.
-
product
Linear Array
Linear array sensors consist of a linear array of integrating photosensing pixels which measure incident light over a user-defined exposure time and generate a voltage or digital output which represents the light exposure at each pixel. The sensors are available in a variety of lengths and pixel resolutions. The analog output may be directly interfaced to an ADC for digital processing or for comparing black/white thresholds. Applications include contact image sensing, optical character recognition, edge detection, and object measurement in products such as copiers, document scanners and spectroscopy.
-
product
Power Temperature Cycling
Typically, this test would be selected when during its normal operating activity, the device is subjected to high temperature excursions and is required to power on and off at all temperatures. The power and temperature cycling test will determine the ability of a device to withstand exposure to such temperature extremes with operating biases periodically applied and removed. The worst case conditions expected in a typical; application will be simulated.
