Filter Results By:
Products
Applications
Manufacturers
- Optomistic Products
product
S2 Ultra High Sensitivity Sensors
ULP-S2 UHS
Universal LightProbe S2 Ultra-High Sensitivity Sensors are designed for the test of very dim LEDs, as low as 0.01 mcd minimum, and including very low light-level LED-illuminated action-indicator switches, controls and status indicators for night/dark viewing in automobile interiors. Recommend the use of wide-aperture stainless- steel encased Fiber- optic Probes with contacting tips.Operating temperature range: 0oC to 70oCPower consumption: Operates between +5 and 28 volts D.C., at 6mA max. Less than 4.75 volts is not recommendedVoltage protection: Withstands up to +40 volts, & reverse polarity to -18 voltsSignal Output Loads: 20 mA max. Non-inductive.Output Pins: 3 gold-plated standard wire-wrap pins (0.025 in. sq.)Sensor Size: 0.560 in. dia x 1.38 in. long.Typical response times: <190mSFiber-Optic Probes: Wide-Aperture Fiber-Optic Probe recommendedDesigned for the test of very dim LEDs, as low as 0.01 mcd minimum
-
product
UV Sensors
With analog (4-20mA, 0-5V, 0-10V) or digital (USB, Modbus) output, also available with Android device (incl. app). SiC photodiode chip based Broadband UV sensitivity or filtered for UVA, UVB, UVC or UV-Index spectral sensitivity. Our sensors are also available with logarithmic signal transduction, linearity from 0 … 1500 mV. Calibration services available at our Berlin facility prior to delivery and after use
-
product
UV & WH Meter
Apollo 3.0
Radiometer/photometer measuring UV and visible light via a single wireless sensor. Available as a single kit (1 Reader and 1 Sensor) or double kit (1 Reader and 2 Sensors). Each sensor measures both UV and White Light.
-
product
*Photodiode Energy Sensors
Ophir photodiode laser energy sensors are able to measure low energy pulses down to 10pJ at frequencies up to 20 kHz. Silicon photodiodes for the UV and visible spectrum and Germanium photodiodes for infrared.
-
product
Luminescence Sensors
Luminescence sensors detect visible and non-visible marks that illuminate when using ultraviolet (UV) light. Fluorescent material and marks are reliably detected independently of their pattern, colors or surface conditions on any material. Luminescence sensors emit UV light with a wave length of approximately 375 nm. Fluorescent substances convert the UV light into long-wave visible light, which is then received and evaluated by the luminescence sensor.
-
product
Radiometers / Photometers
Our laboratory-grade PMA-Series PMA2100 and PMA2200 meters can each be used with over 85 of our PMA-Series Sensors, allowing a single meter to serve as aphotometer, a pyranometer or a UV meter simply by changing the sensors! Advanced data logging and software packages are available as well, for total versatility.
-
product
Scientific Cameras
Thorlabs' Scientific-Grade Cameras are specifically designed for microscopy and other demanding applications. The Zelux™ CMOS cameras have small footprints and provide cost-effective solutions for general-purpose imaging applications. Kiralux® cameras have CMOS sensors with high quantum efficiency in a compact housing and are offered in monochrome, color, NIR-enhanced, and polarization-sensitive versions. Our polarization-sensitive CMOS camera is ideal for materials inspection, flaw detection, and other advanced techniques using polarization. The Quantalux® monochrome sCMOS cameras are fast frame rate imagers that combine high dynamic range with extremely low read noise for low-light applications. They are available in either a passively cooled compact housing or a hermetically sealed TE-cooled housing. We also offer scientific CCD cameras with a variety of features, including versions optimized for operation at UV, visible, or NIR wavelengths; fast-frame-rate cameras; TE-cooled or non-cooled housings; and versions with the sensor face plate removed. An intuitive software package, API and SDK for developers, and third-party software support provide options for custom system control and image acquisition.
-
product
Static Control/UV Curing Devices
Panasonic Industrial Devices Sales Company of America
Static Controls (Ionizers)Panasonic offers static elimination tools and Sensors in various form factors, to fit specific application requirements.UV Curing DevicesPanasonic offers LED and lamp spot-type UV Curing Systems. These systems can be controlled manually or integrated into automated applications and configured with replaceable heads, cables and lenses to best fit application requirements.
-
product
UV Sensors
The patented domed shaped sensor head facilitates runoff of dew and rain, helping to keep the detector clean and minimizing errors caused by dust blocking the radiation path. Sensors are housed in a rugged anodized aluminum body and electronics are fully potted.
-
product
UV Meters
OAI’s UV Measurement Instrumentation are the standard for Semiconductor Lithography, MEMS, Sensors, Microfluidics, UV Curing, 3-D Printing, Sterilization, Water Purification and Solar/PVC industries. For over 45 years our meters have earned a reputation for accuracy, repeatability and dependability. We offer full calibration and support services worldwide.
-
-
product
*Pulse Characterization Sensors
Pulse Characterization Sensors provide the ability to see and measure the temporal characteristics of pulsed and CW laser beams. Ophir Fast Photodiode Detectors are designed to convert optical signals into electrical signals which are then measured with third-party instrumentation such as oscilloscopes and spectrum analyzers. Accessories are available to connect to IS6 integrating spheres or fiber optic cables. Attenuating filter accessories are also available to increase their dynamic range. Different models offer silicon, UV enhanced silicon and InGaAs PIN photodiodes, covering a combined spectral range of 193 nm to 1700 nm. Rise times range from 25 picoseconds to 3 nanoseconds. The fast rise times are achieved by an internal reverse bias voltage circuit. Power is supplied by internal batteries and/or an external power supply depending on the model. Detectors should be connected to a 50Ω impedance in order to maintain their nominal rise times. They can be connected to higher impedance loads, but this will result in a significant increase in the rise time. If higher output voltage is required, it is recommended to connect the detector to a trans-impedance amplifier with an Input impedance of 50Ω
-
product
Family of Wavefront Sensors
ShaH
The family of fast, accurate and reliable wavefront sensors. High quality lenslet arrays optimized for reducing the subapereture crosstalk. An interface to a variety of CCD and CMOS sensors allows a wide range of acquisition bands from UV to near IR.
-
product
Laser Power Sensors
Make accurate laser power measurements, from the deep UV to the infrared, with these calibrated, traceable sensors.
-
product
*Irradiance And Dosage Sensors
This sensor family provides cosine corrected irradiance measurement in W/cm² and dosage measurement in J/cm². The sensors are calibrated over their entire spectral range, and are thus ideal for irradiance and dosage measurement of UV, VIS and IR LED based light sources
-
product
UV Calibration
Determination of the angle dependent sensitivity of sensors in use with different UV lamps
-
product
Radiometer/Photometer Kit
AccuMAX™ Series
Single detector with dual sensors measures both ultraviolet and visible light. Complies with ASTM specifications for MPI and FPI. Specially engineered for NDT applications. The AccuMAX XRP-3000 radiometer/photometer kit uses a dualwavelength UV-A/VIS sensor detector to measure both ultraviolet and visible light. Featuring automatic zeroing, integration and signal hold, the unit provides accurate readouts for UV, visible irradiance or radiance.
-
product
UV Meters
USHIO developed a UV meter series to measure intensities of UV radiation. As an add-on, the temperature is also registered. You can decide between the high-end UV meter UIT-250, and UIT-201. The former has a wider measurement range, allows the measurement of energy doses and has the capability to transfer the data via a serial communication protocol to a PC. Various sensors are available. The most popular sensors have center wavelengths at 254 nm, 365 nm or 410 nm.
-
product
Detectors
Thorlabs' photodetectors are capable of detecting light throughout the UV, VIS, NIR, IR, and THz spectral regions. Our photodetectors feature sensors that enable properties such as intensity, power, intensity distribution, wavefront shape, energy, and wavelength to be measured. We offer unmounted photodiodes as well as amplified, biased, and avalanche photodetectors. Thermal power detectors are available unmounted, mounted on a PCB, or mounted on an aluminum plate. Also available are position-detecting sensors, integrating spheres, and an acoustic detection module.
-
product
UV Index Measurement
The sglux UV-Index sensors measure the UVI with a worldwide unique low measurement uncertainty of less than 5 %. This makes our sensors compliant to the highest measurement precisions class one according the DIN/EN 5031-11, chapter 8. Since 2018 our product UV-Cosine_UVI (ERYCA) is appointed for public authority tasks: The German Federal Office for Radiation Protection (BfS) services 27 measurement points in Germany for public information of the daily UV-Index. Twenty of these points (Andernach, Chieming, Duderstadt, Fichtelberg, Genthin, Giessen-Wettenberg, Schauenburg-Kassel, Langen, Lueneburg, Munchen-Neuherberg, Norderney, Belm/Osnabrueck, Schauinsland, Tholey, Todendorf, Waldhof-Falkenstein, Waldmuenchen, Wurmberg, Zingst and Zirchow) use the sglux ERYCA to obtain the local UV-Index value. In 2017 ARPANSA (Australian Government’s primary authority on radiation protection and nuclear safety) began replacing the existing biometers with SiC photodiode UV sensors (sglux ERYCA) at all network sites. There are currently thirteen measurement sites in Australia that have been upgraded to the new sensors.
-
product
UV Analyzer
ARAD-100
The ideal solution for critical UV curing processes where continuous UV monitoring is required to avoid costly downtime and product returns. The built-in sensors are networked for multiple lamp systems with data logging to PC.
-
product
UV systems / UV systems / UV devices
The LightGuide pureUV is a UV radiator part, which prevents direct radiation to the substrate as far as possible.
-
product
UV Measurement
The UV measuring system with the tesa UV Strip and the UV Scan from Hönle is suitable for the reliable testing of the UV dose on the object.
-
product
Integrating Spheres For UV
Konica Minolta Sensing Americas, Inc
Instrument Systems offers complete measurement solutions for UV-A, -B and -C radiation starting from 200 nm. The operation of the well-proven Instrument Systems spectroradiometers, e.g. CAS series, with integrating spheres made from PTFE facilitate high sensitivity measurements of UV radiant flux.
-
product
SiTek UV PSD
The UV PSD is a detector optimized for use in the UV wavelength region 200-400 nm, although its spectral response reaches up to 1100 nm. The sensitivity in the UV region (200-400 nm) is extremely high. The UV-PSD has the same outstanding specifications as the standard SiTek PSD.
-
product
UV Analyzer
AF46
The AF46 is a dual wavelength, high precision UV light absorption analyzer designed for inline operation to provide accurate concentration measurements with remarkable repeatability, linearity and resolution. Wavelength and optical path length can be individually configured to specific requirements for the highest accuracy.
-
-
product
Sensors
YUEQING WINSTON ELECTRIC CO., LTD
Expansion sleeve is a keyless connection device, its principle and use is through the action of high strength tensile bolt, between the inner ring and shaft, between the outer ring and the hub of a huge holding force, in order to achieve the keyless connection between the parts and the shaft.
-
product
Sensors
Chromatic Focus Probe
Measurement of highly reflective, absorbent and transparent materialsMeasuring results are independent of the surface propertiesEspecially suitable for fast and precise measurements on reflective surfaces, lenses, prisms and other optical devicesFlexible probe configurations for highly customized applications
-
product
Sensors
Detect your environment with various sensors. Motion, sound, vision, temperature, and more. 203 products.
-
product
UV Fluorescence SO2 Analyzer
Model N100
Teledyne Advanced Pollution Instrumentation
The Model N100 instrument uses the proven UV-fluorescence principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of low-level Sulfur Dioxide (SO2) gas.
