PCMCIA Interfaces
-
Product
FEC Accelerator Based On Intel® VRAN Dedicated Accelerator ACC100
PCIe-ACC100
Interface Card
ADLINK’s PCIe-ACC100 is a PCIe interface accelerator adapter developed based on Intel's vRAN Dedicated Accelerator ACC100 eASIC chip. It supports 4G and 5G codec acceleration, checksum rate matching, onboard 4G ECC memory, and hybrid automatic repeat request technology (HARQ). The PCIe form factor HHHL (half-height, half-length) can meet the needs of most application scenarios.
-
Product
CAN/LIN Interfaces - 2 Channel PCIe
OTP2 module no053
LIN Interface
Expand your test system with the high-speed interface of the OTP2 module no053. The extension of the module can create new possibilities for your test system.
-
Product
48-Channel DIO (Digital Input/Output) PCMCIA Card
D480C/i(DIOi480)
-
The D480C/i offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
Product
USB-8506 , LIN Interface Device
784664-01
LIN Interface
1- or 2-Port, USB LIN Interface Device—The USB‑8506 is a Local Interconnect Network (LIN) interface for developing applications with the NI‑XNET driver. The USB‑8506 is powered over the USB bus and does not require external power. The USB‑8506 excels in applications requiring logging or manipulation of hundreds of LIN frames and signals, such as in-vehicle data logging, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move LIN frames and signals between the interface and the user program without CPU interrupts, minimize message latency, and free host processor time. The USB‑8506 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Introduction to Graphical User Interface - Softpanel
61800 Series
Interface
The increased demand for Distributed Energy Resource (DR) products such as PV Inverter and Wind Energy systems, have increased the demand for regulation test standards to insure proper operation and safety of on-grid products. Manufacturers testing to prove compliance, need test equipment that can simulate and measure and test their products. Chroma’s 61800 family of Regenerative Grid Simulators provide a full 4 quadrant, regenerative, grid simulation for compliance, safety, and product verification testing
-
Product
Digital/Pattern/PE Card
PA32S
Interface Card
The PA32S represents a new level of performance and capabilities for PXI-based digital instrumentation. Based on the proven architecture of the PE32, the PA32S offers high performance pin electronics and an enhanced timing generator in a compact, 3U PXI form factor. Each card can function as a stand-alone digital subsystem or if required, multiple cards can be interconnected, supporting up to 512 bi-directional pins (16 boards). The PA32S also supports deep pattern memory by offering= 32 M of on-board vector memory with dynamic per pin direction control and with test rates up to 33 MHz. With new 32M capture/log memory, PA32S can capture 32 channels fail log.
-
Product
48-Channel DIO (Digital Input/Output) PCMCIA Card
DIOi480(D480C/i)
-
The DIOi480 offers up to 48 separately controllable Digital I/O lines for general purpose control and monitoring applications.
-
Product
16 GHz Differential Probe with ProLink Interface
DH16-PL
Interface
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
PCI Express Interface Card
MPCIE2-1553
Interface Card
he MPCIE2-1553 is a mini PCI Express Full-Mini Type 2 Interface Card for 1 or 2 MIL-STD-1553 channels in an incredible small package. The MPCIE2-1553 implements the latest MIL-STD-1553 32-bit FPGA Protocol Engine Technology (AltaCore-1553) with the industry leading Multi-Layer Software development software package (AltaAPI).
-
Product
USB-8502, 2-Port, High-Speed/FD, USB CAN Interface Device
784662-01
CAN Interface
1- or 2-Port, High-Speed/FD, USB CAN Interface Device—The USB-8502 is a high-speed controller area network (CAN) interface for developing applications with the NI‑XNET driver. The USB‑8502 is powered over the USB bus and does not require external power. It excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals such as bus monitoring, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex applications. The USB‑8502 is available with a three‑pin COMBICON synchronization connector for triggering and synchronizing the internal hardware timebase with other devices.
-
Product
Portable Avionics Interfaces for USB 3.1
UA2000
Interface
The all-new USB 3.1 design and low-power requirements mean the UA2000 is compatible with USB 2, USB 3, USB 4, and Thunderbolt™ ports. The product ships with both USB-C and USB-A cables for easy connection to current and future computer ports.
-
Product
Interfaces
-
A broad product portfolio of interface technologies that offer lower power consumption, reduced size and ensure the highest performance signal transfer.
-
Product
Interface Probes
-
Low resistance used in: *ICT Testers *Functional Testers *Special Purpose Machines
-
Product
Interface ICs
-
Easy to use, flexible, and reliable. Allegro’s sensor interface ICs offer accurate and fast output for signal conditioning in a wide range of applications, from electric vehicle HVAC systems to transmission oil pressure. Our innovative algorithms deliver robust EMC performance and provide critical diagnosticsthat support automotive safety.
-
Product
*C Series CAN Interface Module
CAN Interface
C Series CAN Interface Modules communicate using onboard transceivers for High-Speed/Flexible Data‑Rate or Low-Speed/Fault Tolerant CAN. C Series CAN Interface Modules are either compatible with NI-XNET or the NI-985x driver, depending on model.Using NI-XNET, you can create applications that require real-time, high-speed manipulation of hundreds of CAN frames and signals. The NI-XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time. C Series CAN Interface Modules work well in applications such as hardware-in-the-loop (HIL) simulation, rapid control prototyping, bus monitoring, and automation control.
-
Product
COM Express Type 7 10GBASE-T Network Adapter Card
10GBASE-T Network Adapter Card
Network Interface Controller
- Supports up to four 10GbE copper interface (10GBASE-T)- Compatible with PICMG COM.0 R3.0 Type 7 modules
-
Product
PCI GPIB (IEEE-488) Interface Card - PCI-GPIB
PCI-GPIB
Interface Card
PCI IEEE-488 interface card (PCI Card for Windows OS)
-
Product
KYK-13 Interface
IP-Crypto
-
The IP Crypto is a special version of the IP-Parallel-HV. The basic design features are retained and an interface to a KYK-13 is provided. The original KYK-13 interface uses the 6.5V reference output, a transfer request output, and 3 inputs for clock, data and switch. The outputs for the general purpose section are reduced to 23 in number. The inputs are all available through the filter or after processing by the KYK-13 interface.
-
Product
Handler/Prober Interfaces
IFXX
-
FETtest offers a variety of Interface options, which expand test capability and provide connection to other production line resources. These interfaces range in complexity from simple handler/prober interfaces to interfaces with user programmable external component connections, to capacitance measurement systems. Models are available to work with the full range of FETtest systems and Remote Stations.
-
Product
NI-9853, CAN Interface Module
780178-01
CAN Interface
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
Product
Interface
-
Interface devices convert one type of control signal to another, saving time and money by extending the life of existing field devices. Please see our Interface Matrix to assist in choosing the correct product.
-
Product
USB-8486, USB, 1-Port, Fieldbus Interface Device
781160-01
Interface Module
The USB‑8486 is a FOUNDATION fieldbus device for developing applications with the NI‑FBUS driver, NI‑FBUS Configurator, and NI‑FBUS Monitor. FOUNDATION fieldbus is a popular industrial communication standard for process control applications. The NI‑FBUS Configurator features user-friendly multi-window interfaces to provide tools for the complete configuration, programming, and execution schedules of FOUNDATION fieldbus segments. The NI‑FBUS Monitor is a stand-alone application used to monitor, debug, and analyze fieldbus data packets.
-
Product
NI-9853, 2-Port, High-Speed C Series CAN Interface Module
779429-01
CAN Interface
2-Port, High-Speed C Series CAN Interface Module—The NI‑9853 is a high-speed Controller Area Network (CAN) interface for developing FPGA-based applications with the NI‑RIO driver on CompactRIO. The NI‑9853 is ideal for low-level FPGA‑based control and triggering applications that are programmed using the LabVIEW FPGA Module. The NI‑9853 is ideal for byte-level manipulation of CAN frames using the LabVIEW FPGA Module. The NI‑9853 is only compatible with CompactRIO systems.
-
Product
SIM Interface
-
Analog Devices’ line of SIM interface parts provide power conversion and level shifting for GSM SIM modules and smart cards.
-
Product
USB-232, 1-Port, USB, RS232 Serial Interface Device
778472-01
Serial Interface
The USB‑232 interface transforms your USB port into a single asynchronous serial port for communication with RS232 devices. You can use a USB‑232 port as a standard serial port from your application, including RTS/CTS hardware handshake lines. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
Interface Solutions
-
The 1394 and AS5643 interface cards define new standardsfor standard OHCI and Extended OHCI host connectivityand set new standards for 1394 and AS5643 data I/O.
-
Product
Interface Pin
-
Smiths Interconnect offers interface probes for all major test equipment manufacturers. We also provide a variety of interface pins for use in test fixtures.
-
Product
Interface Board, 8:1 USB
40-965-903
Interface
Converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 8 USB type A and 1 USB type B connectors. Allows the multiplexing of up to 8 USB1 or USB2 signals.
-
Product
Smartcard Interfaces
-
ST offers complete analog interfaces for asynchronous 1.8 V, 3 V and 5 V smartcards. They can be placed between the card and the microcontroller with only a few external components to perform all supply protection and control functions. Main targeted applications are smartcard readers for set-top boxes, IC card readers for banking, identification and pay TV.
-
Product
Network Interface Card
XMC477RC
Interface Card
The XMC477RC is a quad switched mezzanine card (XMC) compatible module providing a 4-channel Gigabit Ethernet Small Form Factor pluggable (SFP) interface.
