PCMCIA Interfaces
-
Product
Intelligent Interface Card
IIB-1553-VXI-4C
-
The IIB-1553-VXI-4C is an intelligent interface card which provides 4 independent channels for full MIL-STD-1553 test, simulation and bus analysis functions on the VXI bus. All 1553A, 1553B, McAir and STANAG 3838 variants are supported. Each independent channel may be operated as a concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with a windowed Bus Monitor (BM), or as a stand-alone Chronological Bus Monitor (CBM) with comprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. Each channel provides a variable amplitude dual redundant 1553 interface, with 2 Mbytes of dual ported RAM. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
Transponder Panel with GNS/GTN Interface
TA-330XP
-
This transponder panel is layed out to accommodate thecurrent Mode S panel mount units. The transponder caninterface with a GNS or GTN series radio for a morecomplete test of the transponder functions. The panelalso includes altitude, suppression, loop back and thestandard ARINC 429/RS232 interfaces as well. The panelcomes with both a digital voltmeter and ammeter.
-
Product
Power Management & MMI Module
H73000700
Interface
This module, named “6TL-MMI”, is designed to be the interface between an operator and a SYSTEM as well as being a metered power distribution unit (PDU) for it. The module is providing also safety controls, data bus interfaces, temperature control and timers. The 6TL-MMI is suitable for any ATE, and specially for those based on CAN bus controlled devices, because in addition to the above functionalities, this module is also providing galvanic isolation up to 1500V for the CAN bus. This isolation will block potential disturbance towards the DUT.
-
Product
PMC Compatible Wizard Interface
PMC-Wizard
-
The PMC-Wizard is intended for use in ultra high-speed bidirectional point-to-point data transmission systems. The primary application is to provide very high-speed I/O data channels for point-to-point baseband data transmission over controlled impedance media of approximately 50 Ω. The maximum rate and distance of data transfer is dependent upon the attenuation characteristics of the media, and the noise coupling to the environment
-
Product
ICD 3 Test Interface Module
AC164113
-
The Test Interface Board is an aid to isolate application interfacing problems when using the MPLAB ICD 3 (DV164035) as a debugger or programmer. Using the Test Interface Board and running confidence-test options under MPLAB IDE allows testing of the basic functions and signals of an MPLAB ICD 3. The diagnostic results under MPLAB IDE let the user know when the MPLAB ICD 3 is fully functional or if there is a malfunction. The MPLAB Online Help shows the user how to determine possible causes of hardware communication failures with the application.
-
Product
ECU & Bus Interface Modules
ES500
-
ETAS makes the entire software and hardware range available from program development to the calibration of your ECUs. You can use the ETAS tools to address all ECUs that satisfy the ASAM standard. By using these standardized interfaces, our tools are not limited to the ECUs of any particular manufacturer.
-
Product
8 GHz Differential Probe with ProLink Interface
DH08-PL
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
-
Product
Ethernet to GPIB Instrument Interface
Model 8055
-
* Original Ethernet to a GPIB Instrument Interface* Same specifications and user benefits as the Model 9055 above.* 2008 En-Genius Network Product of the Year Award Winner.* Order as a replacement product. New users should order the Model 9055 to get the better performance of our 9000 series products.
-
Product
Systems Analysis Interface
Saint2
-
The Systems Analysis INterface Tool 2, a Delphi Preferred Tool, for Low-cost EOL Testing & Reflashing Without the Need of Additional Hardware.
-
Product
DAS Trays/ Point-of-Interface (POI)
-
*CCI DAS Trays provide a common connection point to the DAS system for multiple BTS's*Modular design allows support for bands from 700MHz to 2700 MHz*Independent level control for each BTS for adjusting TX & RX power*Easy optimization features including separate Uplink and Downlink control*Can support both 0 dBm and +30 dBmDAS TX inputs (high and low power)*Supports NIMO and SIMO configurations
-
Product
Multi-channel Interface Module
PC104E-MA4
Interface Module
Alta Data Technologies’ PC104E-MA4 interface module is a multi-channel, multi-protocol 1553 and ARINC PCI/104-Express interface card supported by the latest software technologies. The PC104E-MA4 card is based on the industry’s most advanced 32-bit FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
Low Profile PCI Express 2-Port RS-232, RS-422, RS-485 Serial Interface
7205e
-
The 7205e low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port utilizes a 16C950 UART with 128-byte Tx/Rx FIFOs that enables data rates to 921.6K bps for reliable high-speed communications in data-intensive applications. This high-performance UART includes 9-bit framing support and is fully software compatible with legacy 16550 applications. In addition, the 14.7456 oscillator and UART’s flexible clock prescalar supports the widest range of standard and non-standard baud rates.
-
Product
I2C High Speed Interface for USB
telos Tracii XL
-
telos EDV Systementwicklung GmbH
Tracii XL is the outstanding I2C Adapter featuring the I2C high-speed specification running the I2C bus with up to 2 Mbit/s. Additionally Tracii XL can work as an I2C monitor.
-
Product
PXIe-SMN Interface Card
-
Avionics Interface Technologies
2.125 Gbps Optical loop networkSingle-mode and Multi-mode optical interfaces supportedUp to 256 Shared Memory Network nodes supportedUp to 200 MByte/sec sustained data ratesMaximum 500 nS latency between nodesNetwork interrupts supportedSoftware Drivers available for Windows (7/8), Linux, LabVIEW Real-Time, and VxWorks
-
Product
GPIB Relay Interfaces
-
*ICS's GPIB to Relay Interfaces provide the user with a choice of 16 contact closures or 16 relay driver outputs for driving external relays. All of the GPIB to Relay Interfaces include 8 isolated digital inputs. Available in ICS's Minibox™ or as an OEM board.*All interfaces are IEEE-488.2 compliant and use SCPI commands for operation with NI or Agilent VISA, LabVIEW and VEE or any GPIB programming language. Use ICS's interactive GPIB Keyboard program for easy operation from your PC without having to write a program.
-
Product
Interface Units
-
intelligent, microprocessor controlled, data acquisition and lambda measurement unit for up to 6 wide band UEGO sensors. It is based on the sensor node and can be used as part of the DATA
-
Product
I2C Fast Mode Interface for USB 2.0, I2C Multimaster and Monitor
Connii MM 2.0
-
telos EDV Systementwicklung GmbH
Connii MM 2.0 is a small, compact, easy-to-use solution for a PC driven I2C transmitter and receiver. The I2C interface works as an I2C multimaster device. Thus, it is able to drive buses running multiple I2C bus masters. Additionally, Connii MM 2.0 is a limited I2C monitor for traffic up to 400kHz.
-
Product
Efficient And Effective Physical Layer (PHY) Testing Of 10/100/1000Base-T Interfaces
-
Explore Sifos Technologies’ highly unique, plug’n play 10/100/1000Base-T Ethernet Physical Layer Testing Solutions. Cost Effective and Comprehensive PHY Testing without Scopes, Fixtures, Probes, and Test Signals.
-
Product
Serial To Digital Interface Boards
-
*ICS's Serial to Digital Interface boards provide the user with digital IO signals that can be user configured to match virtually any application. Both boards are available with high power relay drivers and with optional firmware designed to simplify switching applications.*All boards are designed for mounting inside a chassis.
-
Product
PC/104p Compatible Bi-Directional Serial Data Interface
PC/104p-BiSerial
-
The PC/104p BiSerial has been ported from the PMC BiSerial II. Building on the knowledge and experience gathered from multiple IP and PMC BiSerial implementations and adding in the latest technology has created the PC/104p--BiSerial. The BiSerial features completely isolated FIFOs with 32 bit ports for increased adaptability and performance
-
Product
Reference Grade Expandable Production Interface
Atlas
-
Atlas and Titan are world class multi-track interfaces offering flexible expansion and unsurpassable sonic clarity. Using the latest generation of Prism Sounds trusted conversion, Atlas provides more preamps than Titan making it suitable for a wider range of recording scenarios.
-
Product
Linear Testfixture for VPC iCon i1 Mass Interconnected Cassette Interface (Cassette Not Included) 4 or 10 Positions Blocks, UUT 586 x 248 mm
MG-03-01
-
FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 586 x 248 mm (wxd)• Outer dimensions: 750 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 8 interface blocks of 160 or 170 signals• All interface blocks can be customized
-
Product
Two Port Fibre Channel/MIL-STD-1760E Network Interface Controller
cPCI-HS1760-NCSW-2
-
Avionics Interface Technologies
Integration of Up Fibre Channel and Down Fibre Channel interfaces - Embedded Network Controller (NC) with four priority levels - Two F/AE ports for communication to external devicesInternal four port non‐blocking fabric switch for communication between NC and external devices - Four port non‐blocking Fibre Channel Switch - Meets the requirements of MIL‐STD‐1760E and AS5653 standards - Initialize via the Fast Fabric Initialization (FFI) protocol - ANSI C API enabling complete FC-AE-1553 NC functionality and management - 3U Conduction-cooled Compact PCI module - Designed for extended temperature operations
-
Product
Multichannel ARINC 429 Interface Device
DAS-429UNET/RTx
-
Our DAS-429UNET/RTx is an intelligent, multichannel ARINC 429 interface device that can be connected to any Windows device with a USB or Ethernet connector. It monitors and records all or selected 429 traffic for later analysis or reconstruction in the lab. Exalt is our Windows base graphical tool that allows you to analyze real time or recorded data using many different views: raw data, engineering units or graphical displays.Data can be then extracted from the recorded file, and re-transmitted over the bus to another system in order to see in detail what happened during the recorded test.The combination of a handheld computer, 429Unet card and Exalt provides a complete solution for testing and maintaining ARINC-429 networks.
-
Product
PXIe Remote Control Interface Module with Daisy-Chain Facility
43-921-001
Interface
The 43-921 PCI Express-to-PXI Express expansion kit provides control of PXI Express modules installed in a PXI Express chassis using high bandwidth PCI Express technology. The extension kit can provide up to 4GB/s using PCIe Gen 2 x8 signalling.
-
Product
Ethernet To Parallel Digital Interfaces
-
ICS's 8063 Ethernet Digital Interface provides a fully enclosed parallel interface that is suitable for benchtop or rack mount applications.
-
Product
Advanced ARINC-429 Testing Ethernet Appliance - Parametrics TX Variable Voltage, Digital Signal Generator and RX Signal Capture
ENET-A429P
Ethernet Interface
eNet-A429P™ is an innovative product that provides “remoting” of ARINC operations on 10/100/1000 Ethernet IP/UDP local area networks (LAN). eNet-A429P is a small, low-power, device ideal for details ARINC signal testing with variable voltaqe control of the first 3 TX channels. Alta has combined the industry’s most advanced 32-bit ARINC FPGA protocol engine, AltaCore™, with a real-time IP/UDP thin server. The customer can implement their application with the same feature-rich application programming interface, AltaAPI™, as used with standard cards – often without even recompiling – the utlimate in code portability.
-
Product
RS-232 to RS-422 Interface Converter
Model 63-2SA
-
FEATURES: Full Duplex Signals; DTE/DCE Switch; TD and RD Indicators; DC to 115.2 KBPS. The Model 63-2SA provides a hardware conversion for full duplex signals between RS-232 and RS-422 I/O ports. Since the RS-232 port may look like a computer or a modem, the converter is equipped with a DTE/DCE selector switch.
-
Product
Dual-Port Serial Interface Cards
PCI-COM2S And PCI-422/485-2
-
The PCI-COM2S and PCI-422/485-2 are dual-port, asynchronous serial communications cards designed for use in PCI-Bus computers. They are 6.5 inches (165 mm) long and may be installed in any 5V PCI slot in IBM and compatible computers. Each independent port supports RS-422 and RS-485 balanced-mode transmission/reception, and on the PCI-COM2S, RS-232 single-ended transmission/reception as well.
