-
Product
Low Profile PCI Express 2-Port
7202ec
-
The 7202ec low-profile PCI Express serial interface provides two RS-232 serial ports. All modem control signals are implemented for maximum compatibility with a wide range of serial peripherals. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7202ec ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
Product
PCI Direct Digital Synthesizers
SYNTH300-TRIG
-
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
Product
PCI Express Gen 1 Test Backplane
SKU-015-01
-
The PCI Express Test Backplane was designed to support production testing/debugging of PCIe-based peripheral boards. The backplane expands the x1 PCI Express interface of the host computer into one x4 and three x1 PCI Express slots via 7 ft CAT6 cable.
-
Product
Single Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-001
-
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
Product
cRIO-9058, 1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller
787044-01
-
1.33 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Artix-7 A100T FPGA, Extended Temperature, 8-Slot CompactRIO Controller - The cRIO-9058 is a rugged, deployable controller for data acquisition and control applications. It offers Intel Atom dual-core processing, an Artix-7 FPGA, and eight slots for C Series modules. It runs the NI Linux Real-Time operating system with access to the I/O through NI-DAQmx drivers or with LabVIEW. The controller provides precise, synchronized timing and deterministic communications over the network using TSN, ideal for distributed measurements and control. This controller offers two Gigabit Ethernet ports, one USB 3.1 host port, one USB 2.0 device port, a trigger line, and a μSD card slot for storing data locally. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
Product
PCI-5153, 500 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device
780318-01
-
500 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device - The PCI‑5153 high-speed oscilloscope device has two channels that sample up to 2 GS/s with flexible settings for coupling, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 500 MHz of analog bandwidth and flexible measurement configurations.
-
Product
PCI High Density Pecision Resistor Card, 18-Channel, 2Ω To 31.5Ω
50-298-010
-
The 50-298-010 is a high density programmable resistor card with 18 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Flexible x4 PCI Express to 4 MiniPCI Splitter
SKU-071-0X
-
Flexible x4 PCI Express to 4 MiniPCI Splitter was designed to expand your modern motherboard (ATX, mini ATX etc.) that doesn’t have a MiniPCI interface. It allows your to connect up to four 124-pin MiniPCI add-in boards to the motherboard ‘s standard PCI Express connector.Splitter includes 4 MiniPCI adapter boards, x4 PCI Express host board, and 4 flat PCI Express cables.
-
Product
Circuit Module, Riser for ISMB 2U PCIe X16 Riser Card to 2 PCIx8 Expansion Slots , and PCI card
AIMB-RP3P8-12A1E
-
Support ISG 2U chassis
-
Product
PCI Mezzanine Card
PNIC1G
-
Each Ethernet interface supports 10, 100 and 1000 Mbits transmission rates with auto-negotiation for full duplex operation; 10 and 100 Mbit/s transmissions for half duplex operation, and is equipped with a 32 Kbit Serial EEPROM.
-
Product
ATSC/DVB-T/QAM VHF/UHF Modulator For PCI
DTA-112
-
Cost-effective variant of DTA-115 with 75-Ω BNC main output and support for ATSC, QAM-A/B/C and DVB-T.
-
Product
PCI Digital I/O Cards
-
Sealevel PCI digital I/O cards are available with optically isolated inputs and Reed relay outputs. For high-voltage requirements, TTL versions provide convenient connections to industry-standard solid-state relay racks. Sealevel low profile PCI digital I/O boards meet the requirement for the MD1 low profile specification and feature Universal Bus (3.3V and 5V) for compatibility with both new and legacy computer systems.
-
Product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785961-01
-
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PCIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Squid PCI Express Carrier Boards for M.2 SSD Modules
SKU-064-2X
-
Flexible x1 PCI Express to 3 MiniPCI Express Splitter (Splitter) was designed to expand modern motherboard (ATX, mini ATX etc.) that have PCI Express interface. It allows you to connect up to three MiniPCI Express add-in boards to the standard motherboard PCI Express connector.Splitter includes 3 MiniPCI Express adapter boards, x1 PCI Express host board and 3 flat PCI Express Cables.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm
50-294-021
-
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
6-Port PCI Express
PEX 8724
-
The ExpressLane™ PEX 8724 is a 24-lane, 6-port, PCIe Gen 3 switch device developed on 40nm technology. PEX 8724 offers Multi-Host PCI Express switching capability that enables users to connect multiple hosts to their respective endpoints via scalable, high-bandwidth, non-blocking interconnection to a wide variety of applications including servers, storage, communications, and graphics platforms.
-
Product
PCI Very High Density Multiplexer, 49-Channel, 4-Pole
50-670C-022-49/4
-
The 50-670C-022-49/4 is a 49-channel, 4-pole MUX and is part of a series of very high density multiplexer cards feature a wide range of switching configurations. Typical applications include signal routing in ATE and data acquisition systems.The 50-670C shares exactly the same architecture as the established 40-670 range of PXI modules.
-
Product
Conduction Cooled XMC Interface Board with PCI Express Host Interface, Supporting up to 4 PX Modules, 2 RTx 5 Channel Modules, 1 Discrete & 1 Serial Module
EXC-8000ccXMC
-
The EXC-8000ccXMC is part of Excalibur’s 8000 family of multiprotocol boards. This conduction cooled XMC interface board has a PCI Express host interface and supports up to 4 Px modules, 2 RTx 5 channel modules, 1 Discrete and 1 Serial module. Due to the constraints of the XMC specification the modules are integrated onto the board itself rather than as physically separate modules.The EXC-8000ccXMC supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from modules that support DMA, with much less CPU overhead than when not using DMA.
-
Product
2-Axis Stepping And Servo Motor Control Universal PCI Card
PCI-1220U
-
Independent 2-axis motion controlHand wheel and jog function2-axis linear interpolation function2-axis circular interpolation functionContinuous interpolation functionProgrammable T/S-curve acceleration/deceleration rateUp to 4 Mpps output for each axisTwo pulse output types: CW/CCW or pulse/directionUp to 1 MHz encoder input for each axisTwo encoder pulse input types: A/B phase or up/downConstant speed controlPosition management and software limit switch functionBoardID™ switch
-
Product
PCI Express PLL Test Application
N1081PLCA
-
Keysight N1081PLCA PCI Express PLL Test Application designed to measure transmitter PLL bandwidth and peaking based on the PCI Express 5.0 TX PLL Specifications. Use N1081PLCA PCIe PLL test software to test, debug and characterize your PCIe designs.
-
Product
4-port/8-port USB 3.0 PCI Express Card With 4 Independent Host Controllers
AX92321
-
*Four or eight USB 3.0 ports*Four independent USB 3.0 host controllers*900 mA/1500 mA max. per port configurable via jumper settings*Compliant with USB 3.0 Rev.1.0 and Intel® xHCI Rev.1.0*PCI Express x4 interface*Operating temperature from 0˚C to 70°C*Supports Windows® 7/10*Supports each port’s power on/off via software settings
-
Product
PCI Express Graphic Card NVIDIA RTX 4000E Ada
NVIDIA RTX 4000E Ada
-
- NVIDIA Ada Lovelace Architecture- 5-year Longevity Support- Full height, full length design- PCIe Gen4x16 interface- 20GB GDDR6 Memory, 160-bit Bandwidth- 6144 CUDA Cores, 26.7 TFLOPS SP Peak
-
Product
DataBlaster PCI / PCIE JTAG Boundary-Scan Controller
JT 37x7/PCI
-
High speed and performance JTAG Boundary-scan PCI PC plug-in controller for PCI bus slot or PCIe PC plug-in controller for PCI Express bus slot.The controllers are targeted at demanding manufacturing test applications, fast in-system flash memory programming and programmable logic configuration. The JT 37×7 is available in different operating levels (memory options) to suit your specific environment and application. Each unit is supplied with a four TAP port signal conditioning module the JT 2147 ‘QuadPOD‘
-
Product
PCI Data Acquisition Boards
ADDA12-100DMA Series - Dual 12-bit A/D + Dual 14-bit D/A, 25 Ms/s
-
Model ADDA12-100DMA has two simultaneously sampling 12-bit A/D converters, two 14-bit D/A converters, five vectored TTL inputs and two vectored TTL outputs, and is able to transfer data directly into the computer system's memory at 100 MB/s in systems with 64-bit PCI slots or 80 MB/s in 32-bit slots.
-
Product
PCI-5152, 300 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device
779945-03
-
300 MHz Bandwidth, 2 GS/s, 8-Bit PCI Oscilloscope Device—The PCI‑5152 high-speed oscilloscope device has two channels that sample up to 2 GS/s with flexible settings for coupling, impedance, voltage range, and filtering. Oscilloscope devices also feature a number of triggering modes, deep onboard memory, and an instrument driver that includes data streaming and analysis functions. This device is ideal for applications with fast signals that require up to 300 MHz of analog bandwidth and flexible measurement configurations.
-
Product
PCI Express FMC Carriers
-
Sundance Multiprocessor Technology Ltd.
FMC carrier boards based on the PCI express format:
-
Product
PCI 32 Channel TTL Digital Interface
8010
-
The 8010 PCI digital I/O interface provides 32 channels of buffered drive digital I/O, which can be utilized for PC based control and automation of equipment including sensors, switches, security control systems, and other industrial automation systems. 10K pull-up resistors are included. Optional values are available.
-
Product
PCI To CardBus PCMCIA Type 1/2/3 Dual Slot Card, Ricoh R5C486 Controller
P222-Ricoh
-
The P222-Ricoh is perfect for use with Wireless LAN cards like WiFi / 802.11b or any of the newly emerging 802.11a or 802.11g standards and thanks to its second slot can simultaneously run a Bluetooth card or other type of PCMCIA or CardBus card.
-
Product
PCI 2 Amp Multiplexer, Dual 4-Channel, 4-Pole
50-635A-107
-
The 50-635A-107 is a dual 4-channel, 4-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
Product
PCI Express UltraScale+ FPGA Carrier Board With FMC+ Site, X16 PCIe Gen 4
PG4+
-
The PG4+ continues DEG’s commitment to delivering high performance processing solutions for mission critical applications requiring the latest in AMD UltraScale+ FPGA computing power. The PG4+ is a PCI Express, standard form factor, FPGA processor board designed to meet the needs of challenging, embedded high-performance digital signal processing applications. The AMD UltraScale+ VU37P or VU47P delivers superior processing capabilities and supports operations such as: FFTs, FIR filters, fixed-point and repetitive processing tasks. The PG4+ FPGA node processes input from the FMC HPC + (Vita 57.4) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules that operate up to 12 GSPS.
