Filter Results By:
Products
Applications
Manufacturers
Shock wave
short moment intense amplitude faster than sound wave
See Also: Wave, Long-Wave IR, Lightwave, Shear Wave, Sub-mm Wave, Microwave, Wavelet, Continuous Wave, Submillimeter Wave, Sine Wave, Millimeter Wave
-
product
Pneumatic Vertical Shock Test System
KRD11 series
KRD11 series pneumatic vertical shock test system is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and bump test, can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests.
-
product
The Nanomotor®
The patented Nanomotor® is a piezo driven linear motor. It is a multifunctional basic part for many positioning and manipulation devices. It has a positioning stroke of up to more than a centimeter while operating with atomic resolution. The Nanomotor thus bridges eight orders of magnitude. The Nanomotor consists of a cylindrical housing and a slider with a free axial hole inside. It combines high resolution in the sub-nanometer range with a large positioning stroke. The Nanomotor utilizes a piezo tube for fine positioning and a shock wave produced by the same piezo tube for coarse movements. The small Nanomotor is half the size of a match stick. It can lift six times its own mass. Every point of its stroke can be reached with a speed of up to 1 mm/s. The Nanomotor also works in ultrahigh vacuum or even under water. It is driven by a PC card at a supply voltage of only ±15 volts.
-
product
Pressure Sensors For Blast Testing
Pressure sensors with quartz, ceramic and tourmaline sensing elements are used for a wide variety of shock wave, blast and explosive testing. All of these applications require high frequency response and durability, ability to drive long cables and operate in adverse environments.
-
product
High-acceleration Shock Tester
DP-1200-18
King Design Industrial Co., Ltd.
The precise-type high-acceleration shock tester can provide all half-sine short wave specification specified in JESD22-B110. To meet them, merely change different shock rubber-pad on shock seat. The wave is complete with high repeatability, able to provide user accurate test result.Conform to different test specs such as JESD22-B110 and IEC spec.High repeatability on consecutive shock; acceleration +/- 10%; run time +/- 15%; speed deviation +/- 10%.Table’s four corner-points uniformity P160mm +/- 10%.Can add spring system to reach the requirement of extra high acceleration specification.Using high-efficiency vibration-absorbing seat pad can block out possible floor resonance and protect the factory structure.Easy in operation; no complicate training course required.Module shock rubber-pads are applied per different standards independently. And the rubber-pad lifetime can be prolonged.
-
product
Hydraulic Vertical Shock Test System
KRD10 series
KRD10 series full-automatic hydraulic shock test system is used to measure and determine the impact resistance of products or packaging, and to evaluate the reliability and structural integrity of products in a shock environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests to achieve the shock wave and impact energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
product
Environmental Testing
Environmental testing capabilities include: High and Low Temperature Testing including Thermal Shock. Humidity Testing to 100% Relative Humidity at High and Low Temperatures. Altitude Testing to 100,000 Feet. Combined Vibration, Temperature and Altitude Testing. Mass Spectrometer for Leak Testing. Vibration Testing to 50 G's and 3000 Hz including Resonance Scan, Cycling, and Endurance. Free Fall Half Sine Wave Mechanical Shock Testing to 100 G's
-
product
Shock Test Systems
Sanwood Environmental Chambers Co ., Ltd.
Is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and collision test, can perform conventional half-sine wave, post-peak sawtooth wave, square wave and other waveform shock tests.
-
product
Bump Tester
KD-163
King Design Industrial Co., Ltd.
*Comply with IEC-68-2-29 testing specification(10g/ 16ms、15g/6ms、 40g/6ms、100g/2ms).*Easy installation and simple operation; Low noise; no maintenance required; function holds long.*Well-designed and no resonant-structure, air anti- vibration pad can effectively isolate floor vibration.*Accelerometer adopts repeated measurement and adjustable half-sine wave generator; to control the data is precise.*Magnesium alloy platform is anodized, Servo motor cam to drive, and can adjust the frequency automatically.*The adjustable acceleration value and shock domain is patent design (1ms-13ms).
-
product
Gas Chromatograph
Weshine Electric Manufacturing Co., Ltd
The Oscillator shocks and heats up the oil sample to get the gas from the oil. And then inject the gas sample into the GasChromatograph. Before that,we should use the Air Generator and Hydrogen Generator to fire the FID1 and FID2.The Gas Chromatograph will analysis the gas sample automatically, and you will see the gases components waves on the software on PC.
-
product
Pneumatic Vertical Shock Response Spectrum Test System
KRD14 series
KRD14 series pneumatic shock response spectrum tester is used to measure and determine the shock resistance of electrical and electronic products or packaging, and to evaluate the reliability and structural integrity of the test product in a shock environment. The shock response spectrum is the total result of a series of single-degree-of-freedom linear systems with different natural frequencies subjected to the same shock excitation response. When a product is subjected to an impact, the maximum value of its impact response means that the product has a maximum stress. Therefore, the shock response spectrum tester can better simulate the shock wave and shock energy suffered in the real environment.
-
product
Acoustic Scoring System
AcoustiScore
Provide realistic weapons training. Consisting of a sensor and a data reception and display unit, the system senses the shock waves from passing projectiles and converts these waves into electronic signals for miss-distance measurement and display.
-
product
Ultrasonic Bolt Meter - Bolting System
Mini-MAX-Series
The MINI-MAX, Ultrasonic Bolt Tension Monitor, defines the state of the art in the measurement of the actual elongation produced by tightening a threaded fastener. The MINI-MAX can measure the elongation very accurately in fasteners of virtually any material from 1/2 inch to 4 feet in length. The measurement is achieved by determining the change in the transit time, of an ultrasonic shock wave along the length of the fastener as the fastener is tightened by any method. The on-board microcomputer automatically interprets this time measurement to display the time(nanoseconds), elongation, load, stress, or %strain from stretching a fastener. Through the use of high speed digital signal processing and automated diagnostics, the MINI-MAX minimizes the requirement for extensive operator training. With built in data recordation and reporting through an RS232 interface, the MNI-MAX offers an easy to use and reliable solution to the most difficult bolting problem.
-
product
Pneumatic Horizontal Shock Test System
KRD12 series
The KRD12 series shock test system is used to measure and determine the horizontal impact resistance of a product or package, and to evaluate the reliability and structural integrity of the test unit in a horizontal impact environment. The system can perform conventional half-sine wave, post-peak sawtooth wave, or trapezoid wave shock test to realize the shock energy that the product is subjected to in the actual environment, thereby improving the product or packaging structure.
-
product
Shock Reactance
ICR260 330
Lifasa - International Capacitors, SA
Shock reactors are necessary to limit the transient currents that occur in the connection of the capacitors.
-
product
Wave Quality Analyzer
APQM-711
The APQM-711 wave quality analyzer enables measurement, analysis and recording of 50/60 Hz network parameters and wave quality diagnostics according to EN 50160. The APQM-711 is an innovative and unique model, it has Wi-Fi communication with the included tablet. The tablet allows all operations to be carried out remotely and with its 10" touch screen it is very easy to operate. From the tablet you can operate the analyzer intuitively and quickly, we can also perform the preview of live data and reading and analyzing data stored in internal memory.
-
product
Wave Profiler
The Wave Profiler allows the user to measure non-directional wave parameters continuously for long periods of time with high temporal and spatial resolution in deeper water from the safety of an underwater mooring. The instrument is particularly useful for clients who need to measure long-period waves (such as rogue waves or infra-gravity waves), waves in wash and in wakes, and non-linear waves.
-
product
Shock And Vibration Testing
Alpes Lasers SA offers a service of shock and vibration testing. Originally designed for qualifying laser devices to the MIL-STD-810H defense standard, the same tests can be applied to a variety of different products.
-
product
Thermal Shock Chambers
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Thermal Shock Chambers are designed for the safe, efficient, and accurate environmental testing of electronics and consumer products, and aerospace, telecommunications, and military and defense components.
-
product
Thermal Shock Chamber
The Thermal Shock Chamber is specially designedwith independant temperature zones to facilitatethe automatic transfer of product under testthereby simulating a temperature shock to test the reliability of the product as per military and other international standards.
-
product
Millimeter Wave Converters
ZC-Series
*variable output power*wide dynamic range*wide frequency range*highly stable measurement*convenient handling
-
product
Shock Control
Shock testing simulates an extreme event that a unit under test is exposed to during handling, shipment, explosive event and/or daily use (e.g. dropping an object). The profile for this type of testing is defined by the shape of the time domain waveform together with its amplitude and duration. The m+p VibControl vibration control system offers full functionality for classical shock and shock response spectrum testing as well as for tests using external pulses or the capture of transient signals.
-
product
Shock Test Machine
Guangdong ALI Testing Equipment Co,. Ltd
Shock Test Machine Special in shock test is used to accurately measure the product fragility and evaluate the protective ability of product packaging.
-
product
Thermal Shock Chambers
Weiss Technik Thermal Shock chambers are designed to give quick transitions between a HOT and COLD temperature zones. Available in vertical, horizontal and liquid models. Thermal stock chambers are used in all industries including Automotive, Electronics, Aerospace, and others to help find product defects in electronic components and product assemblies. Thermal shock is important with MIL -STD 883 test standard.
-
product
Shock Test System
Labtone Test Equipment Co., LTD
Products are inevitably affected by impact, bump, free fall, tumbling etc. during production, transportation, loading and unloading as well as during the use of the products. All of these are transient excitation on the object, causing the object to produce mechanical characteristics of high speed, acceleration, strain rate instantly. These kind of characteristics are completely different from that in static load, and may cause problems to the object in terms of structural strength and stability and sometimes the object may fail. Therefore, it's necessary to study the effect of impact and reproduce the shock environment, to assess the structural strenghth and performance of the object under shock environment.
-
product
Directional Wave Recorder
MIDAS DWR
The most cost-effective solution to directional wave monitoring requirements in all shallow water coastal applications, The MIDAS DWR Directional Wave Recorder represents a significant advance in PUV wave recording technology.
-
product
Thermal Shock Testing
Thermal shock is a very important test for determining the reliability of a product when subjected to sudden changes in temperature and how this stress source can accumulate deterioration or physical damage in performance.
-
product
Sentinel V Waves Array
Teledyne Marine RD Instruments
Teledyne RD Instruments Sentinel V Waves Array combines our highly robust, field-proven WavesMon processing with our new 5-beam Sentinel V ADCP to provide the highest-quality waves and current profiles of any ADCP in use today.
-
product
Incline Shock Tester
HIACC Engineering & Services Pvt. Ltd.
Inline shock test system simulates a real shock environment to estimate the impact resistance or damage level of a product. The simulated environment replicates shocks produced during product handling, stacking shelves, loading/unloading and transportations. The incline shock test system is widely used in the packaging industry, scientific research institutions and transportation industry.
-
product
Millimeter Wave Products
Reliable Millimeter-Wave High-Power Products for Airborne, Maritime and Ground Mobile Deployment
-
product
Safety Shock Absorbers
As an alternative to the standard shock absorber, Safety shock absorbers are the tried and tested low cost method of preventing those occasional emergency stops. Designed for occasional use, they primarily serve as reliable, effective protection in emergency stop situations.
