Filter Results By:
Products
Applications
Manufacturers
- Frequency Devices Inc.
product
CompactPCI Instruments
Is a computer bus interconnect for industrial computers,combining a Eurocard-type connector and PCI signaling and protocols. Boards are standardized to 3U or 6U sizes, and are typically interconnected via a passive backplane. The connector pin assignments are standardized by the PICMG US and PICMG Europe organizations. The connectors and the electrical rules allow for eight boards in a PCI segment. Multiple bus segments are allowed with bridges.
-
product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB112
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x4 slot, one PCIe x16 slot, and ten 32bit/33MHz PCI slots
-
product
3U CompactPCI 32-Bit Backplanes with Optional Rear I/O
cBP-3208/3206/3204[R]
- PICMG 2.0 CompactPCI Specification Rev. 2.1 compliant- Numbers of slot: 8/6/4 slots (incl. system slot)- Width: cBP-3208R: 36HP (9-slot) cBP-3206R: 28HP (7-slot) cBP-3204R: 20HP (5-slot)- Right one slot is system slot and others are peripheral slots- 10-layer PCB for accurate impedance control and electr
-
product
PICMG® 2.11 47-Pin Hot-Swap Redundant 3U CompactPCI® 8HP 250 W Power Module
cPS-H325/48
- PICMG® 2.11 CompactPCI® Power Interface compliant- 3U CompactPCI® 8HP form factor- PICMG® 2.11 47-pin CompactPCI® in-rack power module interface- 250 W DC output- Active PFC (Power Factor Correction) meets IEC1000-
-
product
Dual 3U CompactPCI® Subsystem with Two 6-slot Backplanes and Two CompactPCI® Power Modules
cPCIS-2642 Series
- Dual 3U CompactPCI® Systems, each with five peripheral card slots and one system slot- 1/1 250 W CompactPCI® Power supplies- Temperature, voltage, and fan monitoring LEDs- Supports current sharing on +5 V, +3.3 V, and +12 V- PICMG® 2.11 47-pin power interface
-
product
1 PICMG® CPU, 1 PCI-E® x16,1 PCI-X™, 2 PCI™ Slots Backplane
EBP-5E1
- Segment: 1- Slots:1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-X™, 2 PCI™- Support ATX power supplies- Dimension: 153 mm x 330 mm
-
product
5-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB109
The FAB109 features a PICMG 1.3 CPU card slot, one PCIe x16 slot and three PCIe x1 slots, and built in a 24-pin ATX power connector and 8-pin connector for thermal detected board. Two high speed USB 2.0 ports are featured. The FAB109 is compatible with Axiomtek's AX60501 and AX6052 chassis.
-
product
10-CH General Purpose Timer/Counter & 8-CH DIO Module
cPCI-8554
- PICMG 2.0 Rev 3.0- Four 82C54 programmable timer/counter chips- Up to 12-CH 16-bit timer/counter- 1-CH 32-bit cascaded timer based on 8 MHz clock source- Four programmable clock sources for each timer/counter- Programmable de-bounce filters for external clock & external interrupt inputs- 8-CH TTL digital inputs & 8-CH TTL digital outputs- +12 V and +5 V power available on the connector
-
product
5-slot ATX-supported 2U Butterfly PICMG 1.3 Bus Passive Backplane
FAB105-V1
*Designed for PICMG 1.3 SBC*Compatible with the AX61222TP/AX61220TP chassis*Supports one PICMG 1.3 CPU card slot, one PCIe x16 slot, and three 32bit/33MHz PCI slots
-
product
3U CompactPCI 8HP 16.6-160VDC Input Railway Power Module
cPS-H325/WDC
- PICMG® 2.11 CompactPCI® Power Interface compliant- 16.6 to 160VDC wide input range, 310W- 3U, 8HP CompactPCI package- EN 50155 Class S2 and C2 compliant for power stability- 40°C to 85°C operating temperature with deratin*g
-
product
1 PICMG® CPU, 1 PCI-E® x16, 4 PCI-E® x1, 4 PCI® Slots Backplane
EBP-10E5
- Segment: 1- Slots:1 PICMG® CPU, 1 PCI-E® x16, 4 PCI-E® x1, 4 PCI®- Support ATX power supplies- Dimension: 330 mm x 318 mm
-
product
PICMG 1.3 Full-size SBC
Axiomtek's PICMG 1.3 full-size CPU cards (338 x 126 mm) offer high performance PCI Express slot as interface to the backplane, and improve I/O bandwidth and graphic performance from the original PICMG 1.0 specification.
-
product
14-Slot 32-Bit 6U CompactPCI H.110 Bus Backplane
cBP-6014R
- PICMG 2.0 CompactPCI Specification R3.0 Compliant- PICMG 2.1 CompactPCI Hot Swap Specification R2.0 Compliant- PICMG 2.5 H.110 Computer Telephony Specification R1.0 Compliant- PICMG 2.7 Dual system Bus specificationR1.0 compliant- One system slot with 13 expansion slots, system on the middle slot of the backplane
-
product
1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-E® x4, 6 PCI™ Slots Backplane
EBP-9E2
- Segment: 1- Slots: 1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-E® x4, 6 PCI™- Support ATX power supplies- Dimension: 328 mm x 206 mm
-
product
13-slot ATX-supported PICMG Bus Passive Backplane
ATX6022/13L
*1 PICMG, 4 PCI and 8 ISA*Compatible with AX61400, AX6145, and AX6156LE*Supports both AT and ATX power supply
-
product
Passive Backplanes
A wide range of ADLINK backplanes are available for PICMG CPU cards. They are the most flexible and expansible solutions for industrial slot-hungry applications.
-
product
PICMG 1.0 Full-Size Single Board Computers
PICMG 1.0 Single Board Computers (SBC) features comprehensive backplane support. The Slot SBC are the most flexible and expansible solutions for industrial applications.
-
product
13-slot ATX-supported PICMG 1.3 Bus Passive Backplane
FAB113
*Designed for PICMG 1.3 SBC*Compatible with the AX61400, AX6145, and AX6156LE chassis*Supports one PICMG 1.3 CPU card slot, seven PCIe x1 slot, one PCIe x16 slot, and four 32bit/33MHz PCI slots
-
product
1 PICMG® CPU, 1 PCI-E® x4 Slots Backplane
EBP-D3E1
- Segment: 1- Slots: 1 PICMG® CPU, 1 PCI-E® x4- Support ATX power supplies- Dimension: 331 mm x 39 mm
-
product
PXI/CPCI System Platform
PX44201
LinkedHope Intelligent Technologies Co.,Ltd.
PX44201 is a 3U PXI/CPCI system platform compliant with PXI Rev2.2, PICMG 2.0 specifications. With the air cooling design and PXI/CPCI modular design on the platform, PX44201 has excellent heat dissipation performance, and can save costs on maintenance in the long run.
-
product
COM Express® Type 6 R3.1 Reference Carrier Board In ATX Form Factor
Express-BASE6 R3.1
Express-BASE6 R3.1 is an ATX COM-Express Type 6 Basic / Compact size module reference carrier board based on PICMG COM-Express Revision 3.1. Together with the COM-Express Type 6 module of your choice and off the shelf add-on cards, you can quickly emulate the functionality of your desired end product for software development and hardware verification.
-
product
PICMG Single Board Computers
ADLINK's industrial Slot Single Board Computers (SBCs) and backplanes follow PCI Industrial Computer Manufacturers Group (PICMG) 1.0 and 1.3 standards, with card-on-backplane architecture delivering faster Mean Time to Repair (MTTR) over conventional motherboard designs, flexible backplane configurations, functional with a broad range of off-the-shelf peripheral cards. ADLINK’s wide range of PICMG 1.0/1.3 CPU board-compatible backplanes are fully co-functional with ADLINK systems, for flexible configuration and expandability in industrial applications.
-
product
4/8-port Asynchronous Serial Communications Modules
cPCI-3534/3538-S
- 32-bit CompactPCI, PICMG 2.0 Rev 2.1- Plug-and-play, IRQ & I/O address automatically assigned by PCI BIOS- 4/8 asynchronized communications ports with intelligent buffer- Three RS-232 ports and one isolated RS-422/RS-485 port with 2500 VRMS isolation voltage for cPCI-3534, and eight RS-232 ports for cPCI-3538- Surge protector in TXD/RXD signal line
-
product
6U Compact PCI® Single Board Computer
CP62001
LinkedHope Intelligent Technologies Co.,Ltd.
CP62001 is a 6U CompactPCI® single board computer designed based on Intel® GM45 chipset, compliant with PICMG®CompactPCI® specifications. There are SATAII, USB2.0, 10/100/1000Mb Ethernet, and Keyboard/Mouse interfaces on board. The display controller integrated in CP62001supports VGA and DVI dual output independently, with up to 2048×1536 resolution on CRT. Up to 4GB soldered memory on CP62001, leaves no worry about the board stability under harsh shock and vibration environment for end users. Besides, LinkedHope™ provides variant drivers BSP) support, such as VxWorks, Linux and Windows, as reduces the workload of system integration and the development of final solutions and shorten the Time-to-Market.The CP62001 with high performance/power ratio, works stably in extended temperature range, and is an ideal selection for high reliability and high availability required applications, like harsh environment communication, network security, video/image processing and can also be an ideal control unit in variant devices and equipment.CP62001 has a ruggedized version (called CP62002)with conduction cooling and wedge-lock technology. CP62002 is designed for extremely harsh environment.
-
product
COM-HPC Server Type 10G OCP Mezzanine Card
CEI-4x10GBASE-T
- Supports up to four 10GbE copper interface (10GBASE-T)- Compatible with PICMG COM-HPC Rev 1.0 Server Type compliant- For COM-HPC-sIDH module
-
product
5-Slot 32bit 6U CompactPCI H.110 Bus Backplanes
cBP-6105R
- PICMG:2.0 R3.0, 2.1 R2.0, 2.5 R1.0- Dimension (mm, WxH):120.9 x 262.05 (mm, WxH, vertical insertion view)- Segment:One- cPCI Bus:32-bit/33MHz- System Slot:Right-hand side (upper side for board's horizontal insertion)
-
product
1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-E®x 4, 2 PCI™ Slots Backplane
EBP-D5E2
- Segment: 1- Slots: 1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-E® x4, 2 PCI™- Support ATX power supplies- Dimension: 331 mm x 84 mm
-
product
3U CompactPCI® Subsystem with 8-slot Backplane and 1 + 1 CompactPCI® Redundant Power Modules
cPCIS-2632 Series
- 3U CompactPCI® backplane with seven peripheral slots and one system slot- Temperature, voltage, and fan monitoring LEDs- Supports current sharing on +5 V, +3.3 V, and +12 V- 1 + 1 hot swappable 250 W + 250 W CompactPCI® power supplies- PICMG® 2.11 47-pin power interface- Hot-swappable cooling fans & filter
-
product
PICMG 1.0 Half-Size SBC Backplane
PICMG 1.0 Half-size SBC Backplane designed with industry-standard ISA and PCI gold fingers for expansion. SBC Backplane equipped with fanless cooling and low-power configurations especially suitable for mid-range industrial applications.
-
product
3U Modular Processor Board
CP32105
LinkedHope Intelligent Technologies Co.,Ltd.
Based on Intel® Atom™ Processor, LinkedHope® designs CP32105 in a COMexpress® based modular 3U CompactPCI form factor. CP32105 is compliant with PICMG CompactPCI 2.0 specification, and it is low power, compact and fully integrated.CP32105 offers a variety of processor options from Intel Cedar View family, such as D2550, N2600 and N2800. CP32105 supports onboard SATA FLASH hard disk up to 64GB, which is designed mainly for installing operating system. With excellent anti-shock and anti-vibration performance, CP32105 can be operated stably on train, on ship, and in other special off road vehicles. CP32105 supports WLAN (Wireless Local Area Network) and 3G/4G wireless communication functions, which enable local and remote wireless data exchange easier than ever before.
