DC Current Clamps
-
Product
400/5A CHEAP SPLIT CORE CAST RESIN CURRENT TRANSFORMER
LZCK310-10
-
Beijing GFUVE Electronics Co.,Ltd.
LZCK series outdoor waterproof current transformers are applicable for AC power system 35kV and measurement of current of power supply equipment below 10KV also can be used for microcomputer protection. This type of current transformer employs imported silicon steel which with high permeability as magnetic material, has the characteristics of Small magnetic circuit loss and can be split, its semicircular core and secondary windings employ high quality epoxy resin vacuum, casting in plastic-case(ABS or PC) which is flame retardance anti-moisture, stable performance, no maintenance.
-
Product
Digital Arrester Clamp Tester (with Data output)
ALCL-40H
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*ALCL-40 is designed to test the diagnostic of OXIDE SURGE ARRESTER.*The least influence from the external magnetic field and noise by triple shielding of CT.*Compliant with IEC6099-5.*Enabled the measurements for 100nA resolution and harmonics current.
-
Product
Adapter, 1.0 mm (m) to 1.0 mm (m), DC to 110 GHz
11920A
-
The Keysight 11920A precision 1.0 millimeter waveguide-to-coax adapter offers a simple way of measuring coaxial devices at higher frequencies. It is designed for the measurement of components with 50 ohms impedance and frequency range from dc to 110 GHz.
-
Product
DC Blocking Power Splitter Combiner
PD7130
-
INSTOCK Wireless Components, Inc
True 3 Way Equal Split and BalanceWideband Frequency, 698-2700 MHzHigh Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portTri Alloy SMA Female (Jack) Low PIM
-
Product
Dual Surge Current Generator
MIG0612T-K12
-
Designed for testing telecom surge protection devices according to ITU-T K12. The generator has two indepedent impulse outputs which allow testing of two and three terminal protection devices such as gas discharge tubes (GDT). The generator can be configured for two terminal devices or with the outputs in parallel to increase the current impulse for two terminal devices.
-
Product
Clamp type DC/AC Current Sensor／with Voltage Output
LAD-250
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*With DC voltage output*AC/DC 1A～1000A
-
Product
DC Blocking L-Band Splitter Combiner
PD5920
-
INSTOCK Wireless Components, Inc
PD5920 is an IP67 outdoor, weather resistant, DC blocking, two way, RF broadband, 50 ohm, power divider, power combiner furnished with TNC coaxial connectors. The passive Wilkinson design passes RF, 10 MHz and DC current through one port, typically for powering an active antenna, with the other port blocking DC. Max voltage rating at the DC blocked port is 50 VDC. All wireless band applications in the frequency range from 698 to 2700 MHz are covered with best in class RF performance. The RoHS compliant PD5920 is a bidirectional device capable of 40 W max microwave input power level in both power splitter and combiner apps. See 2 way power divider input rating tables for additional power handling info.
-
Product
AC Clamp Power Meter
CM3286 Series
-
Measure power ranging from 5 W at a low current of 60 mA to 360 kW. In addition to current, voltage, and power, measure simple integral power consumption and phase sequence. Discover manipulation of electric meters by comparing meter and integral power consumption measurements. Discover theft by measuring leakage current.
-
Product
Clamp type AC Current Sensor／for Leakage Current Measurements(ZCT Series)
ZCT-140
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Leakage current measurements of feeder*Compact size*AC 1mA～300A
-
Product
DC Power Module, 35V, 3A, 105W
N6744B
Power Module
The Keysight N6744B is a 105 W basic DC power module that provides programmable voltage and current, measurement and protection features at a very economical price, making these modules suitable to power the DUT or to provide power for ATE system resources such as fixture control.
-
Product
Handheld Clamp Meter, 3 ½ Digit
U1212A
Digital Multimeter
Handle large currents up to 1000 A safely with 2-inch large jaw opening. Keysight Remote Link Solution allows datalogging wirelessly via Bluetooth.
-
Product
Adapter, 2.4 mm (f) to APC-7, DC to 18 GHz
11902B
-
The Keysight 11902B is a metrology grade, 2.4 mm female to APC-7 adapter with dc to 18 GHz operation.
-
Product
30 Amps, 50 MHz BW Current Probe - AC/DC , 50 Amp Peak Pulse
CP030
-
Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.
-
Product
T3CP Series AC/DC Current Probes
T3CP Series
-
Teledyne Test Tools AC/DC Current Probes are powered by an external universal power supply and work with any Oscilloscope with a high-impedance BNC input. The range of five current probes includes models with bandwidths up to 100 MHz, peak currents up to 500A and sensitivities to 1 mA/div.
-
Product
I/O Board With One GbE LAN, VGA And DC Jack For PICO841, PICO843
AX93267
-
*Specifications: 1 x DC jack, 1 x VGA, 1 x Gigabit LAN*Dimensions: 100 x 26 mm*Compliant products: PICO841, PICO843
-
Product
Precision Mechanical Calibration Kit, DC To 26.5 GHz, 3.5 Mm
85052C
Mechanical Calibration Kit
The Keysight 85052C precision mechanical calibration kit contains precision standard devices to characterize the systematic errors of Keysight network analyzers in the 3.5 mm interface. This kit also contains adapters to change the gender of the test port and a torque wrench for proper connection.
-
Product
AC/DC Split Core Current Sensor CT1000S
-
This AC/DC split core current sensor is designed for measuring large DC and AC currents in applications such as electric vehicles, renewable energy systems, inverters, and motors. It facilitates high-current measurements by clamping around existing current connections. With its voltage output, this sensor is compatible with power analyzers (WT series and PX8000) and waveform measurement instruments (ScopeCorders and DLM series), making it a versatile tool for various high-current measurements.
-
Product
High Current Calibrator
MC151
-
MC151 Current calibrator is an accurate current source capable of 120 A. Typical uses include calibration of current sensors, current probes, current transformers, shunts, ammeters, DMMs or as stable current source for test and development applications. The calibrator is equipped with a built-in multimeter that can be used for simulation of programmable transconductance or current amplifier.
-
Product
Low PIM Coaxial Switch, DC to 20 GHz, SP4T
87104Q
-
Low passive intermodulation (PIM) is crucial for applications where two or more transmitted signals share a common antenna or whenever the transmitter signal is too high or the receiver is sensitive to high intermodulation. The Keysight 87104Q is a low PIM SP4T coaxial switch, operating from DC to 20 GHz, which can help to keep the system PIM level low. A guaranteed 0.03 dB insertion loss repeatability and 3 million cycles of operating life ensures signal integrity, improves testing efficiency and ultimately maximizes test throughput.
-
Product
Enclosure, S6, 1U Height, 4 Cable Clamps, 8" Depth
410112702
Enclosure
Enclosure, S6, 1U Height, 4 Cable Clamps, 8" DepthIncludes hinged cover and 4 cable clamps for discrete wiring that provide secure strain relief. With cable clamps in open position- stiffener bar may be removed to allow installation or removal of cables without requiring wiring to be disconnected from the assembly.Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Series Precision Fixed-Ratio Current Transformers
PMT25100
-
Power Measurement Technologies Inc.
Precision two-stage toroidal current transformers find application as the reference in determining the accuracy of instrumentation current transformers.
-
Product
4-in-1 OSLT Mechanical Calibration Kit, DC To 40 GHz, 2.92 Mm (f)
85561A
Mechanical Calibration Kit
Combines an open, short, load, and through standard in a compact unit that is easy to handle and lightweight.
-
Product
4-in-1 OSLT Calibration Kit, DC to 70 GHz, Type-1.85 mm (m)
CK058M
-
The Network Analyzer Calibration Kits with open, short, load, and thru (OSLT) provide the RF components needed to enable stable and accurate error correct measurements. Calibration of a network analyzer using Spanawave's Network Analyzer Calibration Kits allow for precise measurements. The Calibration Kits offer broad test equipment coverage for use with the 8003 Scalar Network Analyzer as well as being compatible with most network analyzers produced by other manufacturers. Spanawave calibration kits yield complete calibrations, as it takes into consideration the three major sources of systematic error correction by one port calibration at both ports.
-
Product
DC Power Supplies
HPX Series
-
AMETEK Programmable Power, Inc.
The Sorensen HPX series serves every major market and application that requires demanding test specifications, from industrial automation to material research to aerospace and satellite testing – providing engineers the flexibility they want with the capability they need all in one convenient and affordable system. The Sorensen HPX High Power Extensible, Programmable DC Series delivers unsurpassed quality and reliable low-noise performance, fast and precise programmability with premium features, all in a convenient rack-mount cabinet with casters.
-
Product
DC Power Supply
PW-3032
-
*Low Ripple & Noise*30V/3A+5V/3A Dual output.*<0.4m Vrms Ripple & Noise(C.V.)*<2.5m Arms Ripple & Noise(C.C.)*Dual Display.
-
Product
Low Input Bias Current Amplifiers (<100 pA)
-
Low input bias current op amps are required whenever the difference of currents or voltage is small and needs to be measured accurately. These op amps are used so that the signal is not loaded down by the input of the op amps. Low input bias current op amps are critical for interfacing sensors in applications from photodiodes, pH meters, or other electrometer related functions to downstream electronics. Analog Devices has many precision op amps that fit the definition and range of these applications.
-
Product
Leakage Current Tester
TOS3200
-
The Leakage Current Tester TOS3200 is designed to perform leakage current (touch current and protective conductor current) tests on general electrical equipment but not medical electrical equipment.It enables you to conduct tests that conform to the requirements of the applicable IEC, UL, JIS, and other standards, as well as the Electrical Appliance and Material Safety Law. The memory in the main unit stores the 51 types of test conditions laid down in the IEC/JIS standards for information technology equipment, household electrical appliances, audio, video electronic apparatus, luminaires, motor-operated electric tools, and electrical equipment for measurement and control and in the Electrical Appliance and Material Safety Law, thereby enabling you to conduct standard tests with simple panel operation.
-
Product
PXI/PXIe Battery Simulator Module, 2-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-913
Battery Simulator
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 2-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
sbRIO-9208, Non-Enclosed, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module
780979-01
Current Input Module
Non-Enclosed, 500 S/s, ±20 mA, 16-Channel C Series Current Input Module - The sbRIO‑9208 is designed with industrial systems in mind. It includes a high-resolution mode with 50/60 Hz rejection to remove low frequency noise. It has high-channel density to reduce the number of modules needed, which leaves slots open for other measurement types or for reducing the overall per channel cost of the system. The sbRIO‑9208 uses a standard D‑SUB connection for use with cables and connector blocks. Non-enclosed modules are designed for OEM applications.
-
Product
High Power LED DC Electronic Load
33430G Series（1800W / 3600W）
-
Each 33430G Series has its own control and display panel, LED/CC/CR/CV/CP/ Dynamic modes, panel with 150 sets Store/Recall memory which provides load set-up more efficiently，also can be controlled intranet via RS232、Ethernet、USB and GPIB interface.
