IV
measure of current flow as a function of voltage.
-
Product
I-V Measurement Systems
-
The I-V Curve Data Acquisition includes a fixture for holding cells for testing (see Figure 1 below). This fixture can accommodate cells from small to up to 100 mm x 100 mm. Adjustable cell stops, in the X & Y-axis, are provided to consistently locate the cells for testing. Two micro-manipulators are provided as shown in Figure 1. Each micro-manipulator has two spring loaded contacts to allow 4-wire measurement even for cells that have top contacts only. Two back-side voltage contacts are embedded in the Plate (galvanically isolated from the Plate) and make good electrical contact when the cell is held down by vacuum to the plate. All voltage and current probes are gold-plated. The cell is held down with vacuum during testing (built-in vacuum pump).
-
Product
Semiconductor Switching Systems
Keithley 700 Series
-
The high speeds and low currents of semiconductor devices demand high quality, high performance switching of I-V and C-V signals. We offer switching solutions for both semiconductor R&D and production test applications with mainframes that can support up to 2,880 channels and a family of matrix cards designed specifically for semiconductor applications.
-
Product
Solar Cell Testers
-
Solar Cell Testers are integrated systems incorporating Solar Simulator and I-V Measurement systems. PET offers Standard and Advance IV Measurement software. PET Cell Testers are capable of measuring a diverse range of solar cell parameters such as Isc,Voc, Imax,Vmax, Pmax, FF, Rsh, Rs and η cell conversion efficiency, complete light and dark I-V curves. All that needs to be done to test a cell is to load the cell, make electrical probes contact and press “Measure” icon on the I-V Measurement System software. The software will automatically open the Solar Simulator shutter, perform the test and close the shutter after the test is complete. The design is modular in nature and can be easily upgraded. Some options can added at a later time.
-
Product
Reference Cells
-
Reference cell is used for measuring and setting the intensity of solar simulators for one sun (or other user desired) intensity condition. They are also used to calibrate the IV Measurement system photo-detector intensity to match the measured ISC to calibrated ISC.
-
Product
Digital LCR Multimeter
MT-5211
-
MT-5211 is a Fully featured multimeter with LCR meter. Ideal for a wide variety of electrical and electronic testing applications. Comply with CAT IV 600V.
-
Product
Ferroelectric Tester
Premier II
-
The Precision Premier II, is one of Radiant's most advanced test systems. The Premier II has the large envelope in terms of frequency response, voltage range, and accuracy of any ferroelectric tester in the world. Vision Software is provided with the Premier II Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choice from.
-
Product
Multimeters
-
Bluetooth interface for downloading, viewing, and sharing on Southwire’s MApp™ mobile appOnboard memory allows datalogging even when Bluetooth wireless is not connectedHi-Res color display with graphing featureOn board memory for saving and viewing measurements and recordingsIntuitive menuRugged meter with CAT IV 600V / CAT III 1000V
-
Product
Tester For PV Modules And Small PV Installations Up To 1000V, 40A
PVPM1040X
-
The PVPM1540X I-V curve tracer from PV-Engineering is a portable peak power measuring device for photovoltaic strings and arrays up to 1500 V / 40 A.
-
Product
Photovoltaic Array Simulation Solution
-
The Keysight N8937APV and N8957APV photovoltaic array simulators are capable of testing PV inverters up to 1,500 V, enabling designers to participate in the recent industry shift to the higher voltage. They can quickly simulate I-V curve characteristics under different environmental conditions (temperature, irradiance, age, cell technology and more), enabling the user to quickly and comprehensively test their solar inverters.
-
Product
Time Domain Reflectometer
BAUR TDR 510
-
Handheld Time Domain Reflectometer TDR 510. The BAUR handheld time domain reflectometer TDR 510 is used for fault location in all metal cables such as power cables, coaxial cables, data cables and communication cables. The BAUR TDR 510 comes with a device storage for 50 measurements and the option to compare the trace of an active TDR measurement with a stored trace.* Configurable for various measurement ranges and cable types* Standard-compliant, safe measurements on live cables through the measurement category CAT IV / 600 V* Ideal for fault location in the area of telecommunication, video technology, data and security technology
-
Product
SolarIV Series Solar Cell Current Voltage Measurement System
SlarIV
-
SolarIV IntroductionOne of the key measurements needed for photovoltaic devices in the measurement of their I-V characteristics. Through measuring the I-V curves the user can determine physical performances of devices such as photo-electric conversion efficiency, fill factors and so on. Such data is important for reliable work in research and quality inspection. ZOLIX supply the SolarIV system and the most perfect, professional technical support.
-
Product
Multimeters
-
Whether you work in industrial, HVAC, commercial or residential electrical environments, there’s an Amprobe digital multimeter with features to match your requirements. From heavy-duty industrial Amprobe DMMs with CAT IV safety ratings, to pocket size meters that handle all the basics, Amprobe makes some of the best digital multimeters around. Whatever your application, there’s an Amprobe multimeter ready to get the job done.
-
Product
Triple Alarm CAT IV Non-Contact Voltage Detector with Flashlight
FLIR VP50-2
-
The FLIR VP50-2 is a durable, CAT IV-rated non-contact voltage detector featuring light, vibration, and beeper feedback alarms and a powerful LED flashlight. Use the VP50-2 to reliably check if an AC circuit is live before beginning work; detect voltage on exposed conducting parts or through insulation; identify live wires within electrical panels, switches, and outlets; or trace live wires and map circuits. With an ergonomic and drop-tested design, the FLIR VP50-2 is the right choice for professionals performing field troubleshooting and verification of electrical installations within residential, commercial, and industrial buildings.
-
Product
3 Phase Meter - Anti-Clockwise
135012
-
IEC 1010 Rating: 1000V Cat III/600V Cat IV Double/Reinforced InsulationFeatures: For Use In The Installation and Operation Of 3 Phase Equipment.
-
Product
RX-IV Rangefinders
-
The ultimate smart rangefinder, the RX-IV offers precision ranging out to 1,500 yards, an inclinometer for the true Ballistic Range to your target, an 8x28mm multi-coated optical system for clarity, and much more.
-
Product
PXI-4132, 100 V, 2 W Precision PXI Source Measure Unit
780558-01
-
±100 V, 10 pA Precision PXI Source Measure Unit—The PXI-4132 is a programmable, high-precision source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4-wire) sense as well as external guarding. With its high measurement resolution integrated guarding, the PXI-4132 is ideal for high-accuracy leakage measurements on integrated circuits, discrete components, PCBs, and cables. You can also perform high-speed I-V measurements on a variety of components including diodes and organic LEDs using the onboard hardware sequencing engine. In addition, you can synchronize multiple PXI-4132 modules using the PXI backplane to provide high-speed I-V measurements on transistors and more complex devices.
-
Product
Cryogenic Probe Station
EMPX-HF
-
The Lake Shore EMPX-H2 probe station enhances standard probe station capabilities with the addition of a ±0.6 T horizontal field electromagnet. All standard C-V, I-V, microwave, and electro-optical probing, plus in-plane horizontal field electromagnetic measurements can be performed on this versatile station. Researchers can use it for testing magneto-transport parameters. The EMPX‑H2 is Lake Shore’s premier probe station for vector-dependent magneto-transport measurements.
-
Product
VFTLP+ Test System
4012
-
The Model 4012 VFTLP+™ test system was developed in early 2000 to add high speed measurements to the usual I-V plot, to measure and record the real TDDB waveform which causes oxide failure.*Accurate measurements of this waveform have finally been identified by Barth Electronics Inc. and CDM protection can now be based on known dimensional design parameters. We identify the response of your CDM protection circuits with 100ps risetime pulses which simulate the real CDM test. This is the only way with which to provide the total gate oxide threat voltage data.*Convenient, precise, repeatable operation*Computer controlled for automated testing
-
Product
Oscilloscope: 200 MHz, 4 Analog Channels
DSOX4024G
-
The 4000 X-Series boasts 12.1-inch display, capacitive touch screen technology, InfiniiScan Zone touch triggering, 1-million-waveforms/sec update rate, MegaZoom IV smart memory technology and standard segmented memory.
-
Product
Precision Source / Measure Unit (2 Ch, 10 FA)
B2912B
-
The Keysight B2912B precision source / measure unit (SMU) is a 2-channel, compact, and cost-effective benchtop SMU with the capability to source and measure both voltage and current. It easily measures current versus voltage (I/V) with high accuracy. The 4-quadrant source and measurement capabilities enable taking I/V measurements without configuring multiple instruments.
-
Product
Tube-Above Wavelength Dispersive X-ray Fluorescence Spectrometer
ZSX Primus IV
-
As a tube-above sequential wavelength dispersive X-ray fluorescence spectrometer, the new Rigaku ZSX Primus IV delivers rapid quantitative determination of major and minor atomic elements, from beryllium (Be) through uranium (U), in a wide variety of sample types — with minimal standards. ZSX Guidance supports you in all aspects of measurement and data analysis. Can accurate analysis only be performed by experts ? No — that is in the past. ZSX Guidance software, with the built-in XRF expertise and know-how of skilled experts, takes care of sophisticated settings. Operators simply input basic information about samples, analysis components and standard composition. Measured lines with the least overlap, optimum backgrounds and correction parameters (including line overlaps) are automatically set with aid of qualitative spectra.
-
Product
True-RMS Auto Range Multimeter
MT-1710
-
3 3/4 digits 3999 counts. 0.5% best accuracy.Both Auto and Manual range.CAT IV 600V safety rated.AC True-RMS for accurate measurements.Large backlight LCD display for easy reading.Extra functionsContinuity with beeperDiode testTransistor testDuty cycleRelativereferenceData holdAuto power offLowbattery indicationInput alert. Ideal for a wide variety of electrical and electronic testing applications.
-
Product
Parameter & Device Analyzers, Curve Tracer
-
Precision Current-Voltage Analyzer Series ensures accurate and efficient current-voltage measurements that give a clear insight into IV characteristics across a wide range of applications. The powerful characterization software and integrated source and measurements units (SMUs) make it much quicker and simpler to obtain accurate IV characterization. The EasyEXPERT group+ software supports all the characterization tasks such as measurement setup and execution, data analysis, data management and protection and so on, using the graphical intuitive user interface and mouse/keyboard operation. The Series provides a wide selection of IV analyzers suitable to your specific measurement needs in the range from an economic model to the most advanced analyzer capable of supporting cutting-edge applications.
-
Product
Open Circuit Locator
A994
-
The A994 is an open circuit locator for electric and telephone cables wind on the reel; it gives the position of the fault from the inside or outside end of the cable, in percentage to the total cable length. The instrument measures the ratio of the capacitances of the two sections of failed conductor using two high precision i/v converters. The advantage of this method is due to the fact that the measurement error depends almost exclusively on the dimensional inhomogeneity of the cable. The A994 has the unique feature to permit the location of fault in cables with all broken wires. This instrument locates breaks in cables with a total capacity between 2 nF and 5 uF. The distance to fault is displayed on a large LCD display.
-
Product
Infusion Pump Analyzer
FT-2 FlowTrax®
-
The STANDARD FT-2 FlowTrax® IV Pump Analyzer provides the fastest, most accurate test results – within a remarkable 3 minutes. Integrated full-featured pressure & temperature meters plus digital timer saves the time and cost of buying/calibrating four devices!
-
Product
Ferroelectric Test System
LCII
-
Precision LC II is an affordable Ferroelectric Tester for research labs. This system offers 5Khz at 9.9V and also comes in a built in 10V, 30V, 100V, and 200V option. This unit can also be expanded to 10kV for bulk ceramic testing. Vision Software is provided with the LCII Test System. Vision uniquely allows the user to construct complex or simple programs with any number of tests to characterize all aspects of the sample in one execution while keeping track of the measurement results and the history of the sample being tested. Tasks such as Hysteresis, I/V, C/V, PUND, Waveform, Magnetoelectrics, Piezoelectrics are just a few features to choose from.
-
Product
Monochromator Gratings - Type IV
-
HORIBA Scientific produces a wide range of holographic master gratings from which high precision replicas are manufactured.Using Type IV aberration-corrected monochromator gratings, a single concave grating disperses, collimates, and refocuses the light from the entrance slit onto the exit slit. Wavelength scanning is obtained through a simple rotation of the grating.The groove spacing of these gratings is computer-optimized to produce high quality images with a minimum of astigmatism and coma, even at large numerical apertures. Compared with Czerny-Turner monochromators (equipped with one plane grating, one collimating mirror and one focusing mirror), Type IV aberration-corrected monochromator gratings provide much better light collection efficiency and signal-to-noise ratio.
-
Product
NEXYGENPlus PET Testing Software
-
AMETEK Sensors, Test & Calibration
The NEXYGENPlus PET testing software can control the barrel temperature, display test graphs and automatically calculate the required test results, e.g. IV, degradation factor and MV. User specified pass/fail limits can be set for the IV, degradation factor and/or MV and the software will indicate which samples have passed or failed. When several tests have been performed, the batch statistics can be viewed either as a data table, an X-bar range chart or a histogram.
-
Product
Handheld Instruments
-
Measuring DC and AC voltages up to 1000 V.Alternating current and direct current with resolution up to 0.01 mA.Measuring continuity, resistance, diodestest, capacity, frequency.MIN / MAX recording.CAT III 1,000 V, Cat IV 600 V; IP54.Wireless remote display. Smartphone connection.Fluke Connect Mobile App for Android and iOS, compatible with over 20 different Fluke products.
-
Product
Solar Cell I-V Characterization System
VS6825
-
Industrial Vision Technology Pte Ltd.
The VS-6825A I-V test system is tailored for high-efficiency Solar cell production lines. It is able to eliminate the impact of HJT/IBC/TOPCON’s high capacitance characteristics on measurement results.
