Analog I/O
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
-
product
Digital And Analog Call Simulation
GL’s T1 E1/Analog Test Suite supports analysis and emulation of legacy protocols (MFCR2, E&M, SS1/SS4, SS5, Voice Call Signaling, 2-wire Call, SF Signaling (DTMF)) applicable to Federal Aviation Administration "FAA" within their National Airspace System "NAS" Ground-to-Ground Air Traffic Control Network and Voice System (NVS) to Analog Interphone.
-
product
Analog Power Modules
Renesas' family of analog power modules offers users a fully integrated DC/DC switching buck converter in one package. These modules combine the controller, power FETs, output inductor, and compensation circuitry in a single package minimizing both the external component count and complexity of converter design.
-
product
Analog Signal Generator
ASG
The pocket size model ASG Analog Signal Generator is an ideal tool for troubleshooting transmitters, transducers, motors and actuators. The unit generates a 0 to 10 VDC signal in increments of 1 volt or a 4 to 20 mA signal in increments of 2 mA. An LED bar graph visually indicates analog signal level. The model ASG will also continuously ramp to user defined maximum and minimum values with user defined ramp interval timing. Units are furnished with 6 ft (1.8 m) leads with alligator clips, 120 VAC plug-in adapter, protective carrying case and instruction manual.
-
product
Analog Power Supply
Type NPS-2412
National RF's Type NPS-2412 analog power supply was designed to be used in communication equipment where radiated switching inverter noise from conventional “switching type” supplies is not acceptable. The power supply consists of a standard rectified transformer output driving a pair of voltage regulators and filtering networks. The 2412 offers an adjustable voltage output between 2 and 24 volts as well as a fixed voltage output of 12 volts. A maximum of 20 Watts of DC power can be supplied from the unit. As the voltage regulators dissipate power in the regulation process, the power to the load is derated accordingly, dependent on the set voltage to the load. The adjustable regulator is a standard LM-317T integrated circuit device. The fixed regulator is a standard LM 7812 device. Upon customer request, the LM 7812 device may be changed to any voltage rating within the the LM-78xx series of regulators. Contact National RF for this modification if desired.
-
product
True Dual-Channel Analysis on iOS
IOScope
With IOScope, measure loudspeaker impedance, frequency response, and sensitivity. Measure a room impulse response. Tune a large sound reinforcement system, time-align a set of surround sound speakers, or optimize your home stereo. Determine the actual cutoff frequencies of your latest speaker crossover circuit, or teach your students the fundamentals of Fourier analysis of dynamic systems.
-
product
AcroPack® I/O Modules
Acromag provides software support packages for embedded applications running on Linux®, Windows®, or VxWorks® operating systems. The libraries provide generic routines to handle reads, writes, interrupts, and other functions. Demonstration programs enable the developer to quickly exercise the I/O modules before attaching the routines to the application program. This diagnostic tool can save hours of troubleshooting and debugging.
-
product
Analog Input Module
IP340
These modules have sixteen analog inputs which are sampled as two eight-channel banks. Eight A/D converters (ADCs) permit simultaneous conversion of all eight channels in a bank. A FIFO buffer holds the first bank’s data while the second bank is converted. Conversion of each bank requires only 8µS, and all 16 channels can be sampled in just 16µs.
-
product
PXI 32 Channel I/O, High and Low Side Driver
40-413-003
The 40-413 range is available in three configurations, a high side only, a low side only and a combined high and low side (shown here) –each capable of driving 2A loads. Each output is fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments.
-
product
Analog Force Gauges
Phase II force gauges are designed and engineered to achieve WORLD-CLASS tension/compression measurements. Heavy duty construction allows the force gauges to undergo rough handling in any environment, while providing for extremely sensitive and highly accurate readings. The Phase II force gauges include a direct dual scale reading in both lbf and kgf, eliminating the need for two separate gauges in the shop.
-
product
Analog Panel Meters
Jewell Instruments offers a wide range of moving iron, moving coil, and stepper motor analog panel meters in A&M, Emico, Jewell, and Modutec Series.
-
product
Protective Function Analog Multimeter
MT-2018
Complied with 2008 CE safety standardMirrored Aluminum dial plate20k/V DC & 9,k/V AC input sensitivityOverload and mis-used protectionAdjustable back tilt device with hook-up designRobust protective holster alongsideResistance, Current & Voltage measurementsTransistor hFE TestBattery TestTest leads, batteries, fuse and user's manual includedIdeal for using in the fields of lab, school, home applications and more
-
product
Analog Products
Our broad analog component portfolio provides for a wide range of next-gen precision instrumentation, medical, communication, and industrial process control applications where high performance and high precision sit alongside innovation, reliability and dependability as central to the analog design.
-
-
product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 5V
APCIE-1564-5V
32 digital inputs, 5 V, isolated16 interruptible inputs32 digital outputs, 5 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
-
-
product
Analog Pressure Gauges
Analog pressure gages use a needle to indicate the pressure sensed on a dial scale. Analog pressure gauges are inexpensive, easy to use, and don’t require a power source.
-
product
PC/104 OneBank I/O Board
EMC²-KU35
Sundance Multiprocessor Technology Ltd.
The PCIe/104 OneBank™ design enables the EMC²-KU35 to be added to robust and rugged installations for various commercial, medial, industrial and military uses and to enable more versatility the EMC²-KU35 also incorporates a VITA57.1 FMC™ LPC connector opening up an range of extra possibilities and expansion options.
-
product
Digital and Analog Test Sets
Our analog and digital automated test system experience covers a wide variety of applicationsfrom multiple path resistance, capacitance, and inductance testing using various Interface Test Adapters (ITA)to inter-connect multiple customer units under test (UUT). Other systems have included: equipment to monitor and record telemetry, digital data streams, and systems that evaluate packet data using a variety of VME, VXI, PXI, and LXI equipment.
-
product
High Speed Digital I/O
ADLINK's high-speed digital I/O cards features 32 or 64 high-speed single-ended I/O channels and up to 50 MHz data transfer rate with 200 MB/s data throughput—ideal for large-scale digital data exchange.
-
product
Analog Transducers
CR Magnetics Analog Transducers provide the easy to use tools to monitor any electrical power system, power supply, or electrical load. From simple DC to DC voltage transducers, to complex real and imaginary power transducers, CR Magnetics has the exact input, output, and sensing technology to meet the needs of any electrical power sensing application.
-
product
Digital I/O via Ethernet
2610
Connects to Ethernet via 2601 communication moduleAll channels may be independently programmed as input or outputEight channels have pulse width modulation outputsRJ-11 I/O connectors eliminate need for external terminal blocksSupport for interlocks and multiple power supplies per channelInput channels are debouncedWatchdog Timer
-
product
I/O Module
VPX3-611
Curtiss-Wright Defense Solutions
The VPX3-611 I/O module allows customers to readily incorporate a wide variety of I/O into military and aerospace embedded computing systems. Using a simple and reliable Flash-based FPGA hardware architecture with flexible I/O signal routing, the VPX3-611 provides high data throughput performance and can be easily adapted to meet a wide range of application needs.
-
product
FMC-LPC I/O Module
FM191
Sundance Multiprocessor Technology Ltd.
The FM191-RUA1 has a VITA57.1 FMC-LPC connector and follows the electronics specification and recommendations of the standard but is NOT form-factor compatible and will NOT fit all FMC carriers. Two versions are available. The FM191-R main features are a daughter card which provides 5V-TTL-compatible Analogue and Digital GPIOs that are suitable for robotics, motors and sensor application.
-
product
Modbus Analog Output Modules
DAT3020 Series
The DAT3020 series from Datexel is a range of Modbus analog output cards. These cards or modules have both voltage and current outputs either 0-10V or 4-20mA and are isolated from the input, output and power supply. They are available with either 2, 4 or 8 channels. The DAT3011 is a Modbus slave with 2 analog inputs (Thermocouple, RTD's mA, Resistance, Potentiometers, mV and voltage) and 2 analog outputs(4-20mA). It also has 3 digital inputs and outputs. Combining these analog output cards with the analog input cards, and the digital IO cards with the DAT9000 controllers make Datexel the smart choice where Data Acquisition is needed.
-
product
Analog and Digital Interface
425
Three quadrature encoder channels with 16-bit countersFour 12-bit D/A outputsEight 12-bit differential A/D inputs, 50 kHz rateWatchdog timerForty-eight bi-directional digital signals for solid state relay boardsPC/ISA compatible
-
product
Digital-To-Analog Converters
Teledyne e2v has been innovating data converter technologies for over 20 years and offers some of the most powerful digital to analog converters on the market that feature:Signal generation of up to 7 GHzLatency as low as 1 nsFull scale step response times as low as 40 psLowest noise vs. performance on the market at microwave frequenciesThe cutting-edge technology packed into Teledyne e2v's data converters allow our customers to significantly simplify designs with licence free, standard and customized solutions.
-
product
Digital Reconfigurable I/O Device
The Digital Reconfigurable I/O (RIO) Device features user-programmable FPGA for onboard processing and flexible I/O operation. You have complete control over the synchronization and timing of all signals and operations along with custom onboard decision-making that executes with hardware-timed speed and reliability. You can configure user-defined hardware for a wide variety of applications, such as custom digital DAQ, high-speed waveform generation, sensor simulation, hardware-in-the-loop (HIL) test, custom digital communications protocols, bit error rate testing, and other applications that require precise timing and control.
-
