Analog I/O
Analog I/O are Devices that have the capability of sending and receiving analog signals.
-
product
PXI-6733, 16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module
778512-01
16-Bit, 8-Channel, 1 MS/s PXI Analog Output Module—The PXI‑6733 is a high-speed analog output device designed to deliver simultaneous, multichannel updates for control and waveform output applications, such as stimulus-response tests (including acoustic distortion testing) and simulation (such as three-phase power simulation). In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6733 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
Analog Platforms
(T1/E1/T3/E3/OC-3/OC-12/STM-1/STM-4)
Almost all T1 E1 T3 E3 Testers can be accommodated into rack-based units. Multiple rack units can be stacked together for greater scalability. Shown below is a rack based tProbe™ T1 E1 / T3 E3 Analyzer unit, and a Channelized T3 E3 Analyzer unit supporting 6 T3s (6 * 672 DS0s). Such customized rack serves the purpose of handling multiple communications lines and test complex functionalities.
-
product
Digital and Analog Communications
1. Design and implementation of RF oscillators and filters. 2. Design and implementation of analog AM and FM modulation and demodulation. 3. Design and implementation of digital and analog converter. 4. Design and implementation of ASK and FSK modulation and demodulation. 5. Design and implementation of PSK and QPSK modulation and demodulation.
-
product
PCI Digital I/O
APC464
Four 16-bit multifunction counters/timers are configurable for pulse width modulated output, watchdog timer, event counter, frequency measurement, pulse width measurement, period measurement, or one shot pulse output. The four 16-bit counters can also be configured into two 32-bit counter/timers.
-
product
High Speed Digital Analog
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
product
Simulation Tools for Analog and Power Electronics
SIMetrix
Complete mixed-mode simulation package providing high performance, ease of use and superior analog convergence.
-
product
Analog Multitesters
Sanwa Electric Instrument Co., Ltd
An electronic measuring instrument that combines several measurement functions in one unit. A typical multimeter can measure voltage, current, and resistance. Analog multimeters use a microammeter with a moving pointer to display readings.
-
product
Temperature Input Module For Remote I/O
The Temperature Input Module for Remote I/O features a features a thermocouple input range of ±100 mV and a voltage input range of ±5 V. It also has an adjustable filter time for improved measurement quality and optional external CJC or PT100 RTD measurements.A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the Temperature Input Module for Remote I/O from a real‐time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low‐cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high‐speed or specialty measurements.
-
product
Analog IC test system
A paradigm shift has been occurred in Japan’s major brand WL25 series tester. Ultimate simple system is available by effective analog pin architecture.This cost performance system is covered analog IC extensively, which are high accuracy, speed and multi-site test function.
-
product
Static Digital I/O Instrumentation
High-speed and static 3U and 6U PXI and PCI digital I/O instrumentation. Offering test rates to 200 MHz and programmable logic levels of -10 V to +15 V, our digital products feature the highest performance and most cost effective digital test solutions in the industry.
-
product
Digital I/O
With digital I/O cards, static or dynamic bit patterns can be generated or recorded. Each bit is assigned a control signal for an output and a sensor signal for an input. The usual voltage range for the inputs and outputs is between 2 V (TTL) and 24 V (automation).
-
product
Expansion I/O Module.
SI-MOD66xx
The SI-MOD66xx is a family of high resolution, multi function data acquisition and control modules that plug into any SI-CxDSP carrier processor card for the PCI bus.
-
product
DG I/O Backplane Extender Board
9286-1015
15" x 15" Backplane Adapter. Not to be used in production environment. Used with any I/O bus adapter during installation of Hawk system. Presents Nova/Eclipse bus signals on dual 50-pin connectors. Two 10 ft. (3 m) ribbon cables included.
-
product
Analog Backplanes
MSXB 030
Analog Backplanes provide expansion slots to accommodate compatible analog external boards. Analog Backplanes are passive, and connect all signals in each of the expansion slots in parallel. All expansion slots are identical
-
-
product
Analog DAQ Devices
Family of ruggedized products that provide an isolated analog, digital or temperature interface to a PC via the PC’s USB port.
-
product
Multi-Channel Clock Generator
XCLK1
Curtiss-Wright Defense Solutions
High-speed analog IO acquisition systems need a high quality master reference sample clock.Accurate synchronization in the 100MHz and up frequency domains is not easy and it’s a critical performance limiting factor if not done well. The XCLK1 multi-channel clock generator solves these problems.
-
product
Low Power Analog to Digital
7430
Smart A/D for thermocouples, thermistors, RTD's, strain and pressure gauges8-channels of 16-bit A/D resolutionEliminates trimpot adjustments by using software calibrationPerforms concurrent 32-bit floating point operations to minimize host computer loadingEach channel is software programmable for sensor type, gain, low-pass filtering, scan rate
-
product
PXI-6723, 13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module
778998-01
13-Bit, 32-Channel, 800 kS/s PXI Analog Output Module—The PXI‑6723 delivers low-cost, high-density analog outputs to meet a wide range of applications, such as stimulus-response, signal simulation, waveform generation, and actuator stimulation. In addition, the device provides eight 5 V TTL/CMOS digital I/O lines; two 24‑bit, 20 MHz counter/timers; and digital triggering and external clocking capabilities. The PXI‑6723 can replace several kinds of instruments, including stand-alone proportional integral derivative (PID) controllers, low-speed arbitrary waveform generators, and function generators. You can control each data point for each channel to define common waveforms, such as square, sine, or sawtooth, as well as complex waveforms.
-
product
I/O Wiring Cable
PCL Series
I/O wiring cable sets are designed for easy field wiring capabilities. The PCL-1050 I/O wiring cable series can be used with multiple I/O cards.
-
product
AS-Interface I/O Modules
*ClassicLine: I/O modules for field applications with quick mounting technology*CompactLine: I/O modules for field applications for harsh environments*SmartLine: I/O modules for control cabinet installations*ProcessLine: IP69K stainless steel modules for use in high pressure cleaning applications*Compact high-visibility illuminated pushbutton modules
-
product
PCIe-6535B, 32-Channel, 10 MHz, 40 MB/s Digital I/O Device
782629-01
The PCIe-6535 can continuously stream data over the PCI Express bus. It's an ideal solution for interfacing and testing image sensors or display panels. The module is also well-suited for other common digital applications such as pattern I/O, change detection, protocol emulation, or other custom digital interfacing. It features selectable voltage levels and per-channel directional control of the digital lines.
-
product
Advanced Programmable IO Board
MS 1508
- 32 Bit ARM9 LPC3250 Processor (256KB SRAM)- External memory (Flash – 2 MB, RAM - 512 KB, 8KB DPRAM)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 144 Digital IO Channels – (18 * 8 Configurable Ports)- 64 Analog Inputs (16 Bit, 1MSPS)- 16 Analog Outputs (16 Bit)- 2 RS232 Serial Ports- High Speed Logic Device with 1 M bit in system flash, 54Kbit - Block Ram and 11Kbit Distributed Ram- Power, Analog and Digital signals Interface Connectors (J1, J2 and J3 - 96 Pin Euro)- Data acquisition of all analog & digital channels- External Bus through Add on module (15 bit address bus and 16 bit data bus)- Transmission of 1Kbytes at 400us through Ethernet- Power Requirements: +15V/2.5A, -15V/2.5A and +5V/6A- Board Dimension is 366.72mm x 150mm- Portable and 9U 19” chassis mountable- Board has interface connectors in rear side as well as in front side- J1, J2 and J3 96 Pin Euro connectors at rear side and Ethernet, JTAG, RS232, USB connectors at front side
-
product
CB-68LPR, I/O Connector Block
777145-02
68-Pin Female VHDCI Right Angle to 68-Pin Female Screw Terminal, Desktop Mount Terminal Block - The CB-68LPR is a terminal block with 68 screw terminals for easy connection of field I/O signals to 68-pin NI data acquisition devices. It includes one 68-pin male connector for direct connection to 68-pin cables. This CB-68LPR features standoff feet for use on a desktop or mounted in a custom panel. The CB-68LPR also has a right-angle-mounted, 68-pin connector.
-
product
96 Sink/Source
YAV90096
Selectable voltage and current, comparation and measurement Drive sink or source up to 32 mA per channel Maximum voltage in output selectable from 9 to 24 VDC Possibility to use I7Os in parallel Pin voltage comparator with logic readout at fix +4VDC 10-bit resolution pin voltage measurement with CAN bus value readout Build-in editable test steps sequence (test script) Size: form G
-
product
Multi-Function PXI Card
GX3788
The GX3788 is a user configurable, FPGA-based, 3U PXI multi-function card which supports digital and analog test capabilities. The card employs the Altera Stratix III FPGA which features over 45,000 logic elements and 1.836 Kb of memory. The GX3788 is based on the GX3700 FPGA card and includes an integral daughter board which provides (8) differential input, 16-bit, 250 MS/s A to D converters and (8), 16-bit, 1 MS/s, D to A converters. The module's FPGA is pre-programmed, providing access to all digital and analog functions. Alternatively, users can program or modify the FPGA , allowing user to adapt the module to their own specific test needs. The design of the FPGA is done by using Altera's free Quartus II Web Edition tool set. Once the user has compiled the FPGA design, the configuration file can be loaded into the FPGA directly or via an on-board EEPROM.
-
product
Ethernet 48-Channel Digital I/O Interface
2410
Controls/monitors 48 digital signals over Ethernet PWM output mode Programmable input debounce Input edge detection with asynchronous host notification Compatible with standard solid state relay racks Embedded HTTP and Telnet servers Open source API
-
product
Analog VOM
260-8 & 260-8P
Nothing beats a Simpson 260-8 for monitoring fluctuating trends and rates. Portable yet with benchtop accuracy, the 260-8 is ideal for use anywhere -- workshop, lab or in the field. The 260-8P features an additional resettable overload protection circuit and audible continuity checking. Both versions come with batteries, manual and full-size test leads with threaded probe tips and screw-on alligator clips.
-
product
Digital I/O Products
Digital I/O series products provide computer monitoring of digital input and digital output signals for control of industrial devices through solid state relays.
-
product
High-Speed Analog Output
High-speed analog output photocouplers (optocouplers) are optically coupled isolators containing a GaAlAs LED on the input side and a PIN photodiode and high-speed amplifier transistor on the output side in a single chip.
