Electrical Field
space around an electrically charged object. Also known as: E-Field
See Also: E-field, Electric Field Probes
-
Product
Field Strength Meter
DIGI-FIELD
-
Measuring radio frequency and microwave radiation has never been easier! This unit covers the amazing range of DC - 12 GHz and will give you digital readout of the relative field strength of broadcast signals such as cellular phone, microwave oven leakage, TV station, CB radios using the (1MHz - 1GHz) telescoping antenna provided.
-
Product
Electric Servomotor Packaged Cargo Compression Tester
-
It is a testing device that can perform compression evaluation test of packaged cargo equipped with an electric servo motor type actuator.
-
Product
ELECTRICAL TEST Kit
1021 TK
-
Standard Electric Works Co., Ltd
2950 CL ● Pocket size.● 4000 counts.● Full automatic measurement : Voltage measurement. Current measurement. Resistor measurement.● Data hold function.● Continuity check.● Diode measurement.● Select function.● Low battery indication.● Auto off function.● Flashlight (auto off in 1 minute). ALS-2 ● Use with any clamp meter.● x10 mode allows for more accurate measurements of low amperage devices.● x1 mode allows for direct reading.● 4mm voltmeter input jacks.● Integrated ground conductor.● 10 amp capacity.● 10cm plug cord for greater flexibility.
-
Product
Embedded DisplayPort Electrical Performance and Characterization Toolset Software
D9040EDPV
-
Characterization testing of eDP designs now supporting AUX channel automation.
-
Product
Multifunction Meter for Electrical Installations
AMPI-525
-
*Short circuit loop measurement:*Impedance measurement with 23 A (44 A phase-to-phase), short circuit resistance RZW =10Ω*Measuring range: 95...440V, frequency 45...65 Hz*Short circuit loop measurement with resolution 0,01 Ω , without tripping the differential protections (I∆n ≥30mA)*Automatic short-circuit calculation, phase-neutral and phase-phase voltage detection
-
Product
Electrical Testing
-
Innovative Testing Solutions, Inc.
Our specialty is Direct Current automotive components. We perform product validation and design verification testing on both electrical components and systems. Also, we perform warranty investigation testing and failure analysis. We have voltage capabilities to 300 volts and current capabilities to 1000 amperes. Both two-wire and four-wire resistance measurements are supported from NanoOhms to GigaOhms.
-
Product
Magnetic Field Sensor
-
Vernier Software & Technology, LLC
The Magnetic Field Sensor can be used to study the field around permanent magnets, coils, and electrical devices. It features a rotating sensor tip to measure both transverse and longitudinal magnetic fields.
-
Product
Magnetic Field Press Device
-
Sometimes, magnetic application technology that can achieve results that push the limits of your products. Magnet-related equipment plays an important role in various fields such as electronics, metals, and physics.
-
Product
Field Intensity Meter
LM870-W
-
Sichuan Jiuzhou Electronic Technology Co.,Ltd
* Trunk-line AC voltage, V/A, C/N and TILT measurable* Automatic over-voltage shut-off protection* AC/DC optional (Ni-H/Li storage battery inside)* Full-digital key-board operation, direct freq. & channel input* Automatic scanning, Automatic channel-filtering, Automatic error-operation amending* All standard channels and subjoin channels pre-set inside* New channel-table setting according to user's special requirement* Spectrum displaying* English/Chinese operation interface* Audio output (speaker set-in)
-
Product
Field Test Kit
621
-
TESCO’s light-weight, 50 Amp Field Meter Test Kit (Catalog No. 621) with Power Factor, has been designed to reduce the weight of field test equipment to the lowest possible limit. The carrying case is fabricated from durable powder coated aluminum. The total weight of the meter test kit including leads, and digital reference standard is only 25 lbs! The test kit also incorporates ample storage space for the cable set.
-
Product
12V 0-500 Amp Carbon Pile Battery Load Tester and 12/24V Electrical Systems Tester
6042
-
• Test batteries up to 1000 CCA• Interprets data from the charging/starting system on easy-to-read LCD displays• Shows positive and negative amps for easy diagnosis of current leakage problems• 0-500 Amp variable carbon pile load tester• Unique curved carbon discs ensure maximum contact, fewer hot spots, smoother operation and longer life• Heavy-duty single extruded leads for testing up to 15 feet apart• Test electrical systems on 12/24 Volt systems• Test all battery types• Ideal for testing remotely mounted batteries accurately• INCLUDES: Model 6043 1000 Amp AC/DC Inductive Amp Clamp for checking starter draw or parasitic drain test, also can be used with conventional multi-meters; heavy duty, two wheel tilt-back cart with 8” wheels and 2 trays.• Made in USA of US and Global Components
-
Product
Electrical Motor Control
-
For more than 60 years, AOIP is specialized in the starting and control of asynchronous cage or slipring motors over any kind of equipment and in any weather conditions.
-
Product
Electrical Tester
T6-1000
-
The Fluke T6-1000 Electrical Tester with FieldSense™ technology lets you quickly, safely take True rms voltage and current measurements without test leads.
-
Product
Portable Three Phas Multifunction Electric Meter Calibrator
GF312V2
-
Beijing GFUVE Electronics Co.,Ltd.
GF312V2 portable three phase multifunction energy meter calibrator is with comfort design, small size, and light weight. It is suit for electric power departments, measuring and quality examining departments and electric lab to field use.
-
Product
Electrical Safety Analyzer
Model 19032/19032-P
-
Electrical Safety Test (EST) Analyzer that combines the functions of impulse test, hipot, insulation resistance and DC resistance measurements. It has 5kVac/ 6kVdc high voltage output, 5kV insulation resistance, 6kV layer short impulse voltage and 4-wire DC resistance measurement that can comply with the wound components test demands by providing maximum 10 channels output for multichannel scanning tests to save time and labor costs.
-
Product
Near Field Probes
-
A typical emi emission test is performed using broadband EMC antennas such as biconical, log periodics, Combilogs and horns. These antennas usually placed at 1, 3 or 10 meter distance as required by the test specification. These is considered far field measurements and the emission limits are given for the specific distance by the specification. During EMI compliance measurements, the emissions levels from products are compared with these limits. If the product exceeds these limits it is considered failing. These tests are typically conducted in a open area test site IOATS) or inside an anechoic chamber.
-
Product
Search Coils And Field Measuring Coils
-
Designed to measure the magnetic flux on magnets or in the airgap of magnet systems.
-
Product
Electrical Receiver Conformance Test Application for OIF-CEI 4.0
M809256CB
-
OIF-CEI 4.0 receiver test application for OIF-CEI 56G very short reach, medium reach, and long reach PAM4.
-
Product
Infrared Camera for CO Detection and Electrical Inspections
FLIR GF346
-
The FLIR GF346 optical gas imaging camera detects carbon monoxide (CO) and 17 additional gases without the need to interrupt your plant's production process. CO emissions can be a significant threat to primary steel manufacturing operations; even the slightest leak in a vent stack or pipe can have a devastating effect. With the FLIR GF346, inspectors can scan large areas from a safe distance, pinpointing leaks in real-time, reducing repair down-time, and providing repair verification.
-
Product
Single Position Automated Electric Fluxer
-
Single-position fully automated electric fusion machine with a typical sample throughput of 5-7 samples per hour. Ideal for preparing fused beads for XRF analysis and solutions for AA, ICP, and wet chemistry analysis. Patent PendingTypical samples include: Cement, Clinker, Ores, Slag, Refractories, Ceramics, Catalysts, Glass, Rocks, Minerals, Soils
-
Product
Electrical Safety Test Scanner
19200
-
Support Electrical Safety Test Scanning Support High / Low voltage circuit insulation (Switch module)Support 8 slots for plug-in (removable)Max. 9 slaves for multiple scanners (master/slave interface)Standard RS-232 and USB interface Optional GPIB interface CE Mark19200 can be installed in Chroma Electrical Equipment ATS model 8900
-
Product
Field Effect Rectifiers
-
ST field-effect rectifier diodes (FERD) help improve designs with new versions focusing on trade-off upgrades. Field-effect rectifier diodes belong to our STPOWER family. The design of the FERDs has allowed both a decrease in the voltage drop and a decrease in the leakage current temperature coefficient. As a result, the runaway safety margin is improved and maybe beyond the typical safety margin of Schottky barrier diodes.
-
Product
ECPR System (Electrically Calibrated Pyroelectric Radiometer)
Rs-5900
-
Developed in conjunction with NIST, the Rs-5900 ECPR is a ±1% absolute accuracy radiometric transfer standard for the visible to near-IR (0.25-2.0µm), with the RsIR Option extending the ±1% accuracy to >20µm. The RsP-590 Pyroelectric Probe requires no cooling and maintains ±1% accuracy from 1 µW to 100 mW. The ECPR uses an auto-nulling, electrical substitution technique that allows the instrument to be referenced against NIST electrical standards, insuring maximum accuracy and precision. Unlike most electrically calibrated radiometers, there is a direct correlation between electrical and optical heating because the same material serves as both the optical absorber and electrical heating element.
-
Product
Power Frequency Magnetic Field Simulators
-
Suzhou 3ctest Electronic Co.,Ltd.
Power frequency magnetic field simulator is a special designed instrument with high reliability according to the features of the power frequency magnetic field immunity test for electrical and electronic products.
-
Product
Electrical Tomography Software
Res2dinv
-
This very popular software, developped by M.H.Loke, uses the method involving the Sasaki minimum squares inversion (1992) to produce a 2D sub-soil model starting from the data of apparent resistivity (up to 2000 electrodes). It is completely automatic and does not require that the user formulates a starting model. When using a state-of-art computer, the inversion of a single pseudosection will require only a few minutes.RES2DINV supports spreading types like Wenner, Schlumberger, Pole-Pole, Pole-Dipole, line Dipole, equatorial Dipole and other non-conventional spreading types.
-
Product
Electrical Development & Redesign
-
Your product description goes hereARC’s electrical engineering team has the leg up when it comes to developing or redesigning to your specific requirements.All the way from prototyping to cable design to integration, our talented team of clever engineers can deveop a prototype quickly and get your project off on the right foot. Whether it is a new solution or if you are redesigning an obsolescent FPGA system, our team can provide quickly and effectively while still keeping your budget in mind.
-
Product
Field-installation Type Electric Conductivity Meter (Two-Wire Transmission, For Low-concentration)
HE-300C
-
HE-300C connects conductivity sensor (ESH/FS Series) and measures conductivity and temperature in the sample water. It is suitable for monitoring pure water/boiler water drainage recovery control and inline measurement of pharmaceutical water conductivity according to USP<645> quality guidelines.
-
Product
Electromagnetic Field Analyzer System
-
A compact size electric antenna (The electric field analyzer system) that hasthe spectrum analyzer function. This instrument is most suitable to the radiation noise measurement ofelectric field from the system, such as the wireless power supply, that uses the frequency less than 30 MHz.
-
Product
Impact Echo SystemFor Field Evaluation of Concrete Structures
Vu-Con System
-
The Vu-Con Analyzer provides the engineer with the sturdiest, most reliable system for impact echo analysis. No moving parts and implementation of the latest microcomputer technology has created a system that is both sophisticated and reliable. The unit comes with a 90 mm (3.5?) by 115 mm (4.5?) graphic display screen that is easily viewed in daylight
-
Product
Electrical Standards
-
To verify the performance of an electrical calibrator or dc calibrator, you need an electrical standard. Fluke Calibration standards are found in primary calibration laboratories across the world. A wide range of electrical standards and frequency standards are designed to meet the needs of today’s laboratories for traceability and quality accreditation while also being portable, simple to use, and easy to support. Electrical standards include: Voltage standards; ac/dc transfer standards; ac measurement standards; resistance standards; ratio standards; current shunts.
