Button Cell
single cell battery 5-20 mm round and 1-6 mm thin.
-
Product
Button Load Cell
3000 Series
-
Button Load Cells are strain gage based transducers with temperature compensation and excellent overall performance. This type provides a range of capacities up to 150 kN or 30 klb with better than ±0.5% (full scale) non-linearity. Three tapped holes are provided on the underside for ease of mounting. Fully welded cover, amplified and digitised versions are available on request.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting Holes
LBC SERIES
-
The LBC Series (Load Button) load cells are offered for compression only applications where space is limited. The matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Counter bored mounting holes are provided for fastening down from the top. These sensors are manufactured from heat treated 17-4ph stainless steel and sealed for use in most industrial environments.
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting
LBM SERIES
-
The LBM Series (Load Button) load cells are offered for compression only applications where space is limited. This load button is a direct replacement for many of the same type and bolt patterns currently used in the industry. The matching surface must be flat and at least 2 inches in diameter. The loading diameter is slightly convex for accurate load distribution. Eight threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
Product
Cable Tracers
179 CB
-
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
Product
Portable DAQ & Signal Analyzer
ObserVR1000
-
Vibration Research Corporation
Collect data with the press of a button using the battery powered ObserVR1000 hardware and a mobile interface. Stream to the SD card while running other test modes, or use independently as a field data recorder and analysis package.
-
Product
Tire Pyrometers
52-50640
-
Longacre Racing Products, Inc.
Accurate, super-fast response electronics.Can hold highest temp reached. Compares one temp to another with the push of a button. Low battery indicator and auto shut-off. 2000 Range (tire probe max 500). F or C switchable. Standard coil cord tire probe and carrying case included.
-
Product
Pocket Digital Multimeter
HH0305
-
Basic accuracy0.5%. Large LCD display 2000 count. Auto Ranging with manual range selection availability. Higher Voltage test up to AC600V and DC 600V. Higner current test up to 200mA DC. Resistance test up to 20MΩ. Diode test and Continuity Check. Data hold function. Using 1x1.5V LR44 (AG13) button batteries. Size: 120mm x 70mm x 18mm
-
Product
Cable Tracers
181 CB
-
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
Product
Load Button Load Cells
-
Interface’s load button load cells are designed for customers who require the measurement of compression forces in a very low height space. They are designed to provide the most accuracy in as little space as possible. The smaller ConvexBT or LBMU can fulfill the need for force measurements at a very respectable precision level that is enough for most applications. Diameters range from ⅜ of an inch to just over 3 inches, with heights from ⅛ of an inch to 2 inches. The shaped load button has a spherical radius to help confine misaligned loads to the primary axis of the cell.
-
Product
5V1mA Button Battery Tester
TOB-BST8-5V1mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channel Battery Analyzer (0.002-1mA, up to 5V) with Laptop & Software for R&D Battery Materials. TOB-5V1mA Button Battery Tester is an eight-channel battery analyzer to analyze small coin cells with a range current 0-50mah, voltage 0-5v. Each channel of the analyzer has independent constant-current and constant-voltage source, which can be programmed and controlled by computer software.
-
Product
Cable Tracers
180 CB
-
Standard Electric Works Co., Ltd
● The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.● Works with any Tone Generator to identify wires.● Volume control for increased sensitivity and adjustable to suit work environment.● Recessed ON/OFF button prevents battery drain.● A phone jack is designed for headset or handset.
-
Product
Infrared Array Sensor
Grid-EYE Evaluation Kit
-
Panasonic Automotive & Industrial Systems Europe GmbH
Panasonic Automotive & Industrial Systems has launched this evaluation kit for its Grid-Eye infrared array sensor, which integrates a ”nanopower” Bluetooth Smart module and a microcontroller. The kit is intended for prototyping the Grid-EYE sensor which is a 64 pixel IR camera in a surface mount package measuring 11.6mm x 8mm x 4.3mm, which integrates the MEMS sensor, lens and I2C interface. The integrated Bluetooth module in the evaluation kit, the PAN1740, draws 4.9mA in transmit or receive operating modes, which means it can be powered by coin cell batteries. The IR sensor has 64 thermopile elements in an 8×8 grid format that detect absolute surface temperature without any contact.
-
Product
Food Thermometer
KM 6503
-
Kusam Electrical Industries Limited
• Temperature Range : -50°C ~ +300°C (-58°F ~ +572°F)• Temperature unit °C / °F changeable.• Data Hold Function• Power Supply : 1.5V x 1 button cell Battery.• Accessories : User Manual, Battery & Plastic tube packing
-
Product
Low Profile Compression Only Load Button Load Cell with Mounting
LBO SERIES
-
The LBO Series (Load Button) load cells are offered for compression only applications where space is limited. Matching surface must be flat and at least the diameter of (D1). The loading diameter (D2) is slightly convex for accurate load distribution. Threaded mounting holes are provided on the bottom surface for fastening down from beneath. These sensors are manufactured from heat treated 17-4phstainless steel and sealed for use in mostindustrial environments.
-
Product
Shore A Durometers
PHT-960
-
Measuring range: 0-1000HSA (0-100 HSD)Deviation: <1%HResolution: 0.5HDigital read outAuto Hold featureAccurate and repetitive deviation = 20~90HSAHSA<+/-1 gradeUses 1-SR44 Button Cell BatteryCustom rugged carry case
-
Product
Battery analyzer For Coin Cell 5V20mA
TOB-5V20mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels Battery Analyzer (0.1-20mA, up to 5V) Lithium Coin Cell Battery Research. TOB-5V20mA Battery analyzer is an eight-channel battery analyzer to analyze small coin cells with a range current 0-20mah, voltage 0-5v.
-
Product
Heavy-Duty Continuity Tester
TE6-0710
-
Hangzhou Tonny Electric & Tools Co., Ltd.
*Designed to test circuits while power is OFF*2- 1.5V Button cell batteries included. *Durable ABS housing.*High-quality materials for long-lasting durability.*Sharp tip for probing circuits.*Electrical Multi-Testers for almost any automotive repair on all 6, 12 , 24 and 48 volt systems.*Suitable for a broad range of household, car, trucks, boats, trailers, vans, motorcycles, industrial and commercial uses
-
Product
5V50mA Coin Cell Battery Test Equipment
TOB-5V50mA
-
Xiamen Tob New Energy Technology Co., Ltd
8 Channels Battery Test Equipment (0.1-50mA, up to 5V) For Lithium Coin Cell Battery Research. TOB-5V50mA Battery Test Equipment is an eight-channel battery analyzer to analyze small coin cells with a range current 0-50mah, voltage 0-5v. Each channel of the analyzer has independent constant-current and constant-voltage source, which can be programmed and controlled by computer software.
-
Product
Thermal Imaging
JOHO272
-
Wuhan JOHO Technology Co., Ltd
With innovative design and superior functions, this thermal weapon sight sets a new standard to build in an eye-safe laser ranger finder which you can get target distance very easily. The thermal aiming and laser ranging scale line would be changing smaller as distance further so that the shooter would easily and quickly lock target even in a further distance. To improve shooting percentage, as many as ammunition drop chart can be input to the sight program. Should any drop chart be selected, the sight would automatically generate a new shooting scale line after program calculating temperature, angle, wind speed, altitude. Different button size and battery convex design friendly for shooter night us
-
Product
Solid Oxide and Molten Carbonate Fuel Cell Test Stations
-
Greenlight''s SOFC test systems include options for integrated reformers, de-sox, gas mixing, water saturation, pre-heating, furnace, heat recovery and water balance. These SOFC test rigs can be configured to operate on gaseous or liquid fuels, with operating temperatures up to 1000C. Pressure control is optional and furnaces can be tailored for either planar or tubular cell configurations. For single cell or button cell testing, Greenlight offers the X20 table-top SOFC test bench, including furnace and optional fixtures.
-
Product
Resistivity Cell For N1413 (50 Mm Electrodes)
N1424A
-
The N1424A is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424A to the B2985B/87B.
-
Product
Resistivity Cell For N1413 (26/50 Mm Electrodes)
N1424B
-
The N1424B is designed to operate specifically with the B2985B/87B Electrometer/High Resistance Meter. It is used to measure surface or volume resistance/resistivity of insulation materials. The N1413A High Resistance Meter Fixture Adapter is required to connect the N1424B to the B2985B/87B.
-
Product
Holiday Detector
APS Holiday Detector
-
800 volts to 35,000 volts in one instrumentSafety cutoff switchDigital output displaySuper bright LED displayTwo volume SettingsRegulated voltageLarge push button controlsGreater battery efficiencyCompatible with Model AP/S1 & AP/S2 components and accessoriesOpen, ergonomic designTHREE YEAR WARRANTY
-
Product
Silver Button Sockets
-
For BGA, QFN, or LGA applications, GTP contact technology provides >94 GHz signal speed and can additionally be used in high cycle life applications such as ATE. These sockets support pitches from 0.2 mm to 1.27 mm. Ironwood's GT sockets are ideal for prototyping and testing almost any BGA device application. These IC sockets provide excellent signal integrity yet remain cost effective. Innovative elastomer interconnect technology that delivers low signal loss (1dB at 94GHz) and supports BGA packages with pitches down to 0.2mm was utilized in these sockets. GT BGA sockets are mechanically mounted over a target system's BGA lands using mounting and alignment holes at proper locations (page 2 of the individual socket drawing shows recommended PCB layout information). These low-profile sockets are only 2.5 mm per side larger than actual IC packages (industry's smallest footprint).
-
Product
Load Cells
-
Load cells are electronic weight sensors whose purpose is to receive the electrical excitation caused by a certain weight applied to the scale or balance and transmit it to a weight indicator . The load cell is an essential component in any scale or electronic balance and they come in different models and specifications. A Wim load cell is essential for a weighing system where precision, durability and a fair price are required. WIM-Systems manufactures a wide variety of load cell models, one for each need, in addition to offering all the advice you need to choose the model that best meets the particular needs of your weighing system and always backed by WIM-Systems quality and technology.
-
Product
Load Cells
-
Instron is the only testing system manufacturer that designs and builds its own load cells, ensuring exceptional accuracy, stiffness, and alignment across a wide measurement range. Produced at Instron’s High Wycombe, UK facility, each load cell is temperature-compensated and calibrated to international standards for outstanding repeatability. Backed by the largest commercial deadweight stack in the U.S., Instron’s calibration process delivers precision that often exceeds industry requirements—providing reliable, traceable performance for even the most demanding materials testing applications.
-
Product
load cell
EST-40
-
Technopark Automation & Control
The EST-40 is an 'S' type load cell suitable for use in tension and compression and is popular on hopper, tank weighing, belts scale and process weighing applications. It is low cost and is available in capacities from 50 kg to 2000 kg.
-
Product
Keyboard Button Testers
-
Infinity Machine International Inc.
Keyboard Button Testers by Infinity Machine International Inc. - for applications such as keyboard button compression force tester, keyboard durability test machine, adjustable keystroke life-span tester, mechanical keyboard switch tester, computer keystroke tester, button force testing, key stroke force tester for load stroke curve test, rubber keystroke tester, and more.
-
Product
Snap Button Pull Test Machine
UI-TX01
-
Snap Button Pull Test Machine is used to test pull strength of ornaments on garment, toy, footwear and others including button, bow and etc. Snap button pull test is a must-do test especially for Baby and children’s clothing and shoes. The test aims to use to button snap pull tester with suitable grips to pull the ornament to know if the ornament would be pulled off garment or not. The ornament falling off or broken button may cause infants or children the risk of ingestion. The button pull test methods includes 16CFR1500.51-53, ASTM PS79-96, ASTM F963, EN 71-1，M&S P115A and etc.
-
Product
Custom Button Stations
CueStation
-
Interactive Technologies, Inc.
The CueStation family of button stations are attractive, sophisticated and customizable -- perfect for use in projects that require a small panel of buttons that can control automated lighting, audio, show playback and other similar actions.Available in many different configurations, CueStations can be customized to fit nearly any project. Pick from digitally networked stations or simple passive switches, different button styles, LED options, housing colors, engraving options and much more.Use CusStations as a remote control accessory for our CueServer lighting automation processors or your own custom projects.
