Product

Standard VXI Module Shield Kits With Address Switch Opening

-

ICS Electronics

ICS Electronics

* Single-slot kit fits all VXI-1 Revision 1.0 to Revision 3.0 chassis.* Clamshell design fits C-size modules with 96-pin connectors.* Side shields include connector shrouds for maximum shielding.* RFI limiting, air vent slots along top and bottom edges for good air circulation thru the module.* Extruded front panel is bend resistant.* Address switch opening on component side shield.* Complimentary layout support includes PCB design template and CAD layout files.

Product

Standard Voltage 37 Pin D-Type Cables - Connector to Connector for Pickering

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connector to connector cable assemblies below are suitable to use with Pickering cards and modules that utilize a standard voltage 37-pin D-type connector.

Product

Standard Step Tablets, Gray Scales & Density Reference Charts

-

Applied Image, Inc.

Applied Image, Inc.

Standard Step Tablets, Gray Scales & Density Reference Charts are available in a wide variety of patterns, designs and sizes to fit a multitude of today’s application needs. Our gray scales and density patches are measured on a variety of NIST traceable instrumentation, including some of the most sophisticated microdensitometers available to the industry. They are imaged on either Photo Paper (RM) or Film (TM) to function for reflective or transmissive applications.

Product

HIGH FREQUENCY DC BIAS

6565 SERIES

-

Wayne Kerr Electronics, Ltd.

6565 SERIES - Wayne Kerr Electronics, Ltd.

The 6565 HF DC Bias Unit is intended to be used with a Wayne Kerr 6500 analyzer, either the 6500B Precision Impedance Analyzer or the 6500P HF LCR Meter. Its function is to provide a source of DC bias current through the Device Under Test (DUT) while the analyzer is making AC measurements. Each 6565 unit can provide up to 10 A of DC current, and up to six 6565 units can be connected in parallel to supply a maximum 60 A. A digital ammeter on the front panel allows the user to see the dc bias current value and an indicator LED shows when the bias current is enabled.

Product

Standard M12 Cylindrical Photoelectric Sensors

-

Contrinex AG

Contrinex AG

Contrinex Standard M12 Cylindrical Photoelectric Sensors

Product

Additional Products: Standard Voltage 9 Pin D-Type Cables - Connector to Connector

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connector to connector cable assemblies below are not compatible with Pickering products, however, are offered for developing a connection solution for use with other products.

Product

Viscosity Standards

-

Ametek Brookfield

Ametek Brookfield

Brookfield Viscosity Silicone and Oil Standards provide a convenient, reliable way to verify the calibration of your Brookfield laboratory viscometer/rheometer.

Product

Frequency Counter, 30MHz to 800MHz, 500MHz to 2.8GHz, 7 Digits

72-7390

-

Tenma

72-7390 - Tenma

Rugged instrument is smaller than a deck of cards, yet provides frequency measurement of digital, on/off keying and analog signals from 30MHz to 2.8GHz. It is perfect for displaying the output of two–way radio equipment, analog and digital cell phones, RF remote controls and many other items. Internal vibrator alert also makes this an outstanding device for detecting transmitters in counter–surveillance applications

Product

Standard M18 Cylindrical Photoelectric Sensors

-

Contrinex AG

Contrinex AG

Contrinex Standard M18 Cylindrical Photoelectric Sensors

Product

High Frequency Clock Divider Board

-

Alliance Support Partners, Inc.

Alliance Support Partners, Inc.

Clock Divider is designed to divide high frequency signals, up to 2.5GHz, from 4 to 256 times. It will accept single ended (Unbalanced) or differential (Balanced) signals with amplitudes as little as 100mV rms. The clock division is controlled by 4 shunt jumpers. The circuit can be disabled and the divide by counter reset with 2 control signals. The on board regulator will accept voltages from 4.85 to 15.0V. The output is capable of driving 700mV Peak to Peak into 50 Ohms.

Product

Primary Standards

-

Mensor Corp.

Mensor Corp.

Primary standards (often also referred to as mechanical dead-weight testers, pressure balances or primary pressure standards) are the most accurate reference instruments for pressure. Their functional principle is based on the physical principle of pressure = force/area. Mass pieces placed on the top of a piston-cylinder system are the source of a precisely defined force. By producing a certain (counter) pressure inside the primary standard an equilibrium is achieved: the mass pieces, including the free-running piston of the piston-cylinder system, are floating, which will lead to a very accurate pressure at the test port which measured through piston gauge technology.

Product

Standard

-

Quartzlock (UK) Ltd.

Quartzlock (UK) Ltd.

RF Distribution Amplifiers

Product

1.3GHz Frequency Counter

Model 1122 / 1122X

-

Aplab Limited

Model 1122 / 1122X - Aplab Limited

- Wide Frequency Range 0.2Hz to 1.3GHz- 2 Separate Channels, for LOW & HIGH Frequencies- High Sensitivity- 8 Digit Green LED Display- Microcontroller based Advance Technology- Optional RS232 Interface- Reciprocal Counting Technique for High Resolution at Low Frequency- Period Measurement- Low Pass Filter for Noisy Low Frequency (<100KHz)- 4 Selectable Gates (10ms, 100ms, 1sec, 10sec)