-
Product
Total Nitrogen Unit For TOC-L Series
TNM-L
-
Perform simultaneous TOC and TN measurements. *720 °C catalytic thermal decomposition/chemiluminescence methods are adopted for TN measurement. There is no interference from metallic ions or bromine in sea water.*Measurements over a wide range with a detection limit of 5 μg/L for TOC-LCH to an upper limit of 10,000 mg/L.
-
Product
LXI Matrix Switching Unit
ProDAQ 6140
-
The ProDAQ 6140 provides a relay matrix which can be fitted between the sensors and actuators on a device under test and the data acquisition and control system. It allows to separately connect/disconnect the signals from either side and to connect them to an internal bus. In this way signals can be routed via the bus to new destinations or the bus can be used to monitor or supply test signals. This allows calibrating and debugging the system without disconnecting and separating channels throughout the system wiring.
-
Product
FREQUENCY DISPLAY UNIT
TYPE NFD-1
-
The National RF Type NFD-1 Frequency Display Unit was designed for use with vintage and classic communications equipment, to display the received or transmitted radio frequency. The unit incorporates an internal processor that allows the intermediate frequency (IF) to be counted out by the frequency counter. The resultant display is the actual frequency that the equipment is receiving or operating at.
-
Product
2U, 4U, and 6U Developmental RF Interface Units
1257A-D
Interface
The Astronics 1257A-D is a sixth-generation RFIU design. It comes with a new easy-to-use LXI Core 2011-compliant device and new enhanced features, including the ability to acquire all of the components you need to assemble your own unit in-house, reducing your design time.
-
Product
SM / Expansion Unit
-
A testing procedure designed to thoroughly test the electrical characteristics of a wire or cable, may require additional test points to connect the end points of all conductive paths. The changing and alteration of Test Adapter Cables (TACs) would become obsolete when having access to one or several expansion units. Increased testing efficiency alleviates the long, drawn out down times of the disabled aircraft while improving product readiness. Additional time can be spent on troubleshooting and problem identification and will not require the user to unhook and connect TACs to different matrices. Adding additional expansion units will save the user time, money, and effort.
-
Product
DC BIAS CURRENT UNIT
3265B SERIES
-
To evaluate components at currents up to 125 A the 3265B DC Bias Units are used with either the Wayne Kerr 3255B series of Inductance Analyzers or the 3260B Precision Magnetics Analyzer. When one 3265B/25A or 3265BQ/25A DC Bias Unit is connected to an instrument up to 25 A of DC bias current can be set in steps of 25 mA with one unit. Additional DC Bias Units can be added such that with five units connected in parallel it is possible to set DC bias currents up to a maximum of 125 A DC.
-
Product
Control Unit
-
Managing an RF test bench poses several challenges, Heterogeneous Instruments-Test benches comprise various instruments with different communication protocols (LAN, USB, RS232, etc.).
-
Product
Portable Units
-
The basic version for mobile conductivity measurement. It is a robust and intuitive portable device for routine daily measurements in laboratories and processes. Over 1,000 operating hours with a single set of batteries (4x AA).
-
-
Product
6x 3U OpenVPX MOSA Remote Interface Unit
SIU36-RIUVARM-01
Remote Interface Unit
SIU36-RIUVARM-01 is a Modular Open Systems Approach (MOSA) Remote Interface Unit (RIU) to manage, monitor and control connected I/O, communications, measurement and simulation interfaces through Ethernet commands from a main mission processors. Extremely low power with 2 x 10/100/1000Base-T Ethernet.
-
Product
Delay Unit
V972
-
The Mod. V972 is a 1-unit wide VME 6U module that houses a delay unit with a range from 0 to 31.5 ns with a 2.6 ns offset. The delay can be set in 0.5 ns steps via front panel toggle switches.
-
Product
AC-DC Rectifier Unit
-
Supreme Instrument Laboratories
Continuously variable/manually variable D.C. Rectifier unit to be used in the Electrical Engineering Laboratories, with the following technical specifications
-
Product
NON-CONTACT TEST COMPATIBLE Ultra High Speed Bare Board Tester System(ALL-IN-ONE UNIT)
SX-750SUPERⅣC
-
All-in-one Compact Size TesterAll-in-One type Tester, with built-in PC in the Tester main unitImproved operability with a 10.4" Touch PanelAll the operation screens are optimized for touch-pannel operation.
-
Product
Front Panels For Plug-In-Units | ATCA
Front-Panel-Plug-In-ATCA
-
EMC front panel for ATCA plug-in-units | 8 U x 6 HP | classic or ergonomic
-
Product
Manual Fixture Kit With Mass Interconnect Cassette Interface, Max number of probes (2N) 1000 units, Max UUT 450 x 330 mm (wxd)
CMCSK-07-01
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Calibration Units
-
Optical Stroboscope and Tachometer European Calibrator Unit was originally designed for in-house test and calibration of our comprehensive range of Digital Optical Tachometers, Optical Speed sensing products and Stroboscopes.
-
Product
Measuring Complex for Registration of Test Parameters of a Pumping Unit
-
Portable portable complex for measuring and recording parameters of factory testing of horizontal pumping units.
-
Product
Remote Terminal Unit (RTU) Replacement
-
Schweitzer Engineering Laboratories, Inc.
Compared with typical RTUs, SEL automation controllers provide improved reliability, extended I/O contacts, and advanced automation and control for remote substations and field applications.
-
Product
Control Unit
MX 256
-
Teledyne Gas & Flame Detection
The MX 256 is a digital control unit intended for the detection and measurement of gases present in the atmosphere and more generally for the processing of any digital signal from digital sensors (OLCT 10N types), relay module, analog output module, logic input module. Thanks to its new option, an industrial controller module or remote HMI, it is possible to add analog input modules for sensor-transmitter connection (4-20 mA) and / or relay modules, this allows to not only extend the capacities but also to have event recordings (Location, Alarms,.....) and to have access to the data via the embedded web page.
-
Product
12-Ch 10A-250VAC RCV Power Distribution Unit
YAVAR438
Switch Module
- Hardware controlled Enable Input- 12 Power relays up to 10A 250VAC/DC and 300W or 2.700VA switching power- 12 10-mOhm shunt resistors.- 6 Switched 2-Pole sense channels- Single phase isolated or 3-Phases non-isolated switching capabilities, to or from the device under test (power or load)- VPC TriPaddle 96 pins connector.- NI LabView & TestStand driver.- .NET, C/C++, VB driver.- Soft Front panel for direct interface.- CAN Control or Ethernet (with Ethernet to CAN Gateway).- Self-test module available.- Form A
-
Product
High Power, Low PIM Switch Unit
LPSU series
-
LPSU series high power, low PIM switch units combine 65 low PIM ports or 14 low PIM ports. These switch matrices are designed in testing situations that require multi-band PIM sources, components or antennas. Combinations of multi-band PIMtesting are now easily possible, improving workflow significantly. LPSUs can be integrated in existing production control systems. Frequency range 698-2700 MHz.
-
Product
Scale Units
-
* Designed to be installed on the machines and fixtures to measyre the axial movement.* Can be connected with large LCD display unit easy reading.* Zero-setting at any position.* Data output.
-
Product
Multi-Channel Attenuation Control Unit (5-channels), DC to 18 GHz, 0 to 121 dB, 1 dB Step
J7205B
Attenuator
The J7205B is a multi-channel (5-channels) attenuation solution for signal attenuation and conditioning of up to 5 devices under test (DUT). Operating frequency from DC to 18 GHz, with 121 dB, 1 dB steps. Exceptional 0.03 dB insertion loss repeatability per section for the entire 5 million cycles and excellent attenuation accuracy and flatness, the J7205B reduces cost of ownership and provide the best measurement accuracy.
-
Product
Energy Measuring Units
-
Mitsubishi Electric Automation, Inc
Energy measuring units to support energy saving at workplaces.These units support to monitor consumption energy precisely, which is necessary for reducing energy cost. By combining with Split-type current sensor, you can easily fix in equipments which you want to measure.
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMK-04
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
ME2PWG-B, Pneumatic Unit
101506
-
The ME2PWG-B is a cutting-edge pneumatic unit from the ME2 series that showcases remarkable versatility and efficiency. This interchangeable system consists of the ME2PWG basic unit and the ME2PWK exchangeable cassette, making it a robust choice for a variety of applications. It incorporates an innovative auto-open function that facilitates both manual operation and an optional fully automated auto-open-close feature, ideal for use in restricted or secure environments. With an impressive opening angle of 90°, users can easily transition between manual control and robotic automation, enhancing operational flexibility and speed.
-
Product
1RU Automated Switch Unit
UC1
-
Universal Switching Corporation
The UC1 switch system provides a modular solution for a variety of signals up to 50GHz, and is designed for smaller requirements. This product delivers ultra-high signal performance coupled with advanced remote/manual control and monitoring with 10/100 LXI certified Ethernet port, multi-serial port, front panel control, direct alarm input port, and auto-sense (on some PUC's).
-
Product
128 DIOs JTAG Boundary Scan Resources Unit
YAV9JTAG
Test Fixture
Boundary-scan is a widely practiced test methodology that is reducing costs, speeding development, and improving product quality for electronics manufacturers around the world. By relying on an industry standard, IEEE 1149.1, it is relatively quick, easy, and inexpensive to deploy a highly effective test procedure. In addition, today’s PCBs have little alternative because of limited access to board-level circuitry.
-
Product
Storage Unit
DM-U.2
-
The DM-U.2 PXI Express Storage Unit provides up to 7.68TB of removable solid state storage (SSD) in a single PXI Express slot. It addresses the requirements of users who need to remove and replace PXI Express storage for security or other reasons. This includes data recording applications where recorded media must be quickly removed and replaced with fresh media between recording missions. It also facilitates easy data removal for data security reasons when a system is left unattended.
-
Product
PXI-4130, ±20 V, ±2 A DC, 40 W PXI Source Measure Unit
779647-31
Programmable Power Supply
±20 V, ±2 A DC, 40 W PXI Source Measure Unit - The PXI‑4130 is a programmable source measure unit (SMU). It has a single isolated SMU channel that offers a four-quadrant output that incorporates remote (4‑wire) sense. With its five current ranges, it is ideal for transistor characterization that requires accurately sourcing a constant current or voltage while sweeping another current. The PXI‑4130 also includes a utility channel that can source either current or voltage. This PXI SMU can act as either a constant voltage source or a constant current source, with a settable compliance limit for either mode. In addition, you can enable remote sense on the SMU channel to maximize voltage output and measurement accuracy on your device under test (DUT) for high-precision applications.
