Tachometer Testers
See Also: Tachometers, Engine Tachometers
-
Product
Tachometers
-
Is an instrument measuring the rotation speed of a shaft or disk, as in a motor or other machine.
-
Product
Advanced Handheld Tachometer
FT-7200
-
The FT-7200 Advanced Tachometer is an easy-to-use handheld digital tachometer offering high functions and performance. The use of FFT (Fast Fourier Transform) technology enables the FT-7200 to perform frequency analysis of rotation speed by using change of signal in sound, vibration or magnetic flux from rotating machines such as a motor or the like. Selection from 5 kinds of measurement modes allows it to calculate and display rotation speed of any complex waveform signals from a sound level meter or an accelerometer accurately by extracting the exact frequency component.
-
Product
Testing Aircraft Tachometers
-
The test bench is comprised of a TMB 304 Torque Transducer and a custom fixture for the tachometer and corresponding inertia wheel. A servo motor is incorporated to provide speed to the tachometer. The entire drive train is conveniently mounted on a base plate with the appropriate couplings, bearing support and flywheel.
-
Product
Tachometers
-
These instruments are widely accepted among mechanical or certification centres, to measure revolutions (RPM) and rotation speed.
-
Product
Tachometer
F90 Series
-
* DIN Size 48 X 96 mm * High precision measuring from low-speed to high-speed by 1/TAU method * With Prescale Function * Auto-Voltage, 100 to 240 VAC
-
Product
Handheld Tachometers
-
The handheld tachometer is a means of measuring revolutions within the industrial sector, either optically or mechanically. The handheld tachometer can be used for maintenance and calibration of machines that have moving parts. The principle is similar to a bicycle speedometer, where time will be measured until a wheel has completely turned. The handheld tachometer has two different measurement methods.The handheld tachometer may have a contact connection to the moving parts. Alternatively, the handheld tachometer works with reflecting marks. This will be secured on the moving part. As the laser strikes the reflecting mark during rotation, it will be reflected and detected in the handheld tachometer via a sensor. Rotation speed and speed can be seen on the handheld tachometer. The handheld tachometer may combine both possibilities (contact and non-contact connection). Next to the handheld tachometer you find other devices for measuring revolutions at PCE Instruments.
-
Product
Digital Non-Contact Tachometer
TACH2
-
UEi Test & Measurement Instruments
The TACH2 is a dual measurement mode, contact or non-contact, Tachometer that measures rotational speed using both modes. With measurements of RPMs up to 99,999 are possible, with resolution automatically changing throughout the range.
-
Product
Tachometer Generators
-
Citizen Chiba Precision Co., Ltd.
*Compact, high functioning and high reliability *Minimal ripples in output voltage *Superior linearity
-
Product
Optical Tachometers
-
PeakTech Prüf- und Messtechnik GmbH
Enables fast and accurate contactless measurement of the rotation per minute and the surface speed of rotating objects.
-
Product
Gasoline Engine Tachometer
SE-2500A
-
SE-2500A is a non-contact handheld tachometer designed for gasoline engine measurement. Detection, measurement, and display parts are all in one unit and batteries are built in the unit. Moving the detector (head of the SE-2500A) close to an ignition coil can measure rotation speed at the unit of 1 r/min or 0.01 r/s. Up to 20 measurement data can be stored in the internal memory that is convenient for later checking.
-
Product
Digital Tachometers
-
Shanghai Beha Electronics Co., Ltd.
*Optical and mechanical measurement Rotation speed*Digital Tachometer for accurate determination for revolution*Counter function
-
Product
Limited Angle Torque Motors and Tachometers
-
CAES offers limited-angle torque motors in a wide variety of catalog sizes, with cog-free motion in a limited range.
-
Product
Strobes & Tachometers
-
Imada is proud to introduce a line of speed measurement instruments from Hoto Instruments. Stroboscopes can be used to measure the measure the linear rotational speed of rapidly rotating objects. Imada also offers a digital tachometer / lengthmeter. The tachometer / lengthmeter measures speed or revolutions and features exceptional accuracy even at low speeds. The tachometer can be paired with an optional 12″ wheel to measure the surface speed of conveyer belts and similar machinery.
-
Product
CONTACT CUM NON CONTACT DIGITAL TACHOMETER
IBL-DT2236
-
International Biological Laboratories
This is a digital contact cum Non Contact combined, Hand Held Tachometer.
-
Product
Tachometers
AP1000
-
Features • Field programmable • Displays rates from 0-9,999 or time-in-process • Simple installation, panel mount meter • Bright 0.3 inch high efficiency LED displays • ETL approved to applicable UL and CSA standards • Standard input power is 115 VAC; 230 VAC and 12 or 24 VAC / VDC are optional.
-
Product
Pro Laser Tachometer
332
-
The #332 is the ideal tool for easy and accurate measurement of RPM in almost any environment. Simply aim the laser beam at a reflective mark placed on a rotating device, push the button and the RPM reading is immediately displayed. No contact with the shaft or wheel is necessary. The laser beam is not affected by shop light and can detect RPM from longer distances of up to 6 feet away. The #332 can measure up to 99,999 RPM in 1 RPM increments. It can be used to measure RPM on coil-on-plug and diesel engines, where conventional inductive tachometers can not be used. Other uses include generators, compressors, industrial engines, fans, gears and more. Zippered case, reflective tape, instructions & 9V battery included.
-
Product
DIGITAL TACHOMETER
IBL-DT2234C
-
International Biological Laboratories
This Hand Held Non Contact type Tachometer has 5 Digits LCD Display. It is used to measure RPM of equipment that is hard to reach. It is Battery operated. It is used to measure in the range of 5 to 99,999 rpm complete in a box with all standard accessories.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
Digital Tachometer
DT5
-
High quality digital tachometer featuring multi-functions, wide measuring range and high accuracy.
-
Product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
EZ-Tach Digital Automotive Tachometer
325
-
The EZ-Tach makes RPM measurements quick and easy. This is a very useful tool for tune-up and other diagnostic work where accurate RPM readings are required. Just clamp over any spark plug wire and get accurate RPM on conventional or DIS ignition systems. The unit also features a data hold function. The large 2000 count LCD display shows; RPM, function, data hold indication and low battery indication. The EZ-Tach is powered by one 9 volt battery. Battery and instructions are included.
-
Product
Tachometers
HH100
-
The HH100 Hand-Held Digital Tachometer combines both contact and non-contact sensing to accurately measure RPM, surface speed, and length. When using the non-contact mode, rotational speed (RPM) is measured using a visible beam of light. The HH100 can be up to 14 inches away from the small piece of reflective tape that is affixed to the rotating element.
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
Receiver Tester
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
Digital Tachometer
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
This tachometer has wide range of applications, such as measuring rotating speed of machine, motors, wheels, lathe for metal or wood cutting work, etc.
-
Product
Qualification Tester
LQ404
-
Computer Gesteuerte Systeme GmbH
The qualification tester LQ402 is designed to support up to 12 DUTs (Device under Test), for which the loads are installed in separate load boxes. The system consists out of 3 cabinets. One is for the electronic components with the primary measurement devices and the other two hold the 12 load boxes.
-
Product
Torque Tester
CD-100M/10M
-
Ideal for daily inspection of electric screwdrivers. Use conventional joints. Five channels of pass/fail judgment conditions can be saved, and settings can be made simply by switching channels even if the tightening conditions change. 3 times more durable than the conventional model, even with sudden high torque. disassemble the joint due to excessive unwinding .
-
-
Product
ICT Tester
-
Adapter design, assembly and validation for Agilent, Keysight, HP, Checksum, Spea. Preparing and debugging ICT scripts. ISP Programming Integration. Integration of edge scan testing, Jest testing, digital testing, semi-functional testing, IC programming, FINN probes, and more
-
Product
Brightness Tester
-
A brightness tester can be used for measuring the brightness, whiteness and yellowness of paper, cellulose and other materials like porcelain and plastic. Many brightness tester devices can also measure different colors. The portable devices for professional use that PCE Instruments (PCE) has to offer are particularly suitable for quality control and compliance with ISO standards.
-
Product
Velcro Tester
TF151
-
TESTEX Testing Equipment Systems Ltd.
Velcro Tester, to determine the capability of Velcro used for shoes, garments, etc.Cut the specimen 540mm by 20 or 50mm in dimension from the sample being tested into the wheel of Velcro tester to be fitted completely. To subject Velcro (hook & loop) to repeated stripping and peeling for a certain number of times. Use tensile machine (another purchase) to measure its peeling strength (AS) and shear strength (PA) after this test.
