Sensors
detect a physical event then translate to a representative analog signal.
See Also: Measurement, Detectors, Meters, Transducers
-
product
PXI High Density Precision Resistor Module, 3-Channel, 3.5Ω to 395kΩ
40-298-142
The 40-298-142 is a high density programmable resistor module with 3 channels which can be set between 3.5Ω and 395kΩ with 0.5Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Citroen Oxygen Sensor
KS60113 - Citroen
Konstar Electric Industrial Co., Ltd
An oxygen sensor, also known as a lambda sensor, continually detects the oxygen content in the exhaust gases of an engine. The oxygen sensor output signal informs the vehicle's ECU (Electronic Control Unit) whether the AFR (Air-Fuel Ratio) is lean or rich. Based on this, the ECU adjusts the amount of fuel injected into the engine to achieve an optimal AFR.
-
product
Hall Effect Sensor Elements/ICs
ChenYang Technologies GmbH & Co. KG
is a sophisticated Hall Effect Gear Tooth IC featuring an on-chip 12-bit A/DConverter and logic that acts as a digital sample and hold circuit. A separate 6-bit D/A converterprovides a fixed hysteresis. The sensor does not have a chopper delay. It uses a single Hall platewhich is immune to rotary alignment problems.
-
product
Pressure Sensors
Whatever configuration you require, look to Sensata. Our devices span a spectrum of pressure ranges, configurations and form factors.High pressure (>750psi / 50bar)Micro Silicon Strain Gauge solutions provides rugged reliability and a hermetic seal for a wide variety of environmentsMid pressure (100 to 750psi / 6 to 50 bar)Ceramic capacitive or MEMS solutions offer a wide range of solutions tailored to application needs at superior valueLow pressure (inches of water to 100psi / 2mbar to 6 bar)MEMS solutions including TPMS offer extremely low power consumption and wireless connectivity
-
product
Weighing Sensors For Lifting Applications
Rugged wireless weighing sensors for accurate load monitoring in crane and lifting applications.
-
product
Soil Moisture Sensor
SoilWatch10
SoilWatch 10 is a soil moisture sensor which allows measuring relative water content in the soil. Our sensor does not have any exposed electrodes that usually corrode in resistive sensors. Whats more the reads will almost not drift over time or with temperature changes. Our sensor will give the same readings regardless of supply voltage. The sensor is weatherproof. It can be buried in soil for extended periods of time without adverse effects on accuracy or reliability. Designed to work with Arduino.
-
product
Signal Conversion Box for Linear Gauge Sensor
DG-0010/0020
This is a signal conversion box to convert 2-phase signals (TTL) from the linear gauge sensor GS/BS series into open - collector (DG-0010) or line driver (DG-0020) .This conversion box allows direct connection with the PLC *. It can also be transmitted over long distances.
-
product
PCI Precision Resistor Card 9-Channel, 2Ω To 52.4kΩ
50-297-033
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
I2C Soil Moisture Sensor
Capacitive soil moisture sensor interfaced via I2C. Additionaly provides ambient light and temperature readings. Open Source Hardware. Soil moisture sensing, Light sensing, Temperature sensing.
-
product
Position Sensors for Hazardous Environments
Intrinsically Safe systems provide a safe operating environment for personnel and equipment. Intrinsic Safety (IS) is based on the principle of restricting the electrical energy transmitted into a hazardous area, thereby ensuring that anysparks or heated surfaces that may occur as a result of electrical failures areinsufficient to cause ignition. The threat of an explosion is eliminated.
-
product
Cylindrical Photoelectric Sensor
CY-100 SERIES
Panasonic Industrial Devices Sales Company of America
CY-100 Series Sensors are available as Thru-Beam, Retroreflective (with and without polarization filters) and Diffuse Reflective Types. Standard (Axial) and Side-View (Radial) Types are available, providing flexibility when mounting the Sensors. Moreover, all Sensors can be ordered as a cable type or with an M12 plug-in Connector.
-
product
Temperature Sensors
TT420-LT
Features • 2-wire, loop-powered 4-20 mA analog output • Attachment probe, sensor, and 2-wire 4-20 mA signal conditioner • Integral 1/2" flexible liquid-tight conduit fittings • TT420Z-LT 1/4” stainless steel probe with 1/8 NPT adapter • TT420S-LT 3/8-16 threaded stud probe • FM approved, Dust Ignition-proof • Class II and III, Div I (E, F, G); NEMA 4
-
product
PXI High Density Precision Resistor Module, 3-Channel, 4Ω to 1.51MΩ
40-298-150
The 40-298-150 is a high density programmable resistor module with 3 channels which can be set between 4Ω and 1.51MΩ with 0.125Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
-
product
PCI High Density Pecision Resistor Card, 9-Channel, 2Ω To 31.5Ω
50-298-110
The 50-298-110 is a high density programmable resistor card with 9 channels which can be set between 2Ω and 31.5Ω with 0.125Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-122
The 40-297A-122 (PXI) and the 42-297A-122 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 1.81 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
acA1440-73gm , Monochrome GigE Vision, 1.6 MP, 73 FPS Area Scan Camera
787064-01
The acA1440-73gm is a Monochrome Basler Ace GigE Vision Camera with a 1.6 MP resolution and a maximum image acquisition speed of 73 frames per second. … The acA1440-73gm uses a IMX273 sensor and is quality tested and calibrated for high performance and reliability. This camera can be used with NI hardware and software to build machine vision systems.
-
product
Light-to-Analog Sensors (Voltage)
Renesas' light-to-voltage silicon optical sensors combine a photodiode array, a non-linear current amplifier and a micropower op amp on a single monolithic IC. Applications for these devices include display backlight control, keypad dimming, anti-glare mirror systems, and industrial and medical light sensing applications.
-
product
PIR Mini Sensor
28033
Do you have a big idea that needs a small motion sensor? The PIR Mini Sensor’s compact form factor is ideal for small-scale projects, and those where the electronics need to be hidden or protected. The narrow, vertically oriented board can slip through a hole in an enclosure to hide and protect the electronics, leaving only the small lens visible on the outside.
-
product
HD Visible and Thermal Pan/Tilt
Triton™ PT-Series HD
The FLIR Triton™ PT-Series HD is our most advanced dual-sensor security system, combining a cooled or uncooled 640 × 480 resolution thermal sensor, a 1080p HD visible-light imaging sensor, and a high speed, precision pan/tilt system. The Triton PT-Series HD integrates easily with FLIR United VMS 8.0, as well as other major third party video management systems, making it an extremely versatile solution for critical infrastructure protection in total darkness, bright sun, and adverse conditions.
-
product
Sensor Evaluation Kits
Panasonic Industrial Devices Sales Company of America
Accelerate prototyping and testing by utilizing Panasonic's Sensor Evaluation Kits for all your design needs. Discover today why Panasonic Sensors are the premier choice for creating unique IoT solutions.
-
product
PCI High Density Pecision Resistor Card, 6-Channel, 4Ω To 5.82MΩ
50-298-052
The 50-298-052 is a high density programmable resistor card with 6 channels which can be set between 4Ω and 5.82MΩ with 0.5Ω resolution The 50-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
Easy Sense Software
Easy Sense 2100 is available for use with the UPC2100. Easy Sense 225x is used with the Universal Data Acquisition System(UDAS) or the USB2251. The Software includes a GUI configuration utility that allows the user to set sensor type, gain range, channel, and all other input parameters. The configuration can be saved to non-volatile memory on the card so that the UP2100 or the UDAS can be used in embedded applications.
-
product
FBG-Scan 700/800
FBG-Scan 700/800
The FBG-Scan 700 and 800 are dynamic, high precision measurement devices for Fiber Bragg Grating (FBG) sensors. The system can measure up to 40 FBG sensors using 2 input channels. Both input channels are simultaneously monitored using an optical coupler at a scan rate up to 2000Hz.
-
product
SparkFun IR Thermometer Evaluation Board
MLX90614
This is an evaluation board for the MLX90614 IR Thermometer. The sensor is connected to an ATmega328 running at 3.3V with a STK500 (Arduino) 8MHz bootloader. Code can be loaded through the FTDI basic interface and the Arduino environment.
-
product
LGAutomation w/ RS763 Sensor
The LaserGauge® Automation system with RS763 Sensor automatically acquires fit and finish measurements of a vehicle in real-time on a moving line and can be integrated into the manufacturing line by plant personnel or independent robot integrators.
-
product
REM-11100, 2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O
784748-01
2-, 3-, 4-Wire, 4-Channel Voltage Input Module for Remote I/O - The REM‑11100 is a voltage input module for remote I/O. Remote I/O systems are low-cost, modular systems for simple machine control and measurements. A remote I/O system consists of an EtherCAT bus coupler and individual modules mounted on a DIN rail. You control the REM‑11100 from a real-time controller, such as a CompactRIO Controller or an Industrial Controller. You can use remote I/O hardware to add low-cost I/O for simple tasks while your controller handles advanced tasks such as image processing, motion control, and high-speed or specialty measurements. This module features 2‑, 3‑, and 4‑wire spring terminal connection methods, a built-in power supply for sensors, four selectable input ranges, and simultaneous sampling.
-
product
Force Sensors, Controls & Switches
Direct caliper motor/spindle integration for Brake by Wire systemsExtra-small form factor MSG sensors that weigh less than five gramsFacilitating system-level miniaturizationAdvanced button-type sensors designed to lower costs and improve accuracy
-
product
Sensors
NanoFocus Probe
Scan of 3D topography of high accurate featuresVery high point densitySuitable to perform non-contact roughness measurementsHigh flexibility using a range of different front lenses
-
product
LVDT to Digital and RVDT to Digital Converters
Computer Conversions Corporation
LVDT Displacement transducers accurately measure position and displacement. The strength of the LVDT is in its principle of operation. As LVDT sensors are inductive, there is no electrical connection across the sensor, which ensures clean, accurate data and a long life.
