Sensors
detect a physical event then translate to a representative analog signal.
See Also: Measurement, Detectors, Meters, Transducers
-
Product
Time Domain Sensors
TDS
-
Schmid & Partner Engineering AG
Time Domain Sensor (TDS) probes are miniaturized fully isolated active optical magnetic or electric field sensors operating in the frequency range from 10MHz to 6GHz. TDS offers unparalleled sensitivity for EM measurements resolved in the time and frequency domains while maintaining all amplitude and phase information.
-
Product
Distance Sensors
SR50A-L
-
The SR50A is a rugged acoustic sensor for measuring the distance from the sensor to a target. It is typically used to measure snow or water depth, but it is well-suited for other uses.
-
Product
CMOS Imaging Sensors
-
CMOS imaging sensors from ams feature global and rolling shutter capability, low noise, high dynamic range and high frame rates.
-
Product
General Purpose Vibration Sensors
AC102
-
Multi-Purpose Accelerometer, Top Exit Connector / Cable, 100 mV/g.
-
Product
Percent Oxygen Sensors
-
At Process Sensing Technologies (PST), we offer replacement electrochemical oxygen sensors compatible with major fixed and portable oxygen analyzers in challenging industrial environments. Tailor your solution with our versatile housing options, allowing you to specify either a 2-ring or connector design.
-
Product
Air Temperature and Relative Humidity Sensors
-
Air temperature and relative humidity probes typically consist of two separate sensors packaged in the same housing. Often relative humidity is measured with a capacitive RH sensor, while air temperature is measured by a PRT.
-
Product
Hyperspectral Imaging Sensors
-
HYPERSPEC® sensors are line-scanning instruments (sometimes called pushbroom) that collect reflected light through an image slit. One row of spatial pixels is collected per frame as motion occurs, with each pixel containing full spectral data. Motion can be accomplished in two ways: either as an airborne deployment (UAV, aircraft, or satellite) or stationary (where motion is accomplished beneath the sensor, such as a food inspection line). A third option is also available where pan-and-tilt or rotary stages allow a fixed-location sensor to scan a stationary object (such as a piece of artwork, or a mine face for geological applications).
-
Product
High Accuracy Fiber Optic Sensors
FS01
-
Compact & simple operation. New 12-bit concurrent CPU. 20-s response speed. Multiple calibration methods. Wire-Saving 0-line or 1-line connection
-
-
Product
Sunshine Duration Sensors
-
Easy to install, with no moving parts or complex on-site adjustment, the MS-95S reinvents sunshine duration sensors, setting new standards for accuracy and stability.
-
Product
Transparent Object Photoelectric Sensors
-
Contrinex Transparent Object Photoelectric Sensors
-
Product
MultiPoint Temperature Sensors
-
Ashcroft® offers a variety of multipoint temperature measuring instruments for processing facilities, power plants and chemical reactors throughout the world.
-
Product
Fluid Sensors For Aerospace
-
Pilots need to know how much fuel they have available. Maintenance engineers need to know the condition of the fluid. Design engineers need a system to provide accurate and reliable data. Our unique fluid sensors answer these questions.
-
Product
Sensor Unit for High Precision Current Sensors
CT9557
-
Hioki pull-through current sensors and clamp on current probes are best-in-class current sensing devices for use with power meters, Memory HiCorders and high performance oscilloscopes. The CT9555 is 4-channel sensor unit and power adapter for any of the CT686x series, 9709 and CT684x series current sensors and probes that provides waveform and RMS output.
-
Product
Position Sensors
-
Position sensor is a device that can detect the movement of an object and converts these into signals suitable for processing, transmission, or control. TE Connectivity (TE) is a leading manufacturer of industrial linear and angular position, tilt and fluid level sensors. Both off -the-shelf and custom position sensing solutions are available featuring our core technologies, including inductive, potentiometric, magnetoresistive, hall effect, reed switch, electrolytic and capacitive sensing.
-
Product
Cryogenic Temperature Sensors
Capacitance
-
CS capacitance sensors are ideally suited for use as cryogenic temperature control sensors in strong magnetic fields because they exhibit virtually no magnetic field dependence. Displacement current is not affected by magnetic fields. Consequently, temperature control fluctuations are kept to a minimum when sweeping magnetic field or when changing field values under constant temperature operation.
-
Product
Average Power Sensors
E9300
-
Operates with the EPM, EPM-P and P-series power meters Wide dynamic range sensors (80 dB maximum)Accurate average power measurements on all modulation formats Wide frequency coverage from 9 kHz to 18 GHz (special option to 24 GHz)Calibration factors stored in EEPROM Fast measurement speed over the GPIB (up to 400 readings per second with the E4416A)
-
Product
Temperature Measurement IR Sensors & Detectors
ST120 TO-5
-
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 1.2mm x 1.2mm in a TO-5 package. Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
Vehicle Test Sensors
-
Today's engines contain sensors to tell the vehicle's computer what's going on. Car sensors check for fuel-air mixture, incoming air temperature, wheel speed, and manifold pressure. They then tell your vehicle's computer what to do, based on that information.
-
Product
Refrigerant Gas Sensors
-
Dynament offers a range of refrigerant non-dispersive infrared gas sensors that measure R32 and R454b gases over the LEL range for use in refrigeration service and maintenance.
-
Product
Low Noise Coaxial Cables For Sensors
-
Low noise coaxial cables are used with single axis and triaxial charge mode sensors. This table provides relevant specifications for four cable types. Type 003 is the most commonly used, but three other types are also available.
-
Product
Measuring Fork Sensors
-
Leuze electronic GmbH + Co. KG
With the sensors, an infrared light-band illuminates a CCD line. A passing object can thereby be measured by its occlusion. The resolution of 14 µm and the high reproducibility enable the reliable measurement of very fine yarns and wires. The variety of implementable measurement functions enables the position detection of transparent edges, the determination of the thinnest or thickest wire and much more. The vacuum resistance of the devices also enables use in carbon fiber production.
-
Product
Ultrasonic Sensors
-
Leuze electronic GmbH + Co. KG
Ultrasonic sensors are used whenever optical systems reach their limits. Hence, partially and fully transparent or extremely dark objects can be detected just as easily as objects with reflecting surfaces or objects in dusty, vaporous or humid environments.
-
Product
Polarity Test Sensors
P-FINN
-
The P-FINN is a cost effective method of identifying object presence and/or orientation, and/or color. The key to the design is simplicity.
-
Product
Bearing And Surface Temperature Sensors
-
Can be used to monitor temperature on a wide range of industrial machinery including conveyors, bucket elevators, motors, gearboxes, pumps, turbines, fans, curing ovens, centrifuges, agitators and hammer mills.
-
Product
Large-Format/Wide-Area Surveillance Sensors
-
L3 Cincinnati Electronics is the industry leader in large-format MWIR with a decade of experience in providing IR technology for major programs such as the F/A-18 and F-35. In addition to our compact 1280 x 1024 and 2048 x 2048 pixel MWIR HD cameras, we are the only manufacturer with IR sensors of 16Mp (4096 x 4096 pixels) currently in use by U.S. assets in overseas combat zones.
-
Product
Hall Effect Speed Sensors
-
SPECTEC Innovative Sensor Solutions
SPECTEC zero speed Hall effect gear tooth sensors are used in industrial applications to determine shaft or gear speed or direction by detecting fluctuations in the magnetic field. The Hall effect technology fulfills a wide array of applications due to a Hall effect sensor's ability to detect zero speed and the quadrature sensor's ability to detect direction change. The Hall effect gear tooth sensor's digital output is easily read by computers, motion control devices, position monitors and digital to analog converters. Intrinsically Safe zero speed sensors are available for various applications.
-
-
-
Product
Capillary-fill sensors
-
Zimmer and Peacock have launched the world's first capillary fill sensor for the Research and Development market, both academia and industry. We provide these capillary-fill sensors in gold, platinum and carbon.
