Compression
the result of being pressed.
See Also: Force, Crimp Force, Pull Force, Pull off Force, Push Pull Force, Peeling, Tension, Gravity, Electrical, Magnetic, Crush, Extensometers, Bending
-
Product
Compressed Air RH+T+Tdp Sensor
T3111P-4
-
Relative humidity, temperature sensors at probe on the cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
AC Magnetostriction Measurement Equipment
TLVM
-
This equipment measures quantitatively magnetostriction to indicate mechanical striction in magnetizing direction caused when magnetic steel sheet sample was alternately magnetized and is used for research and development of magnetic steel sheet. Magnetostriction is detected as speed signal through the parameters of magnetic flux density and compressive stress with laser doppler vibration meter.
-
Product
Heavy Duty Diesel Compression Tester
DCT1570
-
Compression tester and adapters to test many vehicles, trucks, heavy-duty equipment. Covers Cummins, VW, Volvo, Allis-Chalmers, Bedford, I.I.Case, John Deer, IH, Mack, Massey-Ferguson, Mitsu-Fuso, Scania, White Farm, Detroit Diesel, and more.
-
Product
Compact Ultrasonic Testing Device
SONAPHONE® Pocket
-
With the SONAPHONE Pocket you identify problems even before they arise and create value at all levels of your company. Just by detecting and eliminating leaks you can reduce the energy costs for your compressed air system up to 30 percent. This also has positive effects on your operational safety and system productivity through early warning of bearing failure and evidence of partial electrical discharges.
-
Product
COMMON RAIL Electronic Diesel Injection Analyzer
EDIA-PRO
-
The EDIA-PRO is an enhanced version of the proven EDIA-5 analyzer. To meet expectations of our customers we created a system for automatic evaluation of injection system parameters based on measured waveforms. This makes the diagnosis easier and faster. Additional possibility of fast evaluation of cylinder compression and ability to check starting performance along with control valve measurement mode are perfect complement to diagnostic capabilities of EDIA device.
-
Product
Capture & Replay System
-
PacketStorm Communications, Inc.
The PacketStorm CRS is a packet capture and replay system with hardware time stamping at 10Gbps. The user specifies which packets to capture based on the filter parameters. Packet captures can be continuous or stop capture after a certain number of frames, bytes, or time. The 10G filters include: Source Address, Destination Address, Source Port, Destination Port, and Protocol. The CRS file management includes automatic file compression and decompression. Operation is via the console or the remote GUI. There are two CRS versions: 1U and Lunchbox. The 1U version is intended to be installed in a rack or on a test bench. The lunchbox version includes a keyboard, mouse, and monitor and is intended to be moved about between stations and labs.
-
Product
Axial Extensometer
Model 3542
-
Jinan Testing Equipment IE Corporation
These extensometers are designed for testing a wide range of materials, including metals, plastics, composites and ceramics. All will work in both tension and compression. The dual flexure design makes them very rugged and insensitive to vibrations, which permits higher frequency operation.They come standard with Epsilon’s quick attach kit, making it possible to mount the extensometer on the test specimen quickly and easily with one hand. The quick attach kit can be removed, allowing mounting of the extensometer with springs or rubber bands.The Model 3542 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.For gauge lengths 100 mm (4 inches) or greater see Model 3542L.
-
Product
Large Telemetry Compressive Load Cell
TC-3.0-LG
-
DLM’s Telemetry Compressive Load Cells can be used independently or in combination as part of weighing platforms.They range from 100t to 300t and manufactured using high grade stainless steel, making these load cells particularly suited to rugged environments and the hire industry. Bespoke size compressive load cells can be designed upon request. Some applications include: tank weighing, hydraulic lifting operations, vessel weighing and certification.
-
Product
Flow Sensor For Compressed Air (separate Display Type FLUEREX)
PFD
-
Separate display type flow sensor for compressed air. Ideal for large flow rate measurement.
-
Product
Ergonomic Force Gauges
-
The ergonomic gauges from Chatillon are ideal for functional capacity evaluations and basic muscle strength measurements where economy and ease-of-use are essential. Simplicity is a key design criterion for these ergonomic gauges. They are an excellent, low cost solution for tensile or compression testing.
-
Product
proctorers
-
For automatic compression of simple and modified Proctor specimens 100 and 150 mm. Stand model for installation on a stable surface with CE safety door in accordance with the EU Machinery Directive. The Proctor mold used for the respective test is placed on the rotatable base plate and the corresponding monkey hammer inserted into the lifting device. Exchangeable drive disks and cams control the drop height and the rotary feed rate after each stroke. The displacement of the impact surface sample edge / center / sample edge is done by an electric drive. The entire compaction process is microprocessor-controlled with universal software and preselectable test parameters:
-
Product
Signature Compression Only Load Button Load Cells
SLB SERIES
-
The SLB Series Subminiature load cells (Load Buttons) are offered for compression only applications where space is limited. The matching surface must be flat for ultimate accuracy. The loading diameter is slightly convex for accurate load distribution. These sensors are manufactured from heat treated 17-4ph stainless steel, and the sensing element incorporates bonded foil strain gages of the highest quality. They are sealed for protection against most industrial environments.
-
-
Product
High Temperature Hot Mountable Furnace Extensometers (1200 Cor 1600 C)
Model 3549
-
Jinan Testing Equipment IE Corporation
The Model 3549 is a major advancement in the design of externally mounted, furnace extensometers. This new extensometer is designed to meet the stringent requirements of strain controlled testing as prescribed in ISO 6892, while introducing many new innovative features that help improve productivity with static testing applications (tension and compression testing) and long term testing such as low cycle fatigue and creep. The overall design reduces any influence from common lab environment vibrations. This unit also incorporates a new feature that allows the user to precisely set the contact force against the test specimen. This allows for even and repeatable contact force, limiting contact force induced errors. This extensometer mounts on a slide bracket (included) that can attach to the load frame of your test system; optional load frame mounting brackets are available. The gauge length for the 3549 is automatically set prior to mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.
-
Product
Femtosecond Terawatt Ti:sapphire Laser System
MPA-XL
-
MPA-XL is a cost-effective terawatt Ti: sapphire amplifier system. It gives up to 200 mJ energy of the stretched pulse and further compression with 65% efficiency. A standard air compressor can be placed into a custom designed vacuum chamber.
-
Product
Static Load Cells (500 N to 600 kN)
2580 Series
-
The Instron 2580 Series static load cells are high-precision force transducers optimized for use with 5900 and 6800 Series universal testing systems, capable of measuring loads across a wide range (up to ±600 kN) with accuracy to 0.5 % of reading and sensitivity down to 1/1000th of full scale. Temperature-compensated and calibrated on equipment traceable to international standards, they have automatic recognition with an electronic serial number and support electronic calibration, while offering overload protection (up to 150 % without damage, 300 % without mechanical failure). The 2580’s design delivers high stiffness and reliable alignment under load—making it a robust choice for tension, compression, cyclic, and reverse stress testing in materials and components.
-
Product
Rubber Testing Equipment
-
Dongguan Amade Instruments Technology Co., Ltd
Rubber testing equipment are used to test the physical properties, chemical properties, thermal properties of uncompounded and compounded rubbers at prescribed conditions to help manufactures or researchers in comprehending the characteristics, updating the formula and improving product quality. Including volatile component, ash content, Mooney viscosity, vulcanization curve, Mooney scorch time, hardness, tensile properties, tearing, the compression performance, impact, friction resistance, fatigue resistance, peel strength, vertical & horizontal combustion, smoke density, limiting oxygen index, the flame spread rate, the surface resistance, surface resistivity, volume resistivity, the breakdown voltage, dielectric strength, dielectric loss, antistatic properties, Aging test (UV, Xenon lamp, carbon arc lamp, ozone) etc.
-
Product
6 Channel Digital Receiver Module
DP-VME-5826
-
DP-VME-5826 is a VME64x Six Channel Digital IF Receiver module. It samples and down converts analog IF signals into the digital base band data.The digital base band I/O samples generated from these IF samples are pulse compressed. Down converted I/Q data is sent to the signal processor through 2 channels of 2.5 Gbps speed SFPDP link.The digital waveform generator block of digital receiver unit generates programmable polyphase coded digital pulse coded expander output.
-
Product
Modulated Wideband Driver Amplifier
TBMDA2
-
The TBMDA2 modulated wideband driver amplifier is designed in order to create an inexpensive signal source for immunity testing of electronic building blocks and products. It is designed to be driven by the tracking generator output of spectrum analyzers. With its 1dB compression point of +27dBm, it can boost the output power of a tracking generator up to 500mW.
-
Product
CATV Fiber Optic 1550nm Transmitter
T8500HC Series
-
The MX-T8500HC series externally modulated transmitter delivers high performance signal transmission of NTSC, PAL, digital or compressed digital signals from 50-862 MHz for CATV applications.
-
Product
6-Axis Robotic Automated Testing System
AT6
-
The Instron AT6 is a flexible, robot-assisted testing solution featuring six axes of motion, purpose-built to automate tensile, compression, flexural, and lap shear testing in alignment with widely used ASTM and ISO standards. Its modular design accommodates a broad array of materials—including metals, polymers, elastomers, films, composites, and sutures—at force capacities up to 600 kN. Capable of processing up to 500 specimens without operator intervention, the AT6 enables true unattended or “lights-out” operation, significantly increasing throughput around the clock. Optional modules include stations for specimen measurement, automated strain measurement, environmental temperature chambers, and multiple test frames for simultaneous testing. The system also integrates smoothly with auxiliary devices such as durometers, hardness testers, and surface roughness testers, making it a robust solution for high-volume, high-efficiency testing environments.
-
Product
BenchMate Active Air Vibration Control
2212 Series
-
BenchMate Vibration-Free Platforms enhance the performance of precision tabletop equipment.The 2212 Series is an Active-Air design that requires a source of compressed air (not included). It is a self-leveling unit and recommended for regular use.
-
Product
Compression Deflectometers
LVDT
-
These general purpose deflection measurement devices are based on LVDT transducers. A variety of travels is available to suit a wide range of applications.
-
Product
Canister Load Cells
-
PCB's cost-effective canister load cells are easy to install and ideal for low-capacity applications. Canister style load cells include a built-in mounting base for a simplified installation in both tension and compression applications.
-
-
Product
LVDT With Pneumatic Function
-
INELTA Sensorsysteme GmbH & Co. KG
2-3 bar compressed air moves the strings out the integrated return spring pulls the output back into the housing
-
Product
Mechanical Force Gauges
-
AMETEK Sensors, Test & Calibration
The mechanical force gauges from Chatillon offer high precision compression testing (Push) and tensile testing (Pull) at a low cost on a wide range of testing applications.
-
Product
Analogue Concrete Test Hammer
181
-
The Elcometer 181 Analogue Concrete Test Hammer provides a quick, simple and inexpensive method for non-destructive evaluation of concrete compression strength and other masonry materials.
-
Product
Wide Range Individual Bay Chambers
KDZ
-
The Bemco KDZ is similar to the Bemco Kardburn KDR except it has a wider temperature range, a built-in product support system, a latched glass door with a compression gasket, and every bay has it own independent conditioning system, refrigeration package, heaters, and controls.
-
Product
Dew Point Monitor
DPM-99
-
The NFPA99 has mandated that for Med Gas systems the "dew point for locally compressed air shall be monitored and alarmed per 4-3.1.9.8 and 4-3.1.1.2(f) to protect from line pressure dew point rise to 39 degrees F (3.9 degrees C) from a nominal design of 35 degrees F (1.7 degrees C)." This safeguard was the foundation for the new Edgetech Instruments DPM-99 Med Gas Dew Point Monitor. This specifically designed monitor exceeds the requirements set forth by the NFPA and was a collaboration with AIRVAC Technical Services who are certified by P.IP.E as medical gas inspectors in all 50 US States.
