Inertial Measurement Units
combinations of precision gyroscopes, accelerometers, magnetometers, and pressure sensors measuring motion.
See Also: IMU
-
Product
X-ray Fluorescence Measuring Instrument
FISCHERSCOPE® X-RAY XDLM®
-
Universal instrument for inspection of small parts and small structures, measuring of light metals, hard coatings and thin electroplated parts.
-
Product
3U cPCI Sensor Interface Unit
SIU33
-
NAI's SIU33 is a highly configurable rugged COTS system or subsystem ideally suited for rugged military, industrial, and commercial applications that require high-density I/O, communications, Ethernet switching, and processing. The SIU33 uses up three NAI field-proven, 3U cPCI boards to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-to-Mission."
-
Product
Instrument Systems LED Measurement Accessories
-
Konica Minolta Sensing Americas, Inc
It’s critical to use the appropriate LED measurement equipment and accessories when evaluating an LED’s various photometric and radiometric quantities. Because all of the test adapters Instrument Systems designs are compliant with CIE 127:2007, users are assured of compatibility between measurements. Instrument Systems has a diverse array of LED Measurement Equipment.
-
Product
RFID Evaluation Units
-
- Wide range of interfaces for RFID evaluation units- Robust antennas and ID tags with long writing / reading distance
-
Product
Measuring Stations
-
The main application is the measurement of the flux density on the surface of multipole magnets or components with magnets. A large amount of measuring stations is built for rotors.
-
Product
Temperature Measurement IR Sensors & Detectors
ST120 TO-5
-
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 1.2mm x 1.2mm in a TO-5 package. Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
Emergency Power Supply Unit (EPSU) (8) 5-15R 1U/0U V/H
EPS-815-HV
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
Measuring Devices for Magnetically Soft Materials
MAG-TD200
-
The computerized measuring system is designed for measure the dynamic magnetic properties of the soft magnetic materials e.g. oriented or not-oriented electrical sheet under alternating or rotational field. The system provides the opportunity of a tabular and graphic presentation of the obtained data, which can be presented by means of monitor, printer or plotter. The computerized measuring system MAG-RJJ-6.0 is also adapted to measure the dynamic magnetic properties of the soft magnetic materials as a function of temperature.
-
Product
Radiated Power Measurement
-
One of the most important properties of a wireless device is how much it actually radiates, how efficient is the antenna.This is typically measured in an anechoic chamber (at an expensive test lab). Another, time-consuming and inaccurate, method is by walking around in a free field and test the communication distance.
-
Product
Multiport Calibrated Measurements With Switch Instruments
S95553B
-
This application provides a macro which enables full multiport error correction and measurement capabilities using external switch instruments such as the M9164A/B or M9165A/B PXI Solid-state Switch Matrix. The software includes an easy-to-use measurement wizard that simplifies measurement procedures and reduces the setup time of complicated multiport measurements. The VNA displays measured multiport S-parameters.With the combination of M980xA PXIe VNAs and M916xA/B switch matrix, up to 66 ports (2 VNAs (4 ports and 6 ports M980xA), plus 4 modules of 2x16 M9164A/B) can be configured and supported. Measurement specification is supported when using the M9164B/M9165B 9 GHz switch modules.
-
Product
Interface And Signal Processing Units
-
The interface and signal processing units extend the field of application of Micro-Epsilon sensors. The interface modules are used to convert sensor signals into digital or bus-compatible interfaces. This enables interfaces such as USB, RS422, Ethernet/IP, Profinet and EtherCAT for numerous sensors. The signal processing units are also used to record several sensor signals, to calculate and output them together. This is necessary, for example, for planarity measurement or thickness measurement.
-
Product
Potential Measuring Coils
-
measure the magnetic potential of magnets, magnet systems and their surroundings.
-
Product
Multiport Calibrated Measurements With Switch Instruments
S97553B
-
This application provides a macro which enables full multiport error correction and measurement capabilities using external switch instruments
-
Product
Remote Terminal Unit (RTU) Replacement
-
Schweitzer Engineering Laboratories, Inc.
Compared with typical RTUs, SEL automation controllers provide improved reliability, extended I/O contacts, and advanced automation and control for remote substations and field applications.
-
Product
Gain-Compression Measurements
S93086B
-
The S93086B gain compression application (GCA) adds the software capabilities to the PNA Series B model network analyzers to evaluate the characteristics of compression point of an amplifier or frequency converter.
-
Product
Current-Voltage Measurement System
-
Sciencetech''s IV Testers are electrical current-voltage measurement systems used to characterize photovoltaic cell performance. This current-voltage tester works by sampling various current versus voltage combinations of the photovoltaic cell with a variable impedence load.This IV Test system can measure electrical power from photovoltaic cells up to 20W. The voltage envelope is limited to 20V and the current to 1A. A higher power version, up to 60W, is available. In general, the limitation on this model is the 1A current limit: if your solar cell generates more than 1A, we recommend upgrading to the 60W version.
-
Product
Combined Map Display Unit & Interface Unit Tester (COMED)
MS 1117
-
This system is used to test COMED (Combined Map Electronic Display) IFU cards. This ATE checks the LRU Status and card status and identify faulty component in the individual UUT. On fault, this suggests the possible component failure as diagnostic report, for repairing the cards.
-
Product
Impulse Current Measuring Shunts
ICMS
-
The Impulse Current Measuring Shunts ICMS are new designed tubular shunt types with best response behavior to match the high performance of the TR-AS digital recorder for comparative current measurements. A 1st partial response time less than 10ns and a settling times less than 20ns show the advantage of these shunts. They show no initial overshoot peak, no oscillations and do not need compensation box to optimize the transient behavior as known from e.g. cage shunts.
-
Product
Contour And Surface Measuring Machines
-
The contour and surface measuring machines from ZEISS offer different, sometimes combinable sensors for roughness measurements, contour measurements or both. The contact-free linear drive makes these machines highly efficient and low-maintenance.
-
Product
Magnetic Field Measurement Systems
-
The magnetic field probe performs non-contact current measurements and can be used for real traces. The probe of higher resolution enables pinpoint measurements.
-
Product
Unit Testing Mocking Solution for .NET
Suggest
-
Suggest creates automatic test suggestions suitable for your code.
-
Product
Radius Measurement
Spherometers
-
Ultra-accurate measurement of radius of curvature. Our spherometers have become an industry standard for ultra-accurate radius measurement and calibration of test glasses. The long term accuracy and automated features make our spherometers the preferred instruments for laboratory and production environments.
-
Product
Harmonics And Flicker Measuring System
ProfLine Series
-
The Teseq ProfLine system is a complete and cost effective Harmonics and Flicker measurement test system which compiles to the latest IEC/EN standards, including IEC 61000-3-2 and IEC 61000-3-3. The programmable power generation capability of up to 45 kVA (90 kVA and 145 kVA sources comprise multiple 45 kVA units) provides more than ample power to cater for a wide range of Equipment Under Test (EUT).
-
Product
Photoluminescence & Electroluminescence Measurement System (PL/EL)
PL
-
PL/EL Measurement System includes Laser, Spectrometer, Lock-in amplifier, Optical Chopper, Sample Holder(PL/EL), PMT/CCD, Fiber, Optical optics, Optical Table, Refrigerator（low temperature）,Sample Chamber and related accessories;
-
Product
IV Characteristics Measurement Device [
PECK2400-N
-
Easy-to-use measurement software supports IV measurement (software + source meter + connection cable). Compatible with Windows 10. RS-232C connection (PC is optional). Works with NI GPIB. Simultaneous use with IPCE PEC-S20 D type is possible. There is only one operation panel. done on one screen.
-
Product
VLF Testing and Diagnostics Unit
Frida TD
-
Cable testing and diagnostics with the BAUR frida TD. The portable and high performance high-voltage testing and diagnostics device is available in two different configurations: frida: Used for cable and cable sheath testing of medium-voltage cables and electrical equipment up to 20 kV. Another function is insulation testing on electrical equipment.frida TD: Expands the functional scope of frida with the tan delta diagnostics and Monitored Withstand Test (MWT) that combines the cable testing and dissipation factor measurement. This allows for an accurate and comprehensive assessment of the cable condition.* Cable testing and dissipation factor diagnostics in one device* Easy and quick test setup* Automatic testing and diagnostic sequences* Compact dimensions and lightweight
-
Product
Measurement
Ambient Noise
-
The Ambient Noise (AN) measurement is done in accordance with CISPR 22 and EN 50022
-
Product
50 Channel Linear Vibration Motor Aging Unit
BK2021
-
The BK2021 50 Channel Linear Vibration Motor Aging Test System was designed to test your linear vibration motors so you know they are working. Load a jig drawer in the jig assembly unit with 10 DUT's. Close the drawer to start testing and begin loading the next of the 5 drawers. When the machine has finished running up to 4 test sequences that you've programmed in, the drawer opens. On the front, a green light tells you the motor is good, a red light tells you there was a short and if there is no light you know there was an open circuit.
-
Product
Current Measurement in a Compact Design
ICD-Series
-
Isabellenhütte Heusler GmbH & Co. KG
The ICD series is a compact system for current measurement. The ICD-A is suitable for an application in the automotive industry due to its connector, while the ICD-C is more suitable for the design industry. The shunt-based measurement provides for a high level of accuracy and temperature compensation is also incorporated through the internal signal processing. External temperature influences are thus reduced to a minimum.
-
Product
IV Characteristics Measurement Device Software
Keithley 2400, 2401 and Keithley 2450
-
*Windows 10, Windows 11 (Compatible) RS-232C (Keithley 2400, 2401), USB (Keithley 2450)*NI GPIB can also be used (optional)*IPCE PEC-S02 can be used simultaneously. operation panel. *Everything from condition setting to measurement can be done on one screen.
