Filter Results By:
Products
Applications
Manufacturers
- Pickering Interfaces Inc.
product
Single Bus 75-Channel 2A PCI Fault Insertion Switch
50-190-001
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
Automotive Serial Triggering and Analysis (CAN, LIN) for DSOX1000 Series Oscilloscopes
DSOX1AUTO
The automotive serial triggering and analysis (CAN, LIN) option for InfiniiVision 1000 X-Series oscilloscopes allows you to trigger on either standard or extended CAN message IDs, including the message ID of a remote transfer request frame. It supports triggering on a data frame and allows you to specify message IDs, data and data length for filtering messages of interest. Triggering on active error frames also is supported. In addition, it supports triggering on LIN frame IDs and data, and it includes color-coded parity and check sums errors. You can easily isolate serial packets to find error sources due to hardware or software related problems.
-
product
CAN + OBD Network Data Converter
NC2
Add Vehicle Network based Data Acquisition to your existing fleet data acquisition systems for under one thousand dollars with the NC2. Great for NVH Tachometer applications.
-
product
The PC Link Software For CAN/LIN Data
LE-PC87
This PC link software “LE-PC87” captures CAN/LIN data into PC measured by the CAN/ LIN optional expansion kit for LE-8200A/LE-8200.
-
product
CAN + OBD Network Data Converter
NC1
Get RPM, Speed, Absolute throttle position and many other vehicle parameters in real-time from your vehicle's standard OBD connector. Works with ANY OBD2 equipped vehicle. Works with ANY data acquisition equipment.
-
product
64-Ch 1-Bus Fault Insertion
YAV91082
64 channels 1 thread 2A 250V 1 Fault Insertion Buses Switching up 60W CAN Control (or Ethernet with Ethernet to CAN Gateway) Drivers dll & VIs available
-
product
National Instruments System Integrator
Knowledge of all National Instruments platforms and its wide experience in using and integrating NI hardware (CompactRIO, sbRIO, PXI, CAN, DAQ, etc.) and software (LabWindows/CVI, LabView e TestStand), IPSES offers to its clients customized solutions and services, providing both technological and economic benefits.
-
product
PCI-8513, 2-Port, Software‑Selectable/FD CAN Interface Device
780684-02
2-Port, Software‑Selectable/FD CAN Interface Device—The PCI‑8513 is a controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. NI‑XNET software-selectable CAN interfaces offer the best flexibility for CAN development with onboard transceivers for high-speed/FD, low-speed/fault-tolerant, and single-wire CAN as well as any external transceiver. The PCI‑8513 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, automation control, and more. The NI‑XNET device‑driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts.
-
product
OBD II Data Link Connector Breakout Box & Diagnostics Software
Mr. BOB DLC
Automotive Diagnostics and Publishing
Mr. BOB DLC OBD II Data Link Connector Breakout Box & Diagnostics Software for Network Waveform Viewing. This OBD2 breakout box with 8 Graphing Meter Scope like channels, is designed for the OBD2 DLC data link connector. Includes OBD II protocols such as PWM, ISO, KWP2000, 9151, J1850, VPW and CAN.
-
product
PXIe-8510, 6-Port PXI Vehicle Multiprotocol Interface Module
784122-01
2- or 6-Port PXI Vehicle Multiprotocol Interface Module—The PXIe‑8510 is a hardware-selectable controller area network (CAN) and/or local interconnect network (LIN) interface for developing applications with the NI‑XNET driver. The PXIe-8510 excels in applications requiring real-time, high-speed manipulation of hundreds of CAN frames and signals, such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
product
Mini Logger
J1939
The DAWN J1939 Mini Logger™ is a compact logger that acquires CAN bus data from heavy-duty trucks, buses, and off-road vehicles. It fits directly on the J1939 connector. The J1939 Mini Logger is part of the Mini Logger family of compact, low-cost, data loggers that acquire a variety of data from trucks and cars.
-
product
cDAQ-9134, 1.33 GHz Dual-Core Atom, 4-Slot, Extended Temperature CompactDAQ Controller
783340-01
1.33 GHz Dual-Core Atom, 4-Slot, Extended Temperature CompactDAQ Controller - The cDAQ‑9134 controls the timing, synchronization, and data transfer between C Series I/O modules and an integrated computer. It includes Intel Atom dual-core processing and 32 GB nonvolatile storage for data-logging and embedded monitoring in extreme environments. You can choose between running Windows or NI Linux® Real‑Time. The cDAQ‑9134 offers a wide array of standard connectivity and expansion options, including SD storage, USB, Ethernet, RS232 serial, and trigger input, and an integrated NI‑XNET port. You can combine the cDAQ‑9134 with up to four C Series I/O modules for a custom analog I/O, digital I/O, counter/timer, and controller area network (CAN) measurement and logging system. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
Pressure Transducers with CAN Bus Interface
P66
The Validyne model P66 is a digital differential pressure transmitter designed for industrial pressure measurement applications. The on-board microprocessor provides high accuracy and improved stability in changing thermal environments. Communication via CAN Bus provides remote zero and span adjustment as well as digital pressure readings in engineering units or pressure counts.
-
product
Multi Protocol Boards
The EXC-4000 carrier board series was developed to meet the needs of avionic testers for multi-protocol integrated, digital bus testing. Modules may be selected out of a growing list which currently includes MIL-STD-1553/1760, MMSI, H009, ARINC-429, ARINC-708/453, Serial (232/422/485), Discrete and CAN bus. Additionally, an IRIG B decoder implements a global time stamp relative to the IRIG B pulses. The need for higher density, different protocols, and multi-channel on one integrated test card has made the EXC-4000 series very successful.
-
product
6x (1 to 4) 50 Ohm 2.5 GHz MCX Multiplexer
YAVAL034
6x (1 to 4) MMCX connectors CAN Control (or Ethernet with Ethernet to CAN Gateway) Reflective
-
product
NI CAN Cable, No Term, High-Speed/FD/Low-Speed, D-Sub 9-Pin F, 1m
193128-01
9-Pin Female D-SUB to 9-Pin Female D-SUB CAN Cable - The DB9F-DB9F CAN Cable connects C Series CAN Interface Modules, C Series LIN Interface Modules, or C Series Multiprotocol Interface Modules to devices, breakout boxes, and accessories. It is sometimes referred to as CAN Cable (single termination or no termination). This cable is compatible with high-speed, flexible data-rate, and low-speed/fault tolerant CAN signals, available with or without termination, and in different lengths.
-
product
PowerTrain Simulators
NMEA 2000
The Au NMEA 2000 PowerTrain simulators V1.00A release can generate majority of NMEA 2000 PowerTrain Controller Area Network (CAN) signals on a NMEA 2000 network. Au NMEA 2000 PowerTrain simulators are designed very easy to use. All editions run independently (without personal computer). It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
product
CAN FD/CXPI Communications Expansion Kit
OP-SB87FD
OP-SB87FD is an expansion board for LE-8200A/LE-8200 used for monitor/simulation of CAN (ISO 11898-1), CAN FD (ISO11898-1:2015), and CXPI (JASO D015). With this kit and the line state sheet, LE-8200A/LE-8200 works as a stand-alone type analzyer for CAN, CAN FD, and CXPI. The board supports development of CAN (used for automotive industry and other industries), CAN FD (next-generation standard of CAN providing more high-speed and communication capacity), and CXPI (invented in Japan to replace direct wirings) devices.
-
product
Multiplexed Measurement Unit
YAV90MMU
YAV90MMU module (Multiplexed Measurement Unit) is a powerful subsystem containing 16-channel multiplexer and a 600V data acquisition channel with capability to control external switching and it is expandable through CAN bus.
-
product
Three Phase AC Voltage Source
EAC-TAVS
Electronic Test & Power Systems
The EAC-TAVS is a series of programmable high power AC voltage sources. Each system provides a three phase true sinewave output as standard. Each unit is built in a freestanding cabinet. The output frequency is adjustable in the range of 45 - 105Hz. Different frequency ranges are optional, with up to 805Hz possible. An RS-232 and CAN interface are provided as standard. The high resolution TFT front panel displays a host of measurement and setting functions. Besides standard models, other nominal power levels and voltages can be user specified. Single phase and bidirectional versions are available on request.
-
product
RL78 Family Of 8/16-bit Ultra-Low Energy MCUs
RL78/F1x
The RL78/F1x microcontrollers are suitable for automotive applications. As the successors of both the 78K0R and R8C, they realize low power consumption and are equipped with built-in functions suitable for automotive applications such as CAN communications, advanced timer, and safety functions.
-
product
ARINC825 (CAN Bus) Test & Simulation Module for VME With 4, 6 Or 8 CAN Bus Nodes
AVC825-x
ARINC825 (CAN bus) Test & Simulation Module for VME with 4, 6 or 8 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The AVC825-x VME card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
product
Temperature Sensors
The infrared sensor measures temperature at a distance without contacting the target. The integrated infrared module senses the thermal radiation emitted by objects on a 16 x 4 array of sensing points, for measuring the temperature distribution across a surface. These 64 measurement pixels are transmitted via CAN to the host controller or data logging device. The sensor is available in both 35 and 60 field of view options to suit a variety of installations. A software package is provided for viewing live temperature data from the array.
-
product
48-Ch 2A-250VAC 2-Bus Fault Insertion
YAV90076
48 channels2A 250V 2 Fault Insertion BusesSwitching up to 60CAN Control (or Ethernet with Ethernet to CAN Gateway)Drivers dll & VIs available
-
product
Network Analyser And Diagnostics
Module Analyser
Module Analyser is a 5 in 1 easy to use CAN bus analyser with the following advantages:■ CAN and LIN monitoring via DBC/LDF/Fibex files ■ Automotive OBD ISO15765 Scan tool and UDS ISO14229■ J1939■ Integrated ODX/MDX editor■ Data acquisition and logging
-
product
Data Acquisition System - 3U 5-Slot
DAQ-35CP0G
is a preconfigured rugged system ideally suited to support a multitude of military/aerospace data acquisition applications that require "SBC-less" remote Gig-E command and control of high-density, multichannel programmable ARINC 429/575; Dual-Redundant, Quad Channel MIL-STD-1553B; CANBus (CAN 2.0 A&B or J1939); A/D Conversion; RTD Measurement; RS-232/422/485 Serial Communications; Thermocouple Measurement; Discrete I/O; Differential Transceiver and Dual-Port Gig-E Ethernet.
-
product
Temperature Measurement
K- TC16
The K-TC modules belong to the Influx K-series instrumentation range for CAN applications. The stackable K-TC is an ideal for those applications that require a large number of thermocouples for example vehicle durability, winter and summer testing.
-
-
product
Industrial CANopen And CANopen FD Module For Digital I/O Applications
PCAN-MicroMod FD DR CANopen Digital 1
The PCAN-MicroMod FD DR CANopen Digital 1 is an I/O module for use in CANopen and CANopen FD networks. The modern CANopen FD® standard makes it possible to cope with the constantly increasing need for data transmission from sensors, machines and complex production systems. The module has a CAN FD interface as well as 8 digital inputs and 8 digital outputs. With the DIN rail housing and the support of the extended temperature range, the module is suitable for use in an industrial environment.
-
product
Full-Size PCI Express Mini Module With CAN Bus
AX92903
*USB to 1 channel CANBus port*Support CANOpen*51 x 30 mm
