Filter Results By:
Products
Applications
Manufacturers
Coil
One or more spiral turns of a conductor.
See Also: Helmholtz Coils, Coil Turns, Rogowski, Impulse Winding Testers, Transformer, Inductor
- Taylor Dynamometer, Inc.
product
Towing Dynamometer
RS-60K
RS-60K towing dynamometer is designed for testing Class B trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-60K is built with a heavy duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-60K is designed to maintain 60,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds.
-
product
Relay / Magnetic Field Testers
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for checking magnetic fields and the correct function of coils, e.g. Relays and solenoid valves. The magnetic field detector works without contact, so that opening the housing is not necessary in most cases. When a magnetic field is detected, the probe tip lights up permanently blue, with clocked relays in the same cycle as they are controlled. The function of the magnetic field detector can be checked before each measurement with the enclosed test permanent magnet.
-
product
DC Resistance Tester
DCSS502BC
Resistance meter is designed to measure copper resistance of transformers, wires, cables, other conductors and other coil products etc. It is widely used of low resistance measurement of switches, heater wires, transformers, relays, motors, electric films and PC circuit boards, wires, cables, etc. With reliable Good/ NG judgement, it is a premier resistance meter for the use in production line or QC department.
-
product
Solenoid Valve Tester
DZ800
Shanghai Aoboor Electric Co., Ltd.
Insulation resistance, HIPOT, coil DC resistance, turn to turn surge tests can be automatically completed in one time. Applicable to electrical performance test of solenoid valves, changeover valves
-
product
Multifunction Voltage and Current Calibrator
MC140i
Multifunction calibrator MC140i is ideal for calibration of voltmeters, ammeters, DMMs and panel meters. AC/DC voltage 1uV to 1000V. Current 50uA? to 1000A using test coil. Deviation control along readout. 0.0035% basic dc accuracy. 0.03% basic ac accuracy. Supplied with RS232 interfaces. UKAS/NIST Traceable
-
product
Programmable DC Power Supply
CBCT
The CBCT is a variable voltage DC power supply designed specifically to test substation circuit-breaker Open and Close coils. The CBCT uses the substation’s DC power supply to electronically generate a programmable output voltage from 5% to 95% of the source voltage. The CBCT can maintain up to an 80A test current while maintaining 2% or better voltage regulation during the circuit breaker coil operation.
-
product
18 GHz Latching SPDT
Part No.s GRF121, GRF121R
Extended- Centigrid hermetically sealed package, SMT straight-lead mounted, magnetic -latching SPDT, with grounded contacts, and a common coil negativeBandwidth: DC - 18GHzSignal Integrity: 40GbpsAvailable options include:GRF121R - common coil positiveResistive: 0.25A /28Vdc
-
product
Fluxmeter
480
The Model 480 is a laboratory grade fluxmeter, for use with a Helmholtz coil or custom search coils. This instrument measures the total flux of a magnet part, which can be related to the magnetic field strength. Applications include magnet testing, magnetizing, and automated field measurement. In order to provide accurate and repeatable measurements, automatic or manual drift compensation is available to the user. A peak mode allows even the fastest magnetic pulse, such as those from a magnetizer, to be accurately measured. The Model 480 is also useful for measuring AC fields that are too high in frequency for a gaussmeter to detect. Relay outputs and an external reset input allow for simple automation functions to be implemented, while the RS232C and IEEE-488 ports permit advanced control of the fluxmeter via a remote computer or automation equipment.
-
product
3 Phase Choke Coils
Supreme Instrument Laboratories
Suitable for operation on 415 / 440 V, A.C. 50 Hz. Working on air gap separation by increasing / decreasing the air gap with the help of a hand wheel mechanism, mounted on thick wooden / bakelite sheet with castor wheels for easy transportation.
-
product
CDI Ignition Coil
An on-plug coil for use with Capacitive Discharge Ignition (CDI). Design and manufacture is in-house, so we can make the coil to suit your specific application. The information given here is for a typical coil. Many of the parameters can be tailored to a particular installation.
-
product
Selenium Surge Suppressor
Surge suppressors are used to protecting circuits from transients (sudden, brief increases in voltage). Transients of widely varying magnitudes are caused by such circuit components as motors, coils, magnets, relays, and transformers. They are found in all electrical systems and are notorious for damaging diodes, SCRs, transformers, triacs, and relay contacts.
-
product
Flexible Current Sensor Probe
CTA
The CTA current sensors convert ac current to an isolated 0-5A current with available ranges from 100A to 10,000A. Because the current sensors are flexible split core, installation is possible without shutting down the LV electrical supply, avoiding expensive down-time costs. Typical applications are retrospective energy monitoring in factories, offices buildings, process control data logging systems, where power, energy and current monitoring is important. Typical applications are factories, offices buildings, ac/dc VFD drives, welding, power conversion and power distribution. For all CTA current sensor models, a NIST/NPL (UKAS) traceable calibration certificate and certificate of conformance is supplied. All CTA sensors use UL94V0 or CSA approved materials. The CTA flexible current sensors are suited to permanent or semi permanent installation. The coil sensor is durable, lightweight, flexible and will easily clip-around a power cable. The 5A output from the CTA current sensor connects direct to installed metering, rotary metering or current transducers.
-
product
Helmholtz Coils
Helmholtz coils is a candidate test apparatus for low frequency magnetic field susceptibility testing on military equipment and subsystems. Use of this coils reduce electromagnetic compatibility (EMC) qualification tests time, and subject the equipment under test (EUT) to a relatively uniform field.
-
product
SIL Reed Relays
Series 105
• SoftCenter™ construction• Highest quality instrumentation grade switches• Encapsulated in a plastic package with internal mu-metal magnetic screen• Wide range of switch confi gurations -Form A, 1 Form B, 2 Form A, 1 Form C• Two pole relay requires the same board area as the single pole type• Dry and mercury wetted switches are available with the same pin configuration and footprint.• Many benefits compared to industry standard relays. Learn more here >.• Insulation resistance greater than 10E12 Ohms (1TOhms) for dry Form A devices• 5, 12 and 24 Volt coils are standard, with or without internal diode• 100% tested for dynamic contact resistance
-
product
Towing Dynamometer
RS-90K
RS-90K towing dynamometer is designed for testing Class A trucks and is the most full-featured, reliable and accurate towing dynamometer in the industry. The RS-90K is built with a heavy duty steel frame, heavy-duty industrial axles and rides on an air ride suspension. The RS-90K is designed to maintain 90,000 Newtons of constant drawbar pull and the ability to simulate an uphill slope of 25%. The towing dyno uses absorbers with special high temperature coils powered by an industrial generator so there are no lead-acid batteries to charge and testing is unlimited at low speeds.
-
product
34945A Distribution Board, With Generic Screw Terminals For Driving 16 Switch Coils
Y1155A
The Y1150A-Y1155A distribution boards enable simple connections to the external switches. The distribution boards plug onto the 34945EXT and are used to route the power and control signals from the driver module to the switches using standard cables.
-
product
COMPUTERIZED AUTOMATIC RELAY TEST SYSTEM
CVRT-S16
CVRT-S8 & S16 are ideal for automatic testing of ELECTRO MECHANICAL AND READ RELAYS (only DC relays) both for static and dynamic characteristics. This system scans at one stroke, all the parameters of the relay as per definition of test procedure. The test sequence can be pre-programmed and stored in the disk. You can select the tests as per your requirement. Can include or exclude the test and you can have several options to match your test definitions. Semi skilled person can be engaged for actual testing, as he need not make any settings and need not interpret the readings. The system conducts the tests and gives PASS / FAIL indication on overall test results. If a printer is connected, each test result will be printed.Test Parameters : -> Coil Resistance.-> PickUp/Pull In /Operating Voltage or Current Linear Ramp Method or Step Method.-> Measure Pickup Contact Gap FBB-LBB V or mA-> DropAway/Drop Out/Release Voltage or Current Linear Ramp Method or Step Method.-> DropAway Contact Gap FFB-LFB V or mA-> % Release Dropaway/Pickup-> Contact Resistance of all contacts both Front and Back contacts.-> Operating Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while Operating @ above-> Release Time @ Set Voltage or Current.-> Contact Bounce or Chattering Time while release @ above-> Difference of Operate Time - Release Time.-> Bridging Test or Non Overlap Test.-> Transfer or Traverse Times while Operate and release.-> Operate Time @2nd Set Voltage or Current.-> Release Time @2nd Set Voltage or Current.-> Power Consumption @ Rated Voltage.-> Coil Current @ Rated Voltage at Room Temperature.-> Coil Resistance Corrected to 20deg C.-> Timing Waveform Graph for all active Contacts.
-
product
Rogowski Coil
INTEGRATORS FOR ROGOWSKI COILS
*High accuracy Class 0.5 (IEC 61869-2)*Combined with LEM ART & ARU class 0.5 Rogowski coils, they offer a universal metering and monitoring solution easily integrated with a monitoring device.*DIN rail mounted.
-
product
Coil Tester
It is a new impulse winding tester that incorporates high precision, a wide range of functions, various expandability, improved operability, and a full range of external communication interfaces.
-
product
Milliohm Meter
16502
Chroma Systems Solutions, Inc.
Basic accuracy : 0.05%Pulsed test current output mode is used to reduce thermal EMFs affection on milliohm measurementDC test current output mode is used to fasten measurement speed for inductive DUTDry-circuit test current output mode (limited Max. 20mV) is used to measure such contact resistances where the maximum open-circuit voltage must be limited to 50mVTemperature correction (TC function) regardless of material or temperatureUseful temperature conversion function for motor/ coil evaluation4 channels R scan with balance check function for fan motor (combined with A165017 option)0.001mΩ~1.9999MΩ wide measurement range with 4½ digits resolutionStandard RS-232 interfaceOptional GPIB & Handler interfaceBin-sorting functionComparator and pass/fail alarming beeper functionLarge LCD display (240 x 64 dot-matrix)Friendly user interface
-
product
Portable AC/DC Power Supply
UPS S3
The Vanguard UPS S3 is an AC/DC adjustable output power supply designed to operate substation circuit breakers. The UPS S3’s AC and DC voltage sources can supply up to 10 Amperes during the circuit breaker coil energization and circuit breaker charging motor operation. Powered by a single phase 90-120 Vac voltage source, the UPS S3 provides an isolated adjustable AC/DC voltage source. Output voltages are variable via the front panel control knob.
-
product
AC DC Current and Voltage Converters
The DAT5023 I is an AC or DC current converter, the input current range is selectable on order from 0-5Amps, 0-10Amps, 0-20Amps, 0-25Amps, 0-30Amps, 0-40Amps, 0-50Amps, 0-60Amps. It measure the current with the use of a Hall effect transducer. There is a coil (current transformer) inside the current converter which is isolated from the current input. The cable passes through the housing of the converter and the coil and the true root mean square measurement is taken from this coil then converted to a standard industrial signal output.
-
product
Automotive Ignition Coil Pulser and Tester
Zapper
Automotive Diagnostics and Publishing
The Zapper Automotive Ignition Coil Pulser and Tester is meant to allow you to activate and pulse all kinds of ignition coils on a bench. Test all available coils found on the market today. The Zapper coil testing bed and pulser allows testing of COP or Coil On Plug, DIS, Distributor Coils, Coil Packs and any other coil system. It also allows testing of COP coils with internal driver within the coil. The Zapper is a unique tool and all you'll ever need to test and diagnose ignition and misfire problems.
-
product
Rotary Scale Clamp Meter
1010 CL
Standard Electric Works Co., Ltd
● Rotary scale which presents only one scale in windows at one time to avoid any possible reading errors.● Pointer lock function freezes the reading in dimly lit or hard to reach places.● Ω range ideal for checking the continuity or relays, transformers and motor coils.● TAUT BAND movement.
-
product
Impulse Voltage Generator
Hilo-Test manufactures Surge generators for surge voltage and safety tests as well as for testing the insulation withstand voltage, the waveform in accordance with IEC 60060. Especially for EMC tests on photovoltaic systems and surge voltage tests, for example, to relay, capacitors, coils.
-
product
Power Supply
High precision analog control loop power supplies for inductive loads such as electromagnets, superconducting coils, Helmholtz coils and others.Autonomous analog power supplies with digital controls, readouts and supervision. The interfaces are digital and analog
-
product
Rogowski Coil
ART Series
*Class accuracy 0.5 conductor centered according to IEC 61869-10*Better than 0.75% accuracy regardless of the primary conductor’s position*Rated insulation voltage 1kV CATIII
-
product
Relay Buddy PRO Test Kit
191
Relay Buddy is a quick go / no-go tester for the most common automotive relays. With the included adapters, Relay Buddy now tests 5 different relay types and also tests shielded relays. Relay Buddy provides you with an indication of the general health and functioning of the relay switch contacts and coil. It will check the control side of the relay by applying a signal to the relay coil while it checks for proper functioning of the relay contacts. Relay Buddy operates the relay several times during each test session as it watches for consistency in every cycle. Relay Buddy will fail the relay and light the RED LED if any one of the cycles proves unsuccessful during the test session.
-
product
IGNITION COIL TESTER - ORANGE
MD76500M
*Non-intrusive, quick check tool instantly verifies active or inactive coil operation*Detects the magnetic field created by a coil energizing*Tool can be used to test coil on plug, coil near plug and coil pack systems
-
product
Spring Testing Machine
This machine is designed to test laminated springs and coil springs. The test is held under laminated springs and coil springs. The Cabinet comprises of the hydraulic unit, the hand wheel of the pump and the release valve handles are outside the cabinet for easy operation. This compact base carrier two fixed upright and four horizontal plates. The first and the third plates with two small uprights from an adjustable frame. The second and the fourth plates are fixed. A square threaded wheel arrangements provided for adjusting the height of the springs.
-
product
Single Variable Choke Coils
Supreme Instrument Laboratories
Suitable for operation on 220 / 240 V, A.C. 50 Hz. working on air gap separation by increasing / decreasing the air gap with the help of a hand wheel mechanism, mounted on thick wooden / bakelite sheet with castor wheels for easy transportation.
