Filter Results By:
Products
Applications
Manufacturers
Gold
invaluable naturally occurring material able to withstand corrosion, highly conductive. AKA: Au
See Also: Precious Metal, Platinum, Au, Gold Test
- Virginia Panel Corporation
product
Signal, Contact, ITA, QuadraPaddle, 5 Amp, 22-24 AWG
610138109
Primary mating contact 610138216. (May mate with other ITA contacts, as well.)Available in twin-female, crimp/solder, twin male, and wire-wrap design, QuadraPaddle contacts are engineered for flexible interconnect options. Rated at 5 amps continuous (1250 VAC) with a 2-ounce insertion force, QuadraPaddle contacts provide 4 reliable points of contact per pin, outstanding electrical performance, and low mating force.Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BrassContact Plating 30µ” Au over 100µ” NiContact Termination Crimp/SolderCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force (lbs.) 0.24
-
product
The Gold Standard for Breast Screening & Biopsy Training
Mammography QA Solutions
When the USA mandated Mammography QA requirements via the Mammography Quality Standards Act (MQSA), medical physicists, the ACR and the FDA worked with Gammex to complete the phantom design known today as the 156 Phantom.
-
product
S-100 Bus, Vectorbord Plugbord
8801-1
VECTOR Electronics and Technology, Inc.
100 Gold plated edge contacts (50 each side) on 0.125"(3.175mm) centers. No circuit pattern edge contacts only. Unrestricted component placement over entire board surface
-
product
Power Supply
NZXT HALE90 850w
*80+ Gold certified: The HALE 90 series from NZXT operates atultra high efficiency, at 20%, 50% and 100% loads, efficiencies are87%, 90%, and 87% respectively.*Single140mm two ball-bearing fan operates with minimal noiseeven at full load. Maximum decibel levels are 20db for wattagesbetween 550-750W and 30db for 850W and above.*Strong Single Rail Design: A single +12V rail provides stabilityand ease of use making the most out of your power supply. Offers stable & clean current delivery under heavy load.*Modular cable design: Modular cable design allows the user topick and choose which cables they want to use, optimizing cablemanagement and airflow inside the chassis. Flat cables allow for easier routing and bending inside the computer chassis during wire management.
-
product
Coax, Contact, Receiver, 75 Ohm, RG179
610104157
Primary mating contact 610103169. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Female & Male Shield – brassCenter Contact – BeCuContact Plating Center Conductor Shield – 30µ” Au over 100µ” NiContact Termination Center Conductor – Crimp or SolderShield – CrimpInsulator PTFEMating Force 4.0 lbs max [1.81 kg]Electrical SpecificationsCharacteristic Impedance 75 ΩFrequency Range DC to 3 GHzVSWR < 2.95 @ 3 GHzInsertion Loss -1.64 @ 3 GHzDWV 800 VRMSContact Resistance Center Contact - 5 mΩOuter Shield - 3 mΩCable Specifications RG179Environmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition AInsulation Resistance 1000 MΩ min.
-
product
Low Current Switching Relay
D-E Series
Heavy duty relays for demanding applications, suitable for low current switching, equipped with gold plated contacts.
-
product
Coax, Contact, Receiver, 75 Ohm HD, sm59/U Belden 1855A, 3 GHz
610102133
Primary mating contact 610102132. (May mate with other ITA contacts, as well.)Mechanical SpecificationsDurability 20,000 cyclesContact Material Female & Male Shield – BrassCenter Contact – BeCuContact Plating Center Conductor Shield – 30µ” Au over 100µ” NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 2.0 lbs max [0.91 kg]Electrical SpecificationsCharacteristic Impedance 75 ΩFrequency Range DC to 3 GHzVSWR ≤ 2.26 @ 3 GHzInsertion Loss -0.86 dB MaxDWV 1500 VDC min.Contact Resistance 5 mΩ center/ 3 mΩ outer Cable Specifications sm59/U Belden 1855AEnvironmental SpecificationsOperating Temperature -55°C to +125°CVibration MIL-STD 1344, Method 2005, Test Condition 4Shock MIL-STD 1344, Method 2004, Test Condition EInsulation Resistance 1000 MΩ min.
-
product
DIY Connector Board
This Universal DIY connector board can be used with any connector. Simply drill holes into the brown mounting board and attach the connector(s) of your choice. Then, solder each contact to the main board.Easy to mount any connector (Either screw, bolt, or glue in place)Gold Plated contact pins for high reliabilityMany JTS 1mm, 1.5mm and 2mm connectors can be soldered directly to the main boardMade in the USA
-
product
Scientific CCD Image Sensors
Our front and backside illuminated (BSI) and backthinned Charge Coupled Devices (CCDs) are seen as the gold standard for scientific and quantum imaging in applications in spectroscopy, microscopy, In vivo, x-ray and astronomy. We understand that every imaging application is unique and requires our engineers and scientists to work closely with our customers providing highly tailored imaging solutions.
-
product
Coax, Contact, ITA, 20 GHz, RG 223, Crimp, 90 Series Modules only
610102117
Primary mating contact 610102116. (May mate with other ITA contacts, as well.)20 GHz coax contacts have an impedance of 50 Ohms and a current rating of 5 amps.It is recommended to use SF142 to achieve 20 GHz and RG223 to achieve 12 GHz.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination Shield – Crimp/ClampInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 20 GHzVSWR 1.15 + .01 (f) GHz w/ RG142 (8 GHz)1.15 + .01 (f) GHz w/ SF142 (20 GHz)Insertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications RG 223 Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Mini Coaxial Contact, Receiver, RG316 Double Shield
610104149
Mini Coaxial Contact, Receiver, RG316 Double Shield.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC to 1 GHzVSWR ≤ 1.06 @ 1 GhzInsertion Loss 1.2 dB @ 1 Ghz1.02 dB @ 500 MhzDWV 1500 VDC Min.Contact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications RG316 Double ShieldEnvironmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
product
Signal, Contact, TriPaddle, Receiver, 5 Amp, .025" Round Post
610110179
Primary mating contact 610110113. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous (20 AWG)600 Volt Max. use of wire Mil-W-16878/4Contact Resistance 4 mOhms Max.Measured at 50 mV @ 100 mAAVG Mating Force(lbs) 0.41Dielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 4000 MOhms Min.Contact Body BeCuContact Plating 30µ” Au over 100µ” NiCycle Life 20,000 Cycles
-
product
Plugbord
3682-2
VECTOR Electronics and Technology, Inc.
44 Gold plated edge contacts (22 each side)on 0.156"(3.96mm) centers.Interleaved buses pattern on wiring side only solder- coated for user convenience.Bus outline silkscreened on component side to facilitatecomponent placement. Mounts DIPs with 0.3”, 0.4” & 0.9” lead spacing. Unclad test point area at top of board Row and column legends provided
-
product
Signal, Contact, Receiver, QuadraPaddle, 5 Amp, 22-28 AWG, Crimp, 30µ" Au
610138216
*Please note: The difference between this p/n and 610138116 is the amount of gold plating. See below.P/n 610138116- 50µ" AuP/n 610138216- 30µ" AuPrimary mating contact 610138109. (May mate with other ITA contacts, as well.)Specifications Operating Voltage & Current 5 Amps Max. Continuous; 600 volt Max. use of wire Mil-W-16878/4Contact Resistance 25 mOhms Max.Measured at 50 mV @ 100 mADielectric WithstandingVoltage (DWV) 1500 VDC Min.Insulation Resistance 5000 MOhms Min.Contact Body BeCuContact Plating 30µ" Au over 100µ" NiContact Termination CrimpCycle Life 20,000 CyclesRoHS Directive 2011/65/EU Status CompliantREACH Article 33 Status CompliantECHA Article 59 of Reach Regulation CompliantAVG Mating Force(lbs) 0.24
-
product
Coax, Contact, ITA, 20/26 GHz, 3.5MM, w/ SMA Adapter, 90 Series Modules only
610102134
Coax, Contact, ITA, 20/26 GHz, 3.5MM, with SMA Adapter (90 Series modules only)Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – brassCenter conductor – BeCuContact Plating 30µ" Au over 100µ" NiContact Termination 3.5mm compatibleInsulator PTFEMating Force 3.0 lbs max [1.36 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 26 GHzVSWR 1.15 + .01 (f) GHzInsertion Loss .06 x√f(GHz) dBDWV 800 V RMS Shield to center contact1000 V RMSContact Resistance 5 mOhms center/ 3 mOhms outer Cable Specifications 3.5mm compatibleEnvironmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MΩ min.
-
product
PowerTrain Simulators
NMEA 2000
The Au NMEA 2000 PowerTrain simulators V1.00A release can generate majority of NMEA 2000 PowerTrain Controller Area Network (CAN) signals on a NMEA 2000 network. Au NMEA 2000 PowerTrain simulators are designed very easy to use. All editions run independently (without personal computer). It is widely used as valuable tools for any situation from product-line test, incoming inspection, business demonstration to product development and product validation.
-
product
Voltage Controlled Oscillators
a High Reliability Low Noise Voltage Controlled Oscillator (VCO) which covers a 10 MHz to 20 MHzfrequency band with a voltage tuning range from 0V to 20V. This design features exceptional phase noise performance of -120dBc/Hz @ 10 kHz offset. Supply Voltage is +15V with a generated output power level of +10 dBm and 2nd harmonic output of-11 dBc typical. The assembly is RoHs compliant and available in a compact 0.5 inch SMT package with an industry standardmounting footprint. The bottom surface is copper clad with 2-5 micro inches of immersion Gold over 150 - 250 micro inchesof Electro less Nickel which makes it resistant to oxidation for ease of soldering. The VCO operates over a temperature rangeof -40°C to +85°C and is designed to meet a variety of MIL-STD-202 test conditions including Humidity, Shock, and Vibration.
-
product
RF/Microwave Assembly Capability
Teledyne Labtech offers a comprehensive build-to-print microwave module and microwave components manufacturing service. This includes MMIC placement, Au wire bonding, SMT assembly and test.
-
product
Wide Jaw Kelvin Lead Set
6730
Wide Jaw Kelvin Lead Set. True wire four wire lead set with gold plated alligator clips that open to a wide .800? (20.3mm).
-
product
AC To DC Power Supply: 12V 25A
#TPS120
AC to DC Power Supply: 12V 2.5A with intl adapter plugs for (NA, EU, AU, UK), 849160008446
-
product
Salt Contamination Meter
130
Key features of the Elcometer 130 Salt Contamination Meter include: Fast reading rate allows multiple conductivity tests to be completed efficiently Pressure plate ensures a constant and uniform pressure to paper Automatic detection of paper size and automatic adjustment of reading value USB and Bluetooth® data output to ElcoMaster® software Dust and water resistant rugged design equivalent to IP64 Automatic temperature compensation ensures accurate results Non-oxidising gold plated contacts ensures lifetime accuracy Stores up to 150,000 readings in 2,500 alpha numeric batches Fully portable hand-held, ergonomic design ideal for use in the field
-
product
Multibus Extender
3690-18
VECTOR Electronics and Technology, Inc.
Length : 7.65"(190.5 mm)Height : 12.0"(304.8 mm)Contacts : 30 Contacts each side on 0.100" centers 43 Contacts each side on 0.156" centersConnector : Gold plated, mounted on top and connected to circuit tracesCurrent Rating : 5 amps at 10°F rise
-
product
Connectors, Header - Female
INT-10140
1x40 pin female header. These headers mate with square-pin 0.1" male headers. They can be cut into smaller segments, but please note that they are not break-away and at least one pin will be lost with each cut. Gold plated and RoHS compliant.
-
product
SMT & THRU HOLE LOADED BOARD TEST PROBES
SERIES 33
ElectricalMAXIMUM CURRENT:3 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,20 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24Kt gold plated over nickelBARREL: Nickel silver with preciousmetal clad ID.SPRING: Music wire, silver plated
-
product
PCIe and VPX Compatible Adapter Carrier
PCIe2VPX3UX4
The power supply designs utilize switching regulators controlling MOSFET´s. An LC filter insures clean power at the VPX device. The PCIe gold fingers are rated for 1.1A each, and a total of 5.5A on the +12V rail. 55W are available to the card after power conversion.
-
product
Probe Card PCB's
DTS offers both generic and custom PCBs blanks for probe cards. Probe card PCBs are available for all tester platforms and can be configured for any vertical technology, epoxy cantilever and legacy blade cards. DTS probe card blanks are made to precise specifications required for all probing technologies and are available in high speed and high temperature materials. All probe card PCBs employ a balanced layering construction to maintain tight flatness specifications and minimize warping, allowing good probe planarity. Gold plating on all surface metals facilitates easy soldering and minimizes probe resistance. DTS is continually adding new probe card blanks to its library!
-
product
Extender
3690-15
VECTOR Electronics and Technology, Inc.
Contact fingers at the other end of extender card are gold plated provides low insertion force and positive contact with printed circuit boards.
-
product
Mini Coax, Contact, ITA, Solder Sleeve, RG316 & RG178
610103140
Mini Coax, Contact, ITA, Solder Sleeve, RG316 & RG178.Mechanical SpecificationsDurability 20,000 cyclesContact Material Shield – BrassCenter Conductor – BeCuContact Plating Shield – 50µ" Au over 100µ" NiCenter Conductor – 60µ" Au over 100µ" NiContact Termination Solder SleeveInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50 ΩFrequency Range DC to 2 GHzVSWR ≤ 1.2 @ 2 GhzInsertion Loss ≤ 0.05 dB @ 500 Mhz≥ -0.3 dB @ 2 GhzDWV 1500 VDC Min.Contact Resistance < 5 mΩ @ 0.5 Amp & always < 10 mΩCable Specifications RG316 & RG178Environmental SpecificationsOperating Temperature -50°C to +105°CInsulation Resistance 1000 MΩ min.
-
product
Veterinary Hematology Analyzer
ABX Micros ESV 60
The Gold Standard of Veterinary Hematology Testing- Open Tube- 10 animal species- 8 or 18 parameters- 50 tests/hour- Highly compact and lightweight- Micro-sampling on whole blood: 10μL- Precise cellular identification through electronic impedance variation method- Haemoglobin measurement with photometry
-
product
LUTHER & MAELZER BARE AND LOADED BOARD TEST PROBES
SERIES LMP 60
MechanicalMINIMUM CENTERS: .100 (2.54)FULL TRAVEL: .160 (4.06)WORKING TRAVEL: .107 (2.72)OPERATING LIFE: 1,000,000 cyclesElectricalMAXIMUM CURRENT: 5 amps continuousat working travel, non-inductiveRESISTANCE: At 35 mA test current,35 mOHMS meanMaterials and FinishesPLUNGER: Heat treated berylliumcopper, 24 Kt gold plated over nickelBARREL: Nickel silver, 24 Kt goldplated over nickel
-
product
Cantilever Probe Card
MPI Cantilever Probe Card is widely applied on gold bump and pad wafer testing for display driver, logic, and memory device. MPI’s cantilever probes are the corresponding answer to the demands of fine pitch, small pad size, high speed, less cleaning, multi-DUT, high pin count, and ultra-low leakage requirements. With outstanding craftsmanship, innovative architecture and proven methodologies based on mechanical and electrical simulation/measurement results, making MPI the top cantilever provider worldwide.
