Filter Results By:
Products
Applications
Manufacturers
IEPE
standard for accelerometers.
-
product
PCB High Sensitivity, 100mV/g, ICP® (IEPE) Accelerometer
780989-01
The PCB HSTC33 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB HSTC33 features a sensitivity range of 100 mV/g and requires a low-noise coaxial cable.
-
product
Low Outgassing ICP® Accelerometers
Low Outgassing ICP® (IEPE) Accelerometer Types & Their Applications.
-
product
Charge Amplifier
ZET 440
Charge amplifier ZET 440 for piezoelectric detectors is intended for:*amplification and conversion of output signals of primary piezoelectric transducers with charge output;*amplification and conversion of output signals of primary transducers with the IEPE type in-built electronics to voltage;*gain ratios: 1, 10, 100;*LPF: 0.1, 1, 10 Hz
-
product
Vibration Monitoring
Encore Electronics offers a full line of vibration monitoring equipment, ranging from DIN-rail mounted accelerometer signal conditioners to complete multi-channel monitor / alarm cabinets. Most are equipped with a 4mA power source for IEPE (Integral Electronic Piezo-Electric) transducers.
-
product
Force Sensors
Our force sensors are indicated for use in modal and structural analysis, process control, and general-purpose dynamic force measurements. See our range of charge modes and IEPE force sensors.
-
product
IEPE Monoaxial Accelerometer – 100 mV/g
HDP352C34
Monoaxial accelerometer general purpose, ICP, 100mV/g, weight 5,8 g, range 50 g pk
-
product
Special Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
This page shows vibration sensors for special applications.The Seat Pad Accelerometer Model KS963B100-S was developed for measuring whole body vibration transmitted by driver seats of building machines and other vehicles in compliance with ISO 10326-1 and ISO 7096. The sensor has an IEPE output for robust signal transmission.
-
product
PCB IMID01, 100 mV/g, IEPE, 2-Pin, Accelerometer, Industrial Vibration Sensor
784175-01
The PCB IMID01 is an industrial Vibration Sensor designed for permanent installations. This sensor helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. The PCB IMID01 features a sensitivity range of 100 mV/g and uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The sensor supports the IMI Industrial Accelerometer Cable as well as the MIL2M-Breakout Cable.
-
product
IEPE Triaxial Accelerometer – 1000 mV/g
HDP356B18
Triaxial accelerometer high sensitivity, ICP, 1V/g, weight 25g, range 5 g pk
-
product
Universal Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
There are models with charge output and with IEPE compatible voltage output. The transducers of KS series have a shear type sensing element making them less susceptible to thermal transients and base strain. The accelerometers of KD series have a compression type sensing element combining rugged design, precision and low cost.
-
product
PCB GPTC03, 10 mV/g, IEPE, Accelerometer, General-Purpose Vibration Sensor
780988-01
The PCB GPTC03 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the … Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB GPTC03 features a sensitivity range of 10 mV/g and requires a low-noise coaxial cable.
-
product
PCB TA01, 5 mV/g, IEPE, Accelerometer, Triaxial Vibration Sensor
780990-01
5 mV/g, IEPE, Accelerometer, Triaxial Vibration Sensor - The PCB TA01 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB TA01 features a sensitivity range of 5 mV/g.
-
product
USB Sound And Vibration Measurement Bundle
The USB Sound and Vibration Measurement Bundle provides a portable, USB-based sensor measurement system that helps you measure signals from integrated electronic piezoelectric (IEPE) and non‑IEPE sensors such as accelerometers, tachometers, and proximity probes.
-
product
Signal Conditioning
To get most out of high-quality sensors, accurate, low-noise processing of the sensor signals that are emitted is essential. Kistler offers an attractive portfolio of solutions for signal processing and subsequent data digitization. Piezoelectric (PE) sensors with a charge output require a so-called charge amplifier. On the other hand, piezoelectric sensors with integrated electronics (IEPE) are supplied by Piezotron couplers which decouple and amplify the signal.
-
product
IEPE Impact Hammers
Our range of general purpose IEPE impact hammers offer a range of great cost effective solutions for a majority of applications requiring the excitation of a structure. The most common application being Modal testing whereby the structure is excited using the impact hammer and the response of the structure is measured using accelerometers. However instrumented hammers can also be used for crack detection and other structure related investigations.
-
product
SIRIUS Waterproof
SIRIUS Waterproof - Rugged and Modular Data Acquisition SystemExtremely rugged (IP67 degree of protection) and fully isolated rugged data acquisition system for the most demanding testing in harsh environments. High-precision, high-dynamic, and high-bandwidth for all types of analog signals from IEPE to strain gages.
-
product
IEPE Triaxial Accelerometer – 10 mV/g
HDP356A02
Triaxial accelerometer miniature for hand-arm measurement, ICP, 10mV/g, weight 4g, range 500 g pk
-
product
Digital Telemetry Solutions
For measurements on rotating components and moving machinery, imc offers modern telemetry systems for a wide variety of tasks: whether single-channel torque monitoring of a rotating shaft, multi-channel strain gauge and temperature measurements on a train wheel-set or non-contact power measurement on a vehicle drivetrain in harsh environments. There are transmission electronics available for a large variety of sensors, such as strain gauge (quarter-, half- and full-bridge), thermocouples, PT100/1000, as well as IEPE sensors and voltage signals.
-
product
IEPE Triaxial Accelerometer – 1000 mV/g
HDWBV-100
IEPE tri-axial accelerometer for the measurement of vibration transmitted to whole body.
-
product
Digital USB Sensor Interface AC,DC, IEPE
ROGADAQ2
The RogaDAQ2 USB DAQ is developed for highly accurate measurements in the T&M and also for NVH measurements. This USB Front End is optimized for noise and vibration measurements with 2 channel IEPE (ICP®) sensor supply.
-
product
FD-11634, 8-Channel Sound and Vibration Input Device for FieldDAQ
786471-01
The FD-11634 can measure signals from integrated electronic piezoelectric (IEPE) and non-IEPE sensors such as accelerometers, tachometers, and proximity probes. The device also works with smart TEDS sensors, delivers a wide … dynamic range, and incorporates software-selectable AC/DC coupling and IEPE signal conditioning. The input channels simultaneously measure signals and have built-in anti-aliasing filters that adjust to your sample rate. This device is IP65/IP67-rated to be dust-tight and water-submersible and can sustain 100 g shock and 10 g RMS vibration in -40°C to 85°C environments. You program the FD-11634 with NI-DAQmx, which automatically synchronizes multiple FieldDAQ™ devices. When used with NI software, this device can provide processing functionality for condition monitoring such as frequency analysis and order tracking.
-
product
PCB GPTA02, 10 mV/g, IEPE, 1 Hz to 5 kHz, Accelerometer, Triaxial Vibration Sensor
784169-01
The PCB GPTA02 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB GPTA02 features a sensitivity range of 10 mV/g and requires a 4-socket plug-to-3 BNC plug cable.
-
product
"Smart" Dynamic Signal Analyzers
EMX-4xxx
The EMX-4xxx product family contains high-performance breakout boxes (EMX-4008 and EMX-4016), smart high density dynamic signal analyzers (EMX-4250 and EMX-4251), smart PXIe 625 KSA/s 4-channel digizers (EMX-4350), and charge and IEPE PXIe 625 KSA/s 4-channel digitizers (EMX-4380).
-
product
Compact IEPE Sensor Interface
Plug.n.DAQ Lite
ROGA Instruments Plug.n.DAQ Lite is a compact IEPE sensor interface for linux or windows with 2 input channels. It offers the USB PC interface and requires no drivers for installation. The operating system such as LINUX or Windows recognizes the device as an external usb audio card.
-
product
NI-9231 and cDAQ-9171 USB Sound and Vibration Measurement Bundle
865665-01
NI-9231 and cDAQ-9171 USB Sound and Vibration Measurement Bundle - The USB Sound and Vibration Measurement Bundle with NI-9231 and cDAQ-9171 includes the NI-9231 C Series Sound and Vibration Input Module and the cDAQ-9171 CompactDAQ Chassis for sound and vibrations measurements. This bundle provides a portable, USB-based sensor measurement system that helps you measure signals from integrated electronic piezoelectric (IEPE) and non IEPE sensors such as accelerometers, tachometers, and proximity probes. The included NI-9234 features 8 channels with built-in anti-aliasing filters that automatically adjust to your sample rate. Additionally, the bundle supports simultaneous sampling and high dynamic range measurements necessary for modern measurement microphones and accelerometers.
-
product
PCB High Sensitivity, 100mV/g, ICP® (IEPE) Accelerometer
784170-01
The PCB HSTA15 helps you acquire sound and movement data with supported PXI Sound and Vibration Modules, C Series Sound and Vibration Input Modules, and USB-based Sound and Vibration Devices. This sensor uses the Integrated Electronics Piezo-Electric (IEPE) current excitation. The PCB HSTA15 features a sensitivity range of 10 mV/g and requires a 4-socket plug-to-3 BNC plug cable.
-
product
Transducer Calibration
m+p SensCal
Regular transducer calibration is an essential requirement for maintaining the accuracy, reliability and repeatability of the results obtained from a measurement system. m+p international’s m+p SensCal program provides a quick and simple process for calibrating accelerometers (piezo-electric with charge output or IEPE, piezo-resistive, capacitive) in your laboratory, as well as velocity or displacement transducers.
-
product
Signal Conditioners
Metra Mess- und Frequenztechnik in Radebeul e.K.
Metra has been manufacturing amplifiers for piezoelectric transducers for over 50 years. We offer economic charge amplifiers and signal conditioners for IEPE transducers including microphones.
-
product
USB-4432, 102.4 kS/s, 100 dB, 0.8 Hz AC/DC Coupled, 5-Input Sound and Vibration Device
780421-01
The USB-4432 is designed for sound and vibration measurements. Four of the input channels incorporate integrated electronic piezoelectric (IEPE) signal conditioning for accelerometers and microphones and built-in antialiasing filters that automatically adjust to your sampling rate. The fifth input channel does not include IEPE support.
-
product
ECAT MiniModules
AD4 ECAT MM Series
Designed specifically for use with IEPE sensors. With up to 100 kHz per channel, the high-speed EtherCAT® measurement modules simplify your application.
