Filter Results By:
Products
Applications
Manufacturers
Magnet
Attract iron and are surrounded by a magnetic field.
-
product
Relay / Magnetic Field Testers
PeakTech Prüf- und Messtechnik GmbH
Ideally suited for checking magnetic fields and the correct function of coils, e.g. Relays and solenoid valves. The magnetic field detector works without contact, so that opening the housing is not necessary in most cases. When a magnetic field is detected, the probe tip lights up permanently blue, with clocked relays in the same cycle as they are controlled. The function of the magnetic field detector can be checked before each measurement with the enclosed test permanent magnet.
-
product
Magnetizer
MAGSYS magnetizers allow the magnetization, adjustment and also the demagnetization of isotropic and anisotropic magnetic materials of different sizes. In particular, all highly coercive magnetic materials, such as Sm2Co17 or plastic-bonded NdFeB magnets, can be magnetized easily and with short cycle times. In addition to raw magnets, e.g. directly after production, complete workpieces with magnets already installed can also be magnetized.
-
product
Hall Effect Measurement Equipment
HEM
The physical quantity of Hall Coefficient, Hall Mobility and Carrier Density etc. can be investigated by measuring at room temperature voltage occurred perpendicularly to the both magnetic field and constant-current when flowing constant-current perpendicularly to magnetic field from current source while applying magnetic field to sample set at the center of magnetic field of magnet.
-
product
Variable Power Supply
VS3
The VS-3 power supply is a very convenient portable, non-isolated “variable source” from 0 volts to 150 Vac or 0 volts to 150 Vdc and rated for up to 3 amps, thus the name VS-3. It is comprised of an illuminated voltmeter that reads to the first significant digit, AC variable system output voltage, DC variable system output voltage, logic output voltage and one sense (continuity) contact monitoring points. Banana jacks for connection of test leads are spaced at intervals that allow the use of dual banana test plugs if desired. The VS-3 is protected by two levels of overcurrent protection; AC input, and ground fault protection by a GFCI. All circuitry is housed inside a custom designed case made from 16 gauge steel. An Internal fan dissipates heat buildup and exhaust through louvered side vents built into the case. The carrying handle is designed with a “spring return to rest” position and is padded for comfort. The case has been sized for optimum portability and is balanced from the handle during transportation. The case has a powder coated finish that is scratch, chemical and weather resistant. Rubber padded feet support the case when in the upright position and a convenience receptacle is located on the side of the case. A unique feature of the VS-3 is that it contains “Magnet Packs” on the back of the case. These “Magnet Packs” can support the VS-3 and allow it to “hang” from any magnetic metal surface. The VS-3 can be powered by our UPS system, eliminating the need for an extension cord. The ability to magnetically attach the VS-3 near the source of connection and eliminating the need for an extension cord makes the VS-3 a “must have tool” for technicians.
-
product
Fluxmeter
480
The Model 480 is a laboratory grade fluxmeter, for use with a Helmholtz coil or custom search coils. This instrument measures the total flux of a magnet part, which can be related to the magnetic field strength. Applications include magnet testing, magnetizing, and automated field measurement. In order to provide accurate and repeatable measurements, automatic or manual drift compensation is available to the user. A peak mode allows even the fastest magnetic pulse, such as those from a magnetizer, to be accurately measured. The Model 480 is also useful for measuring AC fields that are too high in frequency for a gaussmeter to detect. Relay outputs and an external reset input allow for simple automation functions to be implemented, while the RS232C and IEEE-488 ports permit advanced control of the fluxmeter via a remote computer or automation equipment.
-
product
Selenium Surge Suppressor
Surge suppressors are used to protecting circuits from transients (sudden, brief increases in voltage). Transients of widely varying magnitudes are caused by such circuit components as motors, coils, magnets, relays, and transformers. They are found in all electrical systems and are notorious for damaging diodes, SCRs, transformers, triacs, and relay contacts.
-
product
Cryocoolers
Cryogenic uses various cryocoolers with cooling powers to suit different cryogen free magnet systems and applications. The Gifford-McMahon cycle cryocooler has the advantage of greater thermodynamic efficiency. The pulse-tube cryocooler is vibrationally quieter, has a longer service interval and cools faster from room temperature.
-
product
Magnetic Field Tester
MS-440
This device recognises fast and simply magnetic fields generated by electric reels and permanent magnets.
-
product
Elevator Drives
User friendliness is the emphasis of our drives. The keypad interface and programming are dedicated to elevator and escalator applications. The performance features are well-suited for both Induction and Permanent Magnet motors with the latest control functions.
-
product
Rotor Tester
Dr. Brockhaus Messtechnik GmbH & Co. KG
The rotor tester system determines the symmetry of multipolar magnetized DC permanent magnet rotors.
-
product
SparkFun Triple Axis Magnetometer Breakout
MLX90393 (Qwiic)
It's time to start utilizing the superior magnetometer, and what better way than to throw it onto an easy-to-use breakout board? The SparkFun MLX90393 Magnetometer Breakout is a triple-axis magnetic sensor board capable of sensing very small fields, while still behaving as one would expect during saturation in larger fields (like a nearby magnet). The MLX90393 breakout can be used as a compass sensor but also works well as a non-contact controller, a flow meter with a magnetic impeller, or a linear actuator position sensor. To make it even easier to to get your readings, all communication is enacted exclusively via I2C, utilizing our handy Qwiic system. However, we still have broken out 0.1"-spaced pins in case you prefer to use a breadboard.
-
product
Microwave Devices
Photonis Defense and its predecessors have been designing and manufacturing Traveling Wave Tubes (TWTs) since their invention in the early 1940’s. Photonis manufactures helix-type tubes that are constructed using the industry standard metal-ceramic construction. Our tubes are conduction cooled and feature rare earth periodic permanent magnets for power-free focusing.
-
product
Magnet Testing
m-axis
m-axis is a measurement system that can be used to characterize permanent magnets in terms of their magnetic specifications (magnetic moment and magnetization angle) with high precision. In addition to the four standard measuring ranges, the modular design allows the system to be adapted to customer-specific requirements. The measurement systems can be used for 100% in-line quality control via our m-axis I/O module.
-
product
Non-Destructive Subsurface Layer Profiling
NMR-Mouse one-sided NMR
The unique, powerful Profile NMR-MOUSE® probe works hand-in-hand with the Kea2 spectrometer. The Profile NMR-MOUSE is a portable, open NMR sensor equipped with a novel permanent magnet geometry that generates a flat sensitive volume parallel to the scanner surface. The system can measure *Proton density as a function of depth *T2 NMR relaxation times *T1 NMR relaxation times *Self-Diffusion coefficient of liquids
-
product
Magnetic Speed Sensors
We offer the most comprehensive portfolio of magnetic speed sensors ICs, covering the full range of speed and speed with direction, two- and three-wire interface, magnetic encoder (ring magnet) and gear tooth sensing, Hall and GMR technology, and ASIL-compliant options for transmission, wheel speed, engine, e-motors, and many more encoder and gear tooth sensing applications.
-
product
Vector Field and Multi-Axis Systems
Cryogenic vector magnet systems allow precise alignment of the magnetic field to an exact direction in a measurement sample. The system provides the capability of orienting the magnetic field to any vector direction. This is suitable for experiments where samples cannot be moved easily.
-
product
Linear Hall Sensor
The output of a hall effect sensor is a voltage which changes in proportion to the shaft extension. A constant voltage is required across the supply and ground wires of the sensor. The sensor consists of a Hall Effect element, and a shaft which houses a magnet. When the position of the sensor changes relative to the shaft, the change in magnetic field in the sensor results in a change in output voltage.
-
product
Brushless Motor
Citizen Chiba Precision Co., Ltd.
*High output *The rotor uses Nd magnets. *The stator was designed for maximum output per unit volume to maximize winding.*Long service life *Since these are brushless motors, the only limit to service life is how long the ball bearings last.
-
product
Phase Indicators
Kyoritsu Electrical Instruments Works, Ltd.
New technology permits safe testing, without the need of direct contact between probes and live wires. The insulated crocodile clips can clip insulated cables from 2.4 to 30mm. Phase rotation is indicated by the rotary illumination of LEDs and logical audible tones. The instrument can be fixed to a metal panel via the magnet on the back side. Wide measuring range for 3 phase installations from 70V to 1000V AC. Super brightness function permits clear LED''''s indication also in sunshine. Complies with IEC 61010-1 CAT IV 600V and CAT III 1000V.
-
product
D.C. Recording Fluxmeter
TRF
This is the equipment being able to measure direct current magnetization property of wide-ranging magnetic materials from soft magnetic materials to high performance permanent magnet with magnetic flux meter based on M integral closed magnetic circuit system.
-
product
MM-Wave Sources From 36 To 178 GHz Based On BWO
Insight Product Company offers a BWO based MM-wave sources of radiation at frequencies from 36 Ghz to 178 Ghz. Each source includes millimeter-wave BWO tube and a specially designed permanent magnet system. BWO tube is installed inside the permanent magnet and does not require any adjustment by the customer. Offered sources are the most wide-banded, they are very reliable, small sized, powerful and easy to operate.
-
product
Melexis 90217 Hall-Effect Sensor
605-00005
Parallax has worked with the Melexis 90217 sensor in applications including CNC milling machine spindle speed measurement and feedback on motor RPM. With the CNC milling machine it reliably measured the top spindle speed of 7,500 RPM. This is a cost-effective and highly functional hall-effect sensor. The Melexis 90217 is designed to be used with a bias magnet (#605-00006) south facing the back (non-marked) side of the IC. With a single Hall plate, this sensor is immune to common rotary alignment problems. Very easy to interface with all microcontrollers.
-
-
product
GNSS & GPS Antennas
Our portfolio of GNSS and GPS antennas are available in a variety of mounting and placement options including adhesive, magnet, mounting hole, and direct mount. Our GNSS and GPS antennas are available in several antenna types, including external mount, enclosure, flexible PCB, patch, PCB, and stamped. Custom antenna developments are regularly undertaken to meet specific customer requirements. Our GNSS and GPS antennas portfolio includes products manufactured by TE Connectivity, Laird Connectivity External Antennas, and Hirschmann Car Communications.
-
product
Standard Helmholtz Coils
Helmholtz Coils are ideal for the measurement of Rare Earth (Samarium Cobalt, Neodymium) and Hard Ferrite permanent magnet materials (materials which exhibit a relative straight line demagnetization). Our standard Helmholtz Coils are for use with fluxmeters. The Helmholtz Coil measures the magnet sample as a single magnetic moment provided that the longest dimension of the magnet sample is less than one-third (1/3) the diameter of the coil system. By definition, the magnetic moment per unit volume is the intrinsic magnetization of the sample. With our calibrated Helmholtz Coil and Integrated Fluxmeter – and given the volume of the permanent magnet sample – the intrinsic open circuit operating B (Bdi) can be measured.
-
product
Battery Charger Meters
A range of ammeters and voltmeters with tough moving magnet or polarised moving iron movements designed for low cost indication of d.c. or rectified a.c.
-
product
Solid State NMR
Magnets for NMR experiments are required to have a high homogeneity, which can be maintained over a wide range of field. Experiments are performed at fixed frequency and the spectrum is obtained by sweeping the magnetic field. This requires the field to be stable in spatial homogeneity and change steadily and repeatedly over time.
-
product
Handheld RH Meter
635-1
The Edgetech Instruments Model 635-1 is a robust and reliable measuring instrument with the protection class of IP54. The large back lit display allows the user to easily view the dew point, RH and temperature readings. The 635 offers both standard plug-in probes and optional wireless probes that can measure up to a distance of 20 meters. A maximum of 3 wireless probes can be used at one time and can be retrofitted with the 635 at anytime. All probes are equipped with a patented humidity sensor offering long term reliability and guaranteed accuracy based on results from worldwide laboratory tests. The 635 is equipped with a secured carrying strap for safe transporting and has heavy duty magnets on the back to ensure secure attachment at the measuring location.
-
product
Magnet Temperature Characteristics Apparatus
TDF
Evaluation of thermal stability of varieties of permanent magnets including rare-earth permanent magnet. TDF-5-200auto This apparatus automatically measures and analyzes reversible temperature coefficient(a) and irreversible temperature coefficient (Flux loss ?f) of magnetic flux density of rare-earth permanent magnet in the wide range from low to high temperature.
-
product
Magnet Testing
m-cat
m-cat is a magnetic field mapper for magnetrons which measures the magnetic stray field data of magnetrons on all three spatial axes and also calculates geometric data. This allows sputtering processes to be monitored and optimized, since the setting or status of the magnetron is critical to the subsequent outcome of the coating process.
