Filter Results By:
Products
Applications
Manufacturers
Mainframes
Fully capable housing with power, cooling and emi protection ready to operate with the addition of instruments.
- Scientific Test, Inc.
product
Semiconductor Tester
5000E
Current Ranges:Standard: 2.0nA – 50AUp to 100A with Mainframe ExtensionVoltage Ranges:Standard (anode): 10mV – 1000V2000V with 2kV Anode OptionStandard (gate): 10mv – 20V80V with 80V Gate Option
-
product
1.5 M 50-pin D-Sub Cable
Y1135A
Connect this M/F twisted pair with outer shield cable to 34980A multifunction switch/measure mainframe and modules
-
product
Data Acquisition Mainframes
Flexible, modular Data Acquisition system with high performance scanning 6.5 digit DMM. 5 slot mainframes and modules for customized data acquisition solutions including temperature, resistance, current and voltage measurements
-
product
Mainframe Debugging and Analysis
Xpediter
Xpediter is Compuware's mainframe application interactive debugging and code coverage solution. When an application experiences a problem, developers need to get into an interactive test session to solve the issue. However, complex setup procedures make this a time-consuming step and delay the resolution process.Compuware's mainframe debugging and analysis tool Xpediter enables developers to get into an interactive test session with minimal effort and quickly move applications into production with greater confidence.
-
product
Switch Mainframe
SW1001
Switch between voltmeter and battery tester while testing. 66 channels max. (2-wire) to 18 channels max. (4-terminal pair). Circuit design friendly for impedance measurements that minimize errors between channels (Effect: 0.01% f.s.*). For BT4560 100 mΩ range, R measurements, and a measurement frequency of 1 kHz. For OCV measurement, internal resistance measurement, and external potential measurement of battery cells. Measure battery modules up to 60 V DC.
-
product
Pulsed SMU Systems
AMCAD Engineering has created professional, industry-proven pulsing technology for both pulsed-bias load pull (Pulsed Load Pull, PLP) and 50ohm transistor test applications. Systems come equipped with a mainframe controller which includes integrated power supplies and integrated input pulser with ±25V/200mA capability. The external output pulser module (probes, pulsers) is configured for 120V/30A pulsing.
-
product
Compact Tunable Laser Source with Continuous Sweep Mode, 1520nm to 1630nm
81940A
Keysight's 81940A high power compact tunable lasers enables optical device characterization at high power levels and measurement of nonlinear effects. It's improves the testing of all types of optical amplifiers and other active components as well as broadband passive optical components. As single slot plug-in modules for Keysight's 8163A/B, 8164A/B and 8166A/B mainframes, they are a flexible and cost effective stimulus for single channel and DWDM test applications. Each module covers a total wavelength range of 110 nm in the C+L-band.
-
product
Charge-Discharge Chassis For 208 VAC 3-phase
BT2203B
The BT2203B is part of the BT2200 Series cell formation and lifetime cycler solution. It is an 8-slot mainframe for 208 VAC 3-phase power.
-
product
Custom Configured MPS, 600W
N6711C
The Keysight N6711C is a 600 W build-to-order system that is shipped as a fully tested and assembled multiple-output power supply. Each N6711C consists of 1 N6701C mainframe and from 1 to 4 DC power modules. Modules are ordered as options to the N6711C.
-
product
PCI Express VXIbus Slot-0 Interface
ProDAQ 3030
The ProDAQ 3030 PCI Express VXIbus slot-0 interface is a C-size, register-based VXIbus module providing a direct connection from a PC to a VXIbus mainframe using the high-speed PCI Express serial bus. Together with any of the available host cards, the ProDAQ 3030 enables users to use a laptop, desktop, or server computer as an embedded controller. Optimized for low latency and high throughput, it provides a high-performance but cost-effective solution for a data acquisition system.
-
product
Data Acquisition System
DAQ973A
Get the next-generation data acquisition (DAQ) system with a three-slot mainframe and your choice of nine plug-in modules. Interface with the DAQ using Keysight BenchVue DAQ software or use the intuitive graphical front panel with task-oriented, self-guiding menus.
-
product
Modular System Power Supplies
N6700 Series
The N6705A is 4-slot mainframe that accepts 1 to 4 modules in any combination. Modules are ordered separately. Maximum output power is 600W. The DC Power Analyzer is designed for bench testing in R&D. It is a highly integrated instrument that combines up to four advanced DC power supplies, DMM, oscilloscope, arbitrary waveform generator and datalogger. It provides an easy-to-use interface, with all sourcing and measuring functions available from the front panel.
-
product
1800 Watt DC Electronic Load Mainframe
N3300A
The Keysight N3300A is a full-rack width mainframe with 6-slots that accepts combinations of N330x user-installable load modules (150 W to 600 W) for easy system configuration and future reconfiguration. The N3300A holds up to six N3302A, N3303A, N3304A, N3307A load modules, or three N3305A, N3306A double-wide modules, allowing a total up to 1,800 watts of maximum power.
-
product
90/120 GHz Dual Channel Optical Module
N1032B
The N1032B is a plug-in module for the DCA-X mainframe that includes two optical channels up to 120 GHz.
-
product
EasyEXPERT Group+ Software (for B150x Mainframe)
Keysight EasyEXPERT group+ GUI based characterization software is available for Keysight Precision Current-Voltage Analyzer Series. It is available on your PC or the B150xA's embedded Windows 7 platform with 15-inch touch screen to accelerate the characterization tasks. It supports efficient and repeatable device characterization in the entire characterization process from measurement setup and execution to analysis and data management either interactive manual operation or automation across a wafer in conjunction with a semiautomatic wafer prober. EasyEXPERT group+ makes it easy to perform complex device characterization immediately with the ready-to-use measurements (application tests) furnished, and allows you the option of storing test condition and measurement data automatically after each measurement in a unique built-in database (workspace), ensuring that valuable information is not lost and that measurements can be repeated at a later date. Keysight Precision Current-Voltage Analyzer Series provides the complete solution for device characterization with these versatile capabilities.
-
product
3-m, 78-pin Dsub Cable
Y1138A
Connect this M/F twisted pair with outer shield cable to 34980A multifunction switch/measure mainframe and modules
-
product
Electronic Load Mainframe GPIB
3300 Series
A 4 Channels 1200W Mainframe which accepts up to four Load Module.
-
product
Powered VXI Crates
VXI-C Size 6025
WIENER C-size VXI mainframes of the 6000 deliver highest performance and reliability. Incorporating high density & lowest noise power supply technology the 6000 VXI series is the best choice for any demanding test and measurement VXI application.
-
product
Microwave Transfer Switch Plug-In
1260-162AH/BH
The Astronics 1260-162AH/BH is a 2-slot microwave switch plug-in. It can be used in either the Astronics 1256 switching mainframe or the Astronics 1260-100 Adapt-a-Switch™ VXI carrier.
-
product
3-Slot Data Acquisition Mainframe With GPIB, Two 20-Channel Switch Modules, And One 20-Channel Multiplexer Module
DAQ973SB
The DAQ973SB Better Multiplexer Bundle offer includes a DAQ973A three-slot data acquisition mainframe, two 20-channel DAQM903A Actuator / GP switch modules, and one 20-channel DAQM901A multiplexer module. This bundle provides the following:3-slot mainframe with USB, LAN, and GPIB6.5-digit (22-bit) internal DMM60 channels of multiplexer switches6 channels of dedicated current measurements2- and 4-wire scanning300 V switching80 channels/s scanningbuilt-in thermocouple reference junction20-channel actuator / general-purpose switch with independent single-pole, double-throw (SPDT) relaysbuilt-in signal conditioning to measure thermocouples, RTDs and thermistors, AC / DC volts and current; resistance, frequency / period, diode test, and capacitance
-
product
Base Model Custom-Configured DC Power Analyzer, 600 W, Modular, 4 Slots
N6715C
The N6715C DC Power Analyzer is a build-to-order system that is shipped as a fully tested and assembled DC Power Analyzer. Each N6715C consists of one N6705C mainframe (described below) plus 1 to 4 DC Power Modules and up to 600 W total DC Power Module output power. To specify which modules you want installed in the N6715C, modules are ordered as options to the N6715C.
-
product
Mixed Signal Tester
STI9000
The STI9000 is a mixed signal ATE used for testing ASIC and MEMS products. Each STI9000 test instrument fits into a small tester mainframe and contains multi-functional analog and digital test resources.
-
product
Semiconductor Device Parameter Analyzer/Semiconductor Characterization System Mainframe
B1500A
Current-voltage (IV) measurement capabilities of spot, sweep, sampling and pulse measurement in the range of 0.1 fA - 1 A / 0.5 V - 200 VAC capacitance measurement in multi frequency from 1 kHz to 5 MHz and Quasi-Static Capacitance-Voltage (QS-CV) measurement capabilitiesAdvanced pulsed IV and ultra-fast IV measurement capability from minimum 5 ns sampling interval (200 MSa/s)Up to 40 V high voltage pulse forcing for non-volatile memory evaluation
-
product
MPOD Mini Crate
The Mpod mini crate is the small and low cost option for the WIENER multi-channel high and low voltage power supply system. The Mpod mini mainframe can house up to 4 plug-in low or high voltage modules. The integrated Mpod controller card provides10/100 Ethernet, CAN bus and USB-2 interfaces.
-
product
System Switch with High Performance DMM
3700A
The Model 3706A system switch with high performance DMM contains six slots for plug-in cards in a compact 2U high enclosure that easily accommodates the needs of medium to high channel count applications. When fully loaded, a mainframe can support up to 576 two-wire multiplexer channels for unrivaled density and economical per channel costs. The result is a tightly integrated switch and measurement solution that’s equally at home on the bench or in the rack.
-
product
Modular Power
RFP Chassis
AMETEK Programmable Power, Inc.
ReFlex Power™ is a high density, modular programmable power system providing DC, AC and electronic load assets all under control of a single controller. It provides a reconfigurable, flexible platform ideal for ATE and production test environments where RFP™ can provide programmable stimulus and bias power as well as programmable loads for the device(s) under test. The EIA 4U high RFP™ mainframe can hold up to 12 single-slot modules or combinations of single, dual and triple slot wide modules to configure (or reconfigure) the system for the particular requirements at hand. The mainframe can support up to 6 kW of output power.
-
product
Mainframe or -E Expansion Chassis - Preconfigured Single or Two Pole Matrix Systems
LXB/128-MF
These Chassis are preconfigured single or two pole matix systems. A single chassis can be a 16x8 matrix, two 16x4 matrices, a single 32x4 or a single 64x2 configuration. Chassis is modular so you may start with a smaller size and increase the configuration as your needs grow.
-
product
Modular DC Power Supply
62000B series
Chroma's new 62000B series of Modular DC Power Supplies offer many unique features for Burn-in and plating/electrolysis applications. The features include a N+1 redundancy, high power densities, hot-swappable maintenance, remote ON/OFF and programmable control via the CAN bus. The 62000B family offers 5 types of power module with ranging from 1V to 150V, current from 10A to 90A, and offers two mainframe type of six and three position. The six position mainframe can envelop in up to six power modules paralleled operation for 9KW power output. The 62000B can easily parallel up to fourteen mainframe to 120KW with current sharing and CAN bus control for bulk power applications. The Modular DC Power Supplies of 62000B are very cost effective with high power density and low current ripple. These instruments have be designed for burn-in applications such as the LCD panels, DC-DC converters, power inverters, notebook computers, battery chargers and many other types of electronic devices.
-
product
Power Supply Mainframe And Modules Instrumentation
High power, dual channel PXI User Power Supplies as well as precision DC source instrumentation. These products are offered in both PXI and GTXI formats.
-
product
6U Power Supply Mainframe
GX7400A
The GX7400A is a dual output programmable DC power supply designed for use in 6U PXI systems. The GX7400A occupies three slots and is controlled via the PXI bus. The AC power is provided using a panel-mounted receptacle. The power supplies are fully isolated and can be externally connected in series to provide higher voltage.
-
product
Digital Channel, 10 MΩ Input, ±25 V, 8 Channel
CX1152A
The CX1152A Digital Channel provides 8-channel digital trigger for the CX3300 Device Current Analyzer series, which is useful when a low power device with digital I/Os is evaluated. Only the CX3324A mainframe has the interface of this product. The input impedance of each channel is 10 MΩ in order to minimize the load current from the digital channel.
