Filter Results By:
Products
Applications
Manufacturers
Noise
a signal's fluctuation other than that desired.
See Also: Pink Noise, White Noise, RF Noise, Distortion, NVH
-
product
Noise and Vibration Tester
SKF Condition Monitoring Center
High tech analysis and measurement such as frequency analysis (FFT) and further advanced analysis pinpoints faults. Spectral masks help to optimize the bearing performance in the particular customer application.
-
product
Impulse Noise Simulators
INS Series
A simulator to reproduce fast rise-up noises which are generated when switching ON / OFF electric current on the inductive load. It can be used for performance evaluation of electronic equipment upon reproduction of line noises which are intruded to the power supply lines or induced noises onto the telecommunication lines.
-
product
Noise Figure Analyzer, Multi-touch, 10 MHz to 7 GHz
N8974B
The N8974B high performance noise figure analyzer is designed to make fast, accurate and repeatable noise figure measurements. When paired with an SNS Series noise source and U7227 Series USB preamplifier the ENR data from the SNS and USB preamplifier data automatically downloads into the N8974B.
-
product
Measurement Hardware
Whether it’s in a vehicle, on a test stand or monitoring equipment and machinery - imc data acquisition systems are easy to operate and will help you become more productive and profitable. Our products are suited for work in mechanical and mechatronic applications. They handle up to 100 kHz per channel, are compatible with almost all signal sources and sensors, and can measure nearly all physical quantities such as pressure, force, speed, vibration, noise, temperature, voltage and current. The spectrum of imc data acquisition systems ranges from simple data acquisition via integrated real-time calculations, to the integration of models and complete automation of test stands.
-
product
Multi Output Regulated DC Power Supply
LQ6324T
- Low cost general purpose laboratory bench unit.- Fully protected against overload and short circuit.- Three independent outputs electrically isolated from each other.- 5V/5A with over voltage crowbar protection for digital ICs.- Electrically floating outputs up to 500V DC w.r.t. ground.- Compact modular construction.- Precise regulation, low ripple and noise for both constant voltage and constant current operation.- Quality components and conservating ratings for high reliability and long life.
-
product
L-Band Separate Raman Fiber Amplifier
RFA6000
Hangzhou Huatai Optic Tech. Co., Ltd.
1. Erbium-doped Fiber Amplifier, due to the multiple cascades and the accumulation of noise caused by spontaneous emission, will reduce the system CNR greatly and thus it will limit the transmission capacity and distance of the system. Raman Fiber Amplifier (RFA) is a newly designed fiber amplifier based on Stimulated Raman Scattering (SRS) effect. It is considered as the core technology of new generation DWDM fiber over-long communication. Compared with Erbium-Doped Fiber Amplifier, Raman amplifier has the advantage of low Noise Figure (NF), wider gain bandwidth, flexible gain spectral region and stable temperature. It is the only device that can operate in 1300~1600 nm.
-
product
Preselectors and Switch Filter Banks
Our preselectors and switch filter banks offer low noise figure, high dynamic range, state-of-the-art filter rejection with high channel-to-channel isolation front ends, realized in compact building blocks, designed in custom form factors. Applicable markets include: EW, missiles, radar, communications and space.
-
product
Oscilloscope, 200 MHz, 2 GS/s interleaved, 4 CH, 200 Mpts/Ch DSO, Fully Loaded with 10.1" Color Display
T3DSO2204HD
The T3DSO2000HD series of Bench Oscilloscopes feature 4-channel models with analog bandwidth options of 100 MHz, 200MHz and 350 MHz. The T3DSO2000HD Oscilloscopes use 12-bit high resolution ADCs and a low noise front end which provides an impressive noise performance to cover a wide range of measurement applications. Each model offers a maximum sample rate of 2 GSa/s (interleaved) and a maximum memory depth of 200 Mpts in interleave mode. The MS configured models also include a 16 channel logic probe as standard.
-
product
XCITE 1300T Torsional Series
The Xcite 1300T Torsional Series of modal exciters provides pure torque input into structures for modal parameter estimation without the bending mode coupling effects present when linear excitation is applied through moment arms. These systems are used in structure borne noise tests of structures such as automotive and truck transmissions, prop shafts, axles, differentials, and torsional engine dampers.
-
product
Power Rail Probes
Optimized for power integrity measurements, these probes combine low noise contribution, DC offset up to 60 V, high bandwidth, low loading, and a wide range of connectivity alternatives.
-
product
Sound Level Meter
ST-8850
Standard Instruments Co., LTD.
This digital meter is ideal for general sound level measurements. The device features analog AC/DC outputs for connecting to an analyzer or recorder. Coming with a wide range of 30dB to 130dB, this sound level meter is great for measuring noise in factories and checking acoustics in auditoriums. 1.5dB accuracy. Meets IEC651 type 2 standard. Max. hold and data-hold functions. Built-in calibration check.
-
product
Signal Generator
8006
Normal switching mode, SSB phase noise will be degraded in the fast mode. 5 digit BCD, 1 latch control line, 25 pin female, D type connector
-
product
Test Solutions
AT/CX/CM Series
The VeEX AT/CX/CM series are next generation test solutions designed for analog and digital cable TV networks supporting VoIP, WiFi, and Internet service. Analog and Digital SLM, ingress noise sweep, deep interleave support, and QAM constellation analysis are among many standard features. Enhanced optional features include QAM16/64/128 Upstream Generation (USG), Reverse Path QAM Analysis, and DOCSIS 2.0/DOCSIS 3.0 Cable Modem emulation. A high capacity LiIon battery pack provides extended autonomy for a full day use with only a single charge.
-
product
Noise Measurement Kits
Our noise measurement kits contain all the accessories you need to take accurate noise measurement instruments correctly.
-
product
Profiling Belt Radiometer
ILT400
International Light Technologies
The IL400 Profiling Belt Radiometer continues with the all-in-one exposure, intensity, and profiling capability first introduced in the IL393. New solid-state detector and ultra-stable amplifier technology along with rechargability combine to give lower noise, greater speed, and higher accuracy at a price below any precision belt radiometer sold today.
-
product
Rubidium Oscillators
Precision Test supplies a full range of rubidium oscillators and modules, including ultra low phase noise and ultra low Alan deviation modules.
-
product
Calibrated, Integral Isolator Noise Sources
Calibrated, Integral Isolator Noise Sources by Pasternack
-
product
Two Channel Phase and Amplitude Noise Analyzer
DCNTS -190
The DCNTS is a two channel Phase and Amplitude noise analyzer. Its dual demodulator architecture allows the system to use cross-correlation to cancel its internal noise and limitation; it is like comparing the outputs of 2 systems and only display the similarities while rejecting differences. Its main extension is the Residual Noise measurement front-end which includes all necessary hardware to automatically measure residual noise on 2-ports devices either in RF frequencies or microwave. It could be a frequency multiplier or divider, an amplifier or any other phase coherent input to output device.
-
product
Sindie Online
Sindie Online is an industrial-grade process analyzer delivering continuous sulfur detection to monitor fuel streams and help to prevent tank contamination. It has many advantages over competing technologies: Powered by MWDXRF, Sindie Online has an exceptional signal-to-noise ratio using monochromatic excitation of the X-ray source characteristic line – a technique that is faster, safer and cleaner than UVF.
-
product
Class 2 Integrating Sound Level Meter
Castle Sonus GA216I
The Castle Sonus GA216i is a feature packed instrument, fully compliant with IEC 61672:2002 Class 2. This meter gives simultaneous Leq and peak measurements for assessments to the Control of Noise at Work Regulations 2005. It has a high-specification measurement microphone and is cased in tough, crack resistant ABS plastic. To comply with the Control of Noise at Work Regulations 2005, this Class 2 Sound Level Meter enables you to assess Noise in the workplace at fantastic value.
-
product
Sound Level Meters & Decibel Meters
Find high performance easy to use Class 1 or Class 2 sound level meters. Ideal professional-grade noise meters for accurate and compliant noise measurement for every application including occupational noise and environmental noise.
-
product
Femtosecond Fiber Lasers
Best in class femtosecond fiber lasers: highest output power, lowest phase noise, highest reliability. Choose the perfect model for your application from our Erbium and Ytterbium fiber lasers with center emission wavelengths from the visible to the NIR, and extending to the Mid-IR in selected models.
-
product
Cigarette Lighter Socket Sensor
FT-0801
The FT-0801 cigarette lighter socket sensor detects ignition noise of voltage from cigarette lighter socket sensor as rotation signal. Useful for signal detection from a cigarette lighter socket equipped in an automobile or construction machinery.Rotation signal can be detected from a cigarette lighter socket by using the FT-0801 even if it is difficult to attach a rotation detector inside of an engine room.
-
product
28/45 GHz Quad Optical Channel DCA-M
N1092D
High accuracy, low cost solution for optical waveform analysis including solutions for 8.4 through 64 GBaud, very low noise and jitter, and fast sampling rates for high throughput.
-
product
Noise Source, 10 MHz to 18 GHz, nominal ENR 6 dB
346A
The Keysight 346A noise source is the ideal companion to Keysight's noise figure solutions. Since it is broadband (10 MHz to 18 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty; reflections of test signals. The very small change in reflection coefficient (<0.01) from ON to OFF is designed especially for accurate characterization of input-impedance-sensitive devices (like GaAsFETs and many UHF amplifiers).
-
product
Platform
ATX7006A
The ATX7006A is a fully integrated solution for testing ADCs, DACs and other Analog functions. It combines very high accuracy, low noise and fast sampling with an exceptional ease of use. Traditionally data converters are tested using a whole stack of bench instruments, filters, switch matrices and user made software. Many engineering hours are needed to get reliable results. The ATX7006A is a single instrument for all your data converter testing and test methods.
-
product
Microwave Noise Source Generators
Noise Sources supply white gaussian electronic noise. The output is a flat instantaneous broadband electronic random noise. The noise source converts a DC input to noise. Units are available in bands between 10MHz thru 26.5 Ghz.
-
product
Hand-held VNIR Spectroradiometer
HandHeld 2™
Analytical Spectral Devices, Inc.
The HandHeld 2 provides the ideal combination of performance, portability, and durability. The HandHeld 2 spectroradiometer employs a high-sensitivity detector array, a low stray light grating, a built-in shutter, DriftLock dark current compensation, and second-order filtering to produce a high signal-to-noise spectrum in under a second.
-
product
(125×150×30.5mm) High Power Multi-ports Output CATV FTTP EYDFA Module
EATV5400x-FM05
Hangzhou Huatai Optic Tech. Co., Ltd.
Huatai EATV5400 series is a low noise, high performance, high power multi-ports EYDFA module, which is specially designed for CATV system. It offers a flexible and low-cost FTTP solution for CATV large area coverage of metropolises and medium-sized cities.
-
product
Mobile Cable Fault Location System
BAUR Syscompact 4000
BAUR Prüf- und Messtechnik GmbH
Fault location with Syscompact 4000. The Syscompact 4000 is a compact, fully enclosed fault location system for pre-location and pinpointing of high-resistive, low-resistive and intermittent faults on low- and medium-voltage cables. Easy operation and the use of latest fault location methods enable fast and safe fault location.* Location of low-resistive, high-resistive and intermittent cable faults* Efficient cable fault pre-location methods* Pinpointing according to the noise location method or acoustic propagation time measurement* (with Universal Locator and ground microphone)* Sheath fault location according to the step voltage method (with Universal Locator and two measurement probes)* Easy to handle
