Filter Results By:
Products
Applications
Manufacturers
PHY
Tests hardware, electrical and procedural interface to the transmission medium.
-
product
CPE Design Verification System
Jupiter 310
Jupiter is the industry standard for automated DOCSIS physical (PHY) layer testing. It provides the most comprehensive test coverage and accurate results on the market for DOCSIS 3.1 devices.
-
product
Arasan PHY IP
Arasan PHY’s are readily available and in production with multiple foundries from 16nm to 180nm. Our PHY’s are designed for low power on the most advanced nodes for the mobile market while also targeting the automobile market on specialized nodes where extreme temperature tolerance is required.
-
product
Ethernet Transformers
Pulse’s Ethernet transformers are RoHS compliant and qualified at major PHY suppliers. 100/1000/2.5G/5G/10GBASE-T Ethernet transformer modules are optimized for all major LAN transceivers. All modules provide electrical circuit isolation that meets IEEE 802.3, while maintaining signal integrity needed for the most demanding applications.
-
product
HDMI Phy and Protocol Aux Channel Analyzer Module
The Teledyne LeCroy quantumdata 980 HDMI Phy & Protocol Aux Channel Analyzer module supports compliance testing of the HDMI DDC bus and HDMI 2.0 CEC testing (partial support only). The module’s CEC compliance tests enable you to identify compliance failures early in the development cycle. The solution is ideal for pre-testing and self-testing (where permitted) your HDMI 2.0 device. The module also supports compliance testing of the HDMI DDC bus voltage and timing parameters in accordance with HDMI 1.4b. Future releases of the module will support functional tests and compliance tests on other HDMI auxiliary channels.
-
product
Industrial Ethernet Physical Layer Devices
The ADI Chronous™ Industrial Ethernet physical layer (PHYs) portfolio includes solutions for standard 10 Mbps, 100 Mbps, and 1 Gbps. It also features the new 10BASE-T1L technology for single-pair Ethernet.Our industry-leading low latency and low power PHY technology maximizes data transmission and signal integrity in deterministic applications by reducing cycle times and system power consumption. It enables superior synchronization of signals across the industrial network and supports the development of TSN.
-
product
PhyView Analyzer
PVA-3000
Connects up to 24 10/100/1000Base-T ports and provides access to the PHY Performance Test Suite supporting one-click, fully automated transmitter, receiver, and, auto-neg testing.
-
product
ARINC PCI Express One Lane Interface Card
PCIE1L-A429
The ARINC PCIE1L-A429 Interface Card and AltaAPI Support Software Represent the Latest ARINC 32-bit FPGA Protocol Engine Technology. Encode and Decode almost Any ARINC-429 PHY Level Label/Word Signal. The First Card in the Industry to Offer Advanced Test Functions of Signal Generation and A/D Signal Capture. The one lane card PCIe is the industry first low profile
-
product
PHY Performance Test Suite
The innovative PHY Performance Test Suite provides comprehensive 10/100/1000Base-T Ethernet interface verification with unique plug’n play automation.
-
product
Ethernet POE & PHY Testing
Networked Communication Solutions, LLC
A multi-port programmable load.
-
product
Multibus Ethernet Card
MS 1750
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz- SDRAM Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Multibus Interface- Serial Interfaces: Up to four external UARTs- CAN 2.0B controller- Three I2C ports- Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements
-
-
product
Efficient And Effective Physical Layer (PHY) Testing Of 10/100/1000Base-T Interfaces
Explore Sifos Technologies’ highly unique, plug’n play 10/100/1000Base-T Ethernet Physical Layer Testing Solutions. Cost Effective and Comprehensive PHY Testing without Scopes, Fixtures, Probes, and Test Signals.
-
product
Digital Services
*Processor verification experience*Memory verification*Bus protocols and DMA verification*Expert in high speed controller verification*Physical layer (PHY) verification
-
product
USB Power Delivery and Type-C™ Tester & Analyzer
GRL-USB-PD-C2 (GRL-C2)
GRL-USB-PD-C2 (GRL-C2) is the only solution available that supports all compliance test specifications for USB Power Delivery 3.0 and USB Type-C Alternate Mode designs, and enables product developers to quickly run full compliance and validation test suites at the push of a button. GRL-C2 provides an automated, efficient, and fully-integrated way perform all required USB Power Delivery version 3.0 and 2.0 and related tests over the USB Type-C connector, as well as PHY test automation for USB Type-C Alternate Modes. GRL-C2 automates all required USB PD compliance tests for power providers (chargers), consumers, dual-role ports, and cable and adapter E-Markers; and is the only solution available that integrates Qualcomm Quick Charge 4+ and Intel Thunderbolt-specific test items. GRL-C2 also incorporates analyzer capability to sniff PD traffic. GRL-C2 integrates all required USB PD tests into a single 2-port tester, including all tests supported on GRL’s USB-IF approved first generation solution introduced in 2015. Each port can be configured independently as a PD Provider or Consumer. All other PD Protocol and Power tests are fully integrated, removing the need for external electronic loads.
-
product
Embedded Vision And Processing FPGA
CrossLink-NX
*Instant-on configuration – IO configures in 3 ms, and device as fast as 8 ms*Two hardened 4-lane MIPI D-PHY transceivers at 10 Gbps per PHY / 2.5 Gbps per lane*Up to 37 programmable source synchronous I/O pairs for camera and display interfacing
-
product
C/D-PHY CSI-2/DSI Analyzer
Envision X84
is the first combination C-PHY/D-PHY analyzer in single platform. The Envision X84 supports C-PHY/D-PHY and Cameral Serial Interface (CSI-2) and Display Serial Interface (DSI/DSI-2) on a single hardware platform. Envision X84 supports C-PHY version 1.1 and D-PHY 2.1 as well as CSI-2 version 2.1 and DSI version 1.3 and DSI-2 version 1.1. The Envision X84 offers Silicon ad device designers, integrators and validation engineers a complete, robust yet flexible tool to ensure the correct and efficient operation of Camera and Display over C-PHY and D-PHY implementations.
-
product
RF PHY Tester
TLF3000
TLF3000 RF PHY tester is a wideband, ultra-high dynamic range 2.4 GHz software-defined receiver, signal analyzer and signal generator. It captures and analyses the entire 2402-2480 MHz band simultaneously providing RF PHY testing, signal generation, signal analysis in one powerful package.
-
product
Low Power FPGA Featuring Hardened MIPI D-PHY, LVDS, SLVS, SubLVDS, & Open LDI Bridging
CrossLink
*Two 4-lane MIPI D-PHY transceivers at 6 Gbps per PHY*15 programmable source synchronous I/O pairs for camera and display interfacing*Available in amazingly small 2.46 mm x 2.46 mm WLCSP packages and BGA packages with 0.4 mm, 0.5 mm and 0.65 mm pitch
-
product
PCI Card
EXC-1394PCI
The EXC-1394PCI card for the PCI bus is an intelligent test and simulation card for interfacing to an IEEE-1394 data bus. It implements a 1394b PHY layer, operating at 100, 200, or 400 Mbps.
-
product
Ethernet MACsec PHY
Macom Technology Solutions Holdings Inc.
IEEE 802.1AE Media Access Control Security (MACsec) is an industry standard security technology that provides secure communication for Ethernet traffic. MACOM’s wire-speed Ethernet MACsec PHY products offer highly scalable and cost-effective encryption solutions to address the data security issues in wireless, carrier, data center and cloud networks. Combining MACOM’s strength in high speed, high performance mixed-signal I/O and industry leading CMOS silicon technology, MACOM’s MACsec PHY products provide line-rate encryption and authentication at a very low power-footprint that enables encryption at wire-speed on every port. They are ideal for adoption on switch/router line cards, data center interconnect (DCI) transponder and wireless xHaul aggregation systems to provide security function in addition to the connectivity to optical and copper modules.
-
product
Training Board
The JT 2156 training board has been devised to demonstrate all the latest features and test techniques available to users of JTAG Technologies’ ProVision & JTAG Live application development systems. As well as a modern ARM Core processor, the design also includes an Altera Cyclone FPGA, DDR Memory, Ethernet PHY, and several SPI and I2C peripheral parts. The JT2156 is shipped with a comprehensive self-study manual for getting to know the in-depth features of ProVision and/or JTAGLive Studio. For Altium users the design also serves as an example of how to adapt the Nano board into a realistic custom design.
-
product
1394 and AS5643 IP Core Solutions
Synthesizable 1394 and AS5643 IP Core solutions PHY, LLLC, PHY & LLC for multiple FPGA families.
-
product
MIPI M-PHY Protocol Analyzer
U4431U
Power to meet the needs of today’s and tomorrow’s designs Up to Gear 3 HS data rates Up to 16 GB trace depth Up to 4 data lanes Complete insight into complex designs Track multiple M-PHY busses from the PHY to the application layer Raw Mode 8b/10b data views Infiniium Oscilloscope integration Powerful interface that allows unlimited customization of system views
-
product
System on Module Microsemi PolarFire
SoM3-MPF300T
Sundance Multiprocessor Technology Ltd.
The SoM3-MPF300T is a small footprint System On Module (SoM) with 40x50mm dimensions. It has a low power, highly secure FPGA from the PolarFire family from Microsemi. It comes with 4GB of DDR4 memory, Ethernet PHY, and FLASH. This SoM is ideal for being used in complex hardware designs, and is compatible with Sundance SoM carriers SE215 and EMC2-DP-V2.
-
product
Training Board
JT 2156
The JT 2156 training board has been devised to demonstrate all the latest features and test techniques available to users of JTAG Technologies’ ProVision & JTAG Live application development systems. As well as a modern ARM Core processor, the design also includes an Altera Cyclone FPGA, DDR Memory, Ethernet PHY, and several SPI and I2C peripheral parts. The JT2156 is shipped with a comprehensive self-study manual for getting to know the in-depth features of ProVision and/or JTAGLive Studio. For Altium users the design also serves as an example of how to adapt the Nano board into a realistic custom design.
-
product
Wireless Test Solutions for Bluetooth®, Wi-Fi, Matter/Thread/Zigbee
Teledyne LeCroy's Frontline family of wireless protocol analyzers, sniffers, and testers deliver unparalleled performance for complex multi-technology test environments including market-leading support for the latest Bluetooth, Wi-Fi (802.11), and Matter/Thread/Zigbee (802.15.4) technologies. We've got you covered - from RF PHY testing to protocol analysis to Bluetooth LE conformance testing.
-
product
Ethernet PHY
Macom Technology Solutions Holdings Inc.
MACOM’s portfolio of 10G/25G/40G/50G/100G Ethernet Physical Layer (PHY) devices offer unparalleled performance while maintaining high density at low cost. Integrated high-speed, high performance mixed signal I/O using advanced CMOS process nodes support a variety of optical and copper connectivity interfaces allowing the Ethernet PHY product line to span rack and cluster connectivity within the data center, wireless fronthaul, midhual and backhaul connectivity for 5G wireless infrastructure, and seamlessly extend to core networks over DWDM optical links. Advanced features such as in-service eye monitors, traffic monitoring, optical module identification and link training are just a few of the advantages that MACOM’s portfolio provides for end users to leverage for faster bring up, higher reliability and smarter networks.
-
product
ARM 9 System on Module
MS 1515
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz SDRAM- Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Serial Interfaces: Up to four external UARTs- + CAN 2.0B controller- + Three I2C ports- + Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements- Mechanical: 60 mm wide x 60 mm long x 5.4 mm high
-
product
1000BASE-T1 MEDIACONVERTER EMC
Art.-Nr.: TE-1404-1
The ideal solution for working quickly and efficiently with 1000BASE-T1 EMC measurements The 1000BASE-T1 MediaConverter EMC is especially designed for measurements within the EMC chamber. It is delivered in a Set with an adapter board which enables internal PHY status readings and provides one point-to-point connection between Automotive Gigabit Ethernet and SFP Gigabit Ethernet, with which optical fibre modules are used.
-
product
Digital Optical Transport
The ATX GigaWave digital optical transport portfolio is designed to fortify cable operators with maximum flexibility and cost efficiencies to support a range of applications and business models. The GigaWave Digital Link Extender (DLX) is optimized to support distributed access architectures (DAA), including Remote PHY (R-PHY) and Remote MACPHY (R-MACPHY), as well as Passive Optical Network (PON), Small Cell/5G and enterprise business services. The GigaWave Digital Link Amplifier-HUB (DLA-HUB) is a field-hardened, gain-flattened EDFA platform that enables the elimination of physical hub sites along long-reach optical routes. The GigaWave digital optical transport portfolio also enables MSOs to leverage the advantages of digital optics over analog, including the capability to transport signals over longer distances and provision additional wavelengths per fiber.
