Filter Results By:
Products
Applications
Manufacturers
Seismic Accelerometers
sense ground vibration.
See Also: Seismic, Seismometers, Seismic Arrays, Earthquake
-
product
High Sensitivity Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
The piezoelectric accelerometers on this page are intended for the measurement of lowest vibrations. Typical fields of application include the monitoring of buildings, dams, bridges, oil platforms and pipelines. These sensors are often called seismic accelerometers because they are used to monitor construction activity, volcanoes and earthquakes. Their high sensitivity is achieved -unlike other high sensitivity accelerometers- by the sensing element itself and not by internal amplification. From this results highest resolution and lowest noise.
-
product
Triaxal Seismograph
BC 1313 TRIAXIAL SEISMOGRAPH
BC 1313 seismographs are seismic accelerometers, the parameter measured – vibration acceleration. For BC 1313 seismic transducers, the system is provided for sensing element electrical stimulation using an actuator to determine conversion ratio true value during periodic recalibration without dismantling. Power check system is also allowed for in BC 1313 seismographs.
-
product
Accelerometers
The unit is based on micro machined MEMS technology. The unit contains a 35g sensing element. The element is scaled to optimise the resolution to suit the g range of interest. An internal amplifier provides an output between 0 and 5 volts. The on board microcontroller and temperature sensor are used for offset drift compensation. This unit can be re-calibrated at the factory.
-
product
Accelerometers
352C33
Sensitivity (10 %) 100 mV/g10.2 mV/(m/s) Measurement Range:50 g pk 490 m/s pk Frequency Range (5 %)0.5 to 10000 Hz0.5 to 10000 Hz Frequency Range (10 %)0.3 to 15000 Hz0.3 to 15000 Hz Resonant Frequency:50 kHz50 kHz Broadband Resolution(1)0.00015 grms0.0015 m/s rmsNon-Linearity:1 %1 % Transverse Sensitivity:5 %5 %.
-
product
Accelerometers
Dytran accelerometers are used for product testing & development, structural monitoring, and industrial machinery health monitoring management. We offer a wide range of piezoelectric & VC MEMS sensors.
-
product
Accelerometers
Monitran General Purpose Analysis Sensors are ideal for use with portable and on-line vibration analysers, providing the user with a complete spectrum of vibration intensity against frequency. Changes in this spectrum allow the user to determine the health of the machinery to which the sensor is attached. Most analysers will store the spectral values and monitor changes over a period of time, allowing prediction of expected component life and enabling efficient planning of maintenance schedules.
-
product
Accelerometers
Velocity sensors and several types of accelerometers made to industrail standards for measuring vibration in a variety of applications and detecting potential machine failures before they occur.
-
product
Linear Accelerometers
Columbia Research Laboratories
Columbia Research Labs line of Force Balance Linear Accelerometers offers low cost, high performance, general purpose single axis accelerometers that are ideal for DC and low frequency measurements, with both voltage and current signal outputs available. Also offered are Columbia's Solid State Sensors and our specialized Airborne Sensors that generate outputs specifically designed to operate from +24 to +32VDC aircraft power, that is excellent for airborne telemetry applications. And our Low Noise Sensors are designed for use in seismic, low level, low frequency motion studies.
-
product
Accelerometers
Columbia Research Laboratories
The force balance accelerometer has a classical critically-damped, second-order frequency response. There is no peaking in the response but simply a smooth roll-off above the natural frequency. This property along with the excellent characteristics of the "HP" torquer design makes Columbia accelerometers the best choice for demanding applications where precise DC and near-DC measurements are needed in demanding shock and wide band vibration environments. Columbia force balance accelerometers are available to cover virtually all applications. Low noise, high output units can be used for seismic structure motion studies while miniature, high range versions are optimum for measuring more violent high G environments encountered in many industrial, aircraft and missile applications.
-
product
Accelerometer Simulator
MTN/8302
The MTN/8302 is a battery-powered unit designed to simulate a constant current type accelerometer. It enables test and calibration of vibration monitoring equipment such as the Monitran MTN/6000 series.
-
product
Accelerometer
EMIC offers many kinds of accelerometers available for various vibration measurements. They are a ultra small light weight accelerometer for highly precise measurement, a special tri-axial accelerometer for simultaneously measuring a vibration in three orthogonal axes, a large output accelerometer for measuring an earthquake and a suitable accelerometer for measuring and analyzing a building structure.
-
product
Accelerometers
Accelerometers measure linear acceleration. They can be also used for specific purposes such as inclination and vibration measurement. MEMS accelerometers embed several useful features for motion and acceleration detection, including free-fall, wakeup, single/double-tap recognition, activity/inactivity detection and 6D/4D orientation.
-
product
Pioneer Seismic Cabinet
The Pioneer rack is the cornerstone of our broadcast cabinet line, offering flexibility and strength. With a weight capacity of 2,000 lbs., Pioneer’s heavy-duty frame is designed with cross braces interlocked and welded into the corner post.
-
product
Advanced Seismic Source
GI-SOURCE
Sercel developed the GI-SOURCE to reduce and suppress the bubble oscillation from a single impulsive source to simplify processing. The GI-SOURCE impulsive source is based on the same technology as the GI-SOURCE but is different in that it has two independent air chambers within the same casing : the Generator (generating the primary pulse and creating the main bubble) and the Injector (injecting air inside the main bubble so that it collapses quickly).
-
product
Special Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
This page shows vibration sensors for special applications.The Seat Pad Accelerometer Model KS963B100-S was developed for measuring whole body vibration transmitted by driver seats of building machines and other vehicles in compliance with ISO 10326-1 and ISO 7096. The sensor has an IEPE output for robust signal transmission.
-
product
Miniature Triaxial Accelerometers
Miniature triaxial accelerometers are available in a variety of sensitivities to suit specific application requirements. These small and lightweight units have a high frequency response and minimize mass loading on test structures. They are ideal for installation in space restricted locations
-
product
Universal Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
There are models with charge output and with IEPE compatible voltage output. The transducers of KS series have a shear type sensing element making them less susceptible to thermal transients and base strain. The accelerometers of KD series have a compression type sensing element combining rugged design, precision and low cost.
-
product
Three Axis Accelerometers
TAA
The Inertial Labs MEMS TAA-308, TAA-315 and TAA-340 are the third generation of the Inertial Labs MEMS, three-axis high-precision accelerometers released in a stand-alone design. The TAA-308, TAA-315 and TAA-340 are revolutionary, compact, self-contained, strapdown, Navigation-grade Accelerometers that measure linear accelerations with high precision due to their unique design and developed by Inertial Labs over last 20 years several significant know-know and technics in calibrations of inertial sensors. Measured by TAA Accelerometers accelerations are determined with low noise and very good repeatability for both motionless and dynamic applications.
-
product
Digital Accelerometer
ZET 7052-N
Digital accelerometer ZET 7052-N is equipped with a compact sensing element and is designed for linear acceleration and vibration acceleration variable constituent measurement via three mutually perpendicular planes. Small weight of sensing element (1,5 g) considerably reduces self-mass load and compact dimensions (8,5×8,5×8,5 mm) enable use of the digital accelerometer ZET 7052-N for vibration measurements in systems with small active area.
-
product
Accelerometers & Angle Sensors
Accelerometers & Angle SensorsSingle axis, triaxial accelerometers and impulse hammers for vibration measurement and structural modal analysis.Angle sensors are perfect complementary sensors for applications like order tracking.
-
product
Seismic interpretation Software
Intersism
Intersism it's a software designed to make the entire processing of seismic data coming from a refraction seismic method acquisition. The software extract data directly from the file SEG2 format, SEGY or SU - and give you the possibility to put directly the first arrival picking time.
-
product
General Purpose Piezoelectric Accelerometers
Piezoelectric accelerometers offer tremendous versatility for shock and vibration measurements. These rugged sensors can withstand adverse environmental conditions. A wide variety of configurations are available to support multiple application requirements. Specialty units are also available through mechanical or electrical design modifications or additional qualification testing.
-
product
Piezo-resistive Accelerometer
A Piezo-resistive Accelerometer has a stable structure composed on a silicon chip created by the micromachining and semiconductor production technology. A mass and a beam on which a set of the Piezo-resisters are created on the silicon chip. A set of electrical bridged is formed by such Piezo-resistive resisters to generate signals proportional to the applied acceleration.
-
product
GEOPHYSICS, SEISMIC, and ATMOSPHERICS RESEARCH RECEIVER
Type RAS-1
Called the RAS-1, the receiver is designed for ultra low and very low frequency scientific research work, including the exploration of low frequency emissions due to seismic and earth-quake activity, study of atmospheric phenomenon such as "whistlers", and low frequency Sudden Ionospheric Disturbance (SID) and electromagnetics phenomenon. The RAS-1 will receive signals from under 200 Hz. To over 250 KHz in both narrow bandwidth modes as well as broad badnwidth reception.
-
product
Accelerometers
Honeywell Industrial Automation
Honeywell Sensotec Accelerometers are manufactured as standard, modified standard, and custom to provide the fastest possible delivery. Many units can be shipped from our extensive accelerometer stocking program within 24 hours. We offer a wide range of frequencies from DC to 6000 Hz and full ranges of 5 G to 2000 G. These units will survive overloads up to 500% (varies with model) and are also designed to cope with operating temperature between 100 and 500 degrees Fahrenheit.
-
product
Miniature Single Axis Accelerometers
Miniature piezoelectric accelerometers are required for applications demanding high frequency range, small size, and low weight. Product testing is necessary in today’s competitive marketplace in order to optimize designs, reduce defects, and improve customer acceptance and satisfaction. Shock and vibration testing offers a structured approach for verifying survivability in environmental influences that may be encountered during service and for precipitating incipient failures so they are not encountered by the end-user. PCB® accelerometers are used extensively for monitoring an object’s response to a programmed vibration input and for controlling the vibration profiles during testing.
-
product
Compact Accelerometer (Shock Meter)
AP2019
*Can be used as shock sensors in equipment diagnostic systems;*Combination of high axial sensibility, intrinsic frequency and shock resistance;*Low sensitivity to electromagnetic fields;*Low intrinsic noise level.
-
product
Dual Accelerometer
M6
*Built-in damping and overrange stops*Safe overrange limits*Force up to 2000 G without damage to sensor*Temperature compensated for accurate response over entire temperature range*High slew rate operational amplifiers (1.2 V/usec)*Internal RF shielding on each pin
-
product
High Temperature Accelerometer
HA602-A100
Charge Amplifier for use with CM362 High Temperature Accelerometers, Acceleration
-
product
Triaxial Accelerometers
Metra Mess- und Frequenztechnik in Radebeul e.K.
Triaxial accelerometers are intended for simultaneous measurement of vibration in 3 perpendicular axis. All models have a central drilling for easy screw attachment and convenient axis alignment.
