Filter Results By:
Products
Applications
Manufacturers
- Applied Instruments, Inc.
product
Forward Path NPRT 2200 Noise Power Ratio Test Set
NPRT 2200-F
The NPRT 2200 measures the NPR of a device across a range of power levels. This test quantifies intermodulation distortion and determines the dynamic range of optical transmitters, amplifiers and other active HFC network devices. The included PC software uses predefined test setups to run a "Power Sweep" series of NPR measurements and graph the results.
-
product
Erichsen Metal Sheet Testing Machine for FLC, FLD
GBW-600
Jinan Testing Equipment IE Corporation
GBW series Erichsen Metal Sheet Testing Machine is designed on the basis of screw universal material testing machine, using the servo motor for highly accurate loading for punching, meanwhile, it is equipped with hydraulic servo control system for pre-tightening/clamping of metal sheet. It is ideal to evaluate the plastic deformation performance and ductility of metal sheet & strip materials. The cupping test for metal sheet thickness range is 0.1mm-5mm, Max. Punching capacity is 600KN, and the pre-tightening/clamping device is with hydraulic servo loading pump for 600kN capacity;
-
product
Motor Driven Actuator
NJ-SERVO Series
The NJ-SERVO electric motor driven actuator utilizes an electric motor drive system. High accuracy test control is enabled by a special servo motor and stroke displacement measurement sensor. In addition, the system configuration is simpler in comparison to hydraulic actuators, so it is easy to maintain, and achieves power savings and space savings. This system accommodates a wide range of tests with a high degree of expandability. This includes everything from endurance evaluations of the main body and assemblies of automobiles, aircrafts, and other transportation equipment to endurance evaluations of stand-alone parts; from multi-axis tests combining multiple actuators to uniaxial tests; and from sine waves to working waveform simulation tests.
-
product
6 Sided Bed of Nails Testers
BoxProber Family
6 sided Bed of Nails circuit board test fixture. Probes top bottom and all 4 sides. Central camming mechanism pull plates inward. Mechanically or electrically actuated options. Designed primarily for testing products in plastics. Side access electrically probes outside panel connectors. The unit will also optically read LEDs and key segments off LCD displays. Solenoids will press buttons and servos will turn selector switches. DC motors are used to adjust multiple turn potentiometers. Microphone will detect audio output tones. Top and bottom of circuit boards can also be probed if removable access panels are available. This unit will also probe all 6 sides of a circuit board. This is typically utilized in applications where connector testing is required.
-
product
Electric Servomotor Free Fall Tester
An electric servo motor type packaged cargo drop tester compliant with "JIS Z 0202 Packaged cargo-Drop test method". It is possible to test large test pieces safely, stably and quietly.
-
product
Motion Control Board, PCI
APCI-8001
*Axis control for 3 servo or stepper motors*Onboard processor*Optical isolation*16-bit analog output channels*Direct connection of commercially available incremental encoders or SSI absolute encoders*Possibility of extension to a total of 8 axes*Menu-driven test application
-
product
Brushless/Servo/Stepper Motor Tester
Shanghai Aoboor Electric Co., Ltd.
Applicable to brusheless, servo,stepper motor performance test.
-
product
Energy-Conservation Unit For Servopulser Hydraulic Power Supply Unit
ECU1/ECU2 Series
Up to 50 % energy savings. Contributes to reduced CO2 emissions and lower running costs. The conventional hydraulic power supply unit for fatigue and endurance tests is always driven at full power to achieve the maximum test force and maximum velocity and the hydraulic power supply unit is selected in order to satisfy the maximum test performance. Therefore, depending on the test conditions, energy is excessively consumed. With the ECU Series the motor rotational speed and the supply pressure of the hydraulic power supply unit can be set in multiple stages, so energy savings of up to about 50% can be achieved depending on the test conditions and test circumstances. It is used in combination with the Servo Controller 4830. (The Servo Controller 4830 is provided separately.) * Appearance and specifications are subject to change without notice.
-
product
Hydraulic Vibration Shaker
KRD70 series
KRD70 series hydraulic vibration shaker converts the energy of high-pressure liquid into the power of the reciprocating motion of the cylinder through the electro-hydraulic servo valve. Especially suitable for vibration tests requiring low frequency and high force. It can realize sine, random, multi-point excitation and shock test (sine, random, sine on random, random on random, or resonant search & dwell). It’s applied for reproducing the vibrations of transportation vehicles, bulk packaging products, machinery, electrical and electronic products in the actual environment, thereby optimizing the product structure and saving costs.
-
product
Servo Tester
105
Simulates a receiver so you can test your motors and servos without having to use a transmitter and receiver. It can send RC-PWM signal of 1ms to 2 ms in 20ms period. It connects to an ESC via three wires. The servo tester is powered by the BEC in your speed control or by a std 4 cell 5 volt receiver battery
-
product
Servopulser Vibration Testing Machine
EHV Series
This machine performs vibration tests on structures, equipment, transport packages, etc. Vibration directions include horizontal and vertical. Large capacity and large stroke can be obtained with the electro-hydraulic servo system.
-
product
Rapid Temperature Change Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Sanwood is the company capable of offering a series of Rapid ESS Test Chamber,Rapid Temperature Change Test Chamber,Environmental stress screening (ESS) test chamber,Environmental stress screening test chamber,Temperature Change Test ChamberEnergy-saving design: Adopting PID + PWM principle of VRF (refrigerant flow control) technology to achieve low-temperature energy-saving operation (electronic expansion valve according to thermal energy conditions refrigerant flow servo control technology) low temperature working state, the heater does not participate in the work, through PID + The PWM regulates the flow rate and flow direction of the refrigerant, and regulates the three-way flow of the refrigerant pipe, the cold bypass pipe, and the hot bypass pipe to achieve automatic constant temperature to the working chamber. This method can reduce energy consumption by 30% under low temperature conditions.
-
product
Motor Stator Tester
DZ901
Shanghai Aoboor Electric Co., Ltd.
Applicable to precision electrical properties test of stators of y-type three-ohase motors, single-phase motors, hub generators, brushless motors and servo motors.
-
product
Computer Servo Control Testing Machine for Rock Stiffness
YAW-G300
Jinan Testing Equipment IE Corporation
The Computer Servo Control Testing Machine for Rock Stiffness is used for static fatigue compression test for conncrete & rock material under different parameter. The test includes compression, shearing test, three-point bending testing & fatigue test. Meanwhile, the Computer Servo Control Testing Machine can also realize the automatic control, measuring, data processing; curve analyzing, result displaying and test report printing in the process of various tests. The stiffness testing system can do full process test under stress and strain.
-
product
Concrete Drainpipe Compression Testing Machine
SCT Series
Jinan Testing Equipment IE Corporation
The concrete drainpipe compression testing machine is designed for the radial compression test of drainpipe and other cement pipes which accords with "Test method of concrete and ferroconcrete drainpipe":. The concrete drainpipe compression testing system is also suitable for the compression test of other metal and non-metal materials. The concrete drainpipe compression testing machine consists of load frame, oil source, computer and servo unit. It is of compact structure and easy to operate.
-
product
Electronic Pressure Comparator
Huaxin instrument (Beijing) Co., Ltd
When it comes to simultaneous pressure calibration for several pressure measuring instruments, electronic pressure comparator is always a great choice for most of people. The comparison calibrator features 5 pressure ports which allow simultaneous connection of 4 pressure gauges under test, making calibration more efficient and time saving. It also comes with an external air source for easy and precise pressure generation and servo valve for stable pressure control.
-
product
Stator Tester
Changzhou Chanlon Electronic Technology Co., Ltd.
This machine is applied to test varieties of iron stator like pump motor, air-conditioning motor, washing machine motor, paper shredder motor, servo motor and stepper motor etc. Its LCD shows all technical data which obtained by industrial control computer, which check and verify the quality of testing stator.
-
product
Compression Testing Machine for Special Purposes
Jinan Testing Equipment IE Corporation
These compression testing machined are suitable for testing the compression strength of components or structural material such as concrete, steel, brick, rubber pad, etc. These compression testing machines feature large test space and double actions. Hand operate, analog dial or monitor. Hydraulic servo with computer control.
-
product
Closed-Loop Servohydraulic Test Bench Control System
Closed-loop servohydraulic test bench control system is based on digital devices of ZETSENSOR series with CAN interface. This system has fast response characteristics, high precision, and compact dimensions. The system enables comprehensive control of the servo drive in automated mode in compliance with the set test parameters such as pressure (force), displacement, along with the parallel control of other system parameters such as temperature, pressure, filter plugging, oil pressure, etc.
-
product
4-Channel Motion Control and High-Speed Trigger and Module for the Bridge Connected to EtherCAT
ECAT-4XMO
The ECAT-4XMO is EtherCAT slave module with high-speed position comparison trigger and encoder single redriver function, helping machine and equipment builders to use multiple triggers simultaneously for AOI, glue dispensing, display tests, and storage assembly applications. Additionally, the ECAT-4XMO has 4-axis motion control with bridge function between EtherCAT and non-EtherCAT. Advanced motion control functions help machine and equipment builders to increase their motor selection portfolio, like leaner, step, servo, direct drive, and AC motors, making it ideal for a variety of automation industry applications.
-
product
Hydraulic Universal Testing Machines
UH-X/FX Series
Environmentally and operator friendly state-of-the-art universal testing machine The operability and visibility of the computer-controlled hydraulic servo type universal testing machine (UH-X) and the high-performance universal testing machine (UH-FX), equipped with front opening type hydraulic grips, have been greatly improved by the adoption of a large color touch panel. Equipped with a semi autotuning function that automatically adjusts the control parameters, stress control and strain control (ISO 6892 compliant) can be easily carried out without the need for a preliminary test. The UH-Xh and UH-FXh models feature a new hybrid hydraulic oil source that reduces the required quantity of hydraulic oil, thereby achieving a major reduction in electrical power (about 50 %).
-
product
Digital Display Auto Torsion Testing Machine
NJS Series
Jinan Testing Equipment IE Corporation
NJS Series Digital Display Auto Torsion tester is designed and built for torsion test on metal & non-metallic materials, as well as parts & components. NJS is loaded through the rotation of the active cartridge driven by the AC servo motor and cyclonical pinwheel reducer motor. The torque and torsion angle are measured respectively by the high-precision torque transducer and photoelectric encoder. The digital torsion testing machine is an essential instrument to inspect torsion properties of materials for mechanical laboratories of aviation industry, construction industry, scientific research department, universities and industrial enterprises.
-
product
Power Cord Bending Tester
SW-6
SW-6 Power cord bending tester is fully designed according to the IEC standard, and can also be costumer-sized depends on the samples’ type and the costumer’s requirement. Specifications: • Power supply：AC220V 50/60HZ 12KVA • Control mode: PLC with touch screen and Servo motor. • Test Speed: 10~60times/min (Adjustable) • Test Degree: 0~540° (Adjustable) • Counter: 0~999999 (Can be pre-set) • Weight: 5N,10N,20N. 2Sets. (6Position type will have 6 Sets) • Position: 2/6 • Load Current: 0~20A (Adjustable) • Angle plate: Can check the test situation • Sample fixture: Can be costumer-sized. • Can do power line bending test (The User need prepare sample and power supply ), Can record the number of the sample’s work with load.
-
product
ADI Test Fixture
TA-6500
The TA-6500 test fixture combines the features of the OEM's Instrument Servo Tester(T307962), the Pointer/Flag Test Fixture(T307951) and the AD-650/600 Test Panel(T334043) all into one panel to facilitate testing of these Attitude Director Indicator's. The panel switches and adjustment pots are labeled to match the test procedure numbers and the duplicity in marking makes it easier for the technician to understand each function. The UUT interface is through a 96 pin zero insertion force(ZIF) type connector to minimize contact wear. The expanded localizer and nav input pins J2-34/35 are exposed on the panel to facilitate the insertion of a 200 ohm shunt when required. The fixtures rear panel has connectors for the required dual API/Synchro transmitter interface while the panel switches provide the correct routing of each.
-
product
Multi-Tester
GWRMT001
Grand Wing Servo-tech Co., Ltd.
◆To measure the Pulse Width transmitted by Transmitter for up to 9 channels. ◆To measure the Pulse Width sent from Receiver.◆To test the rotations of Servo automatically – at the pulse widths of top, medium and low points set by user already.◆To test the automatic rotations of Servo.◆To test the rotations of Servo by turning the knob on the tester manually .◆To test the sensitivity of Servo (1μS per step minimum).◆To measure RPM of a spinning propeller – for 2 – 6 blades ones, real time RPM value shown／to set the peak RPM value up to 99990 per minute.◆Shiny 4 digits red LED's to display the values measured.◆Power source can be from UM-4 / AAA cell x4, or an adapter with 7-15V or BEC (5V) from an ESC.◆An output port for applying Positive/Negative signals of Pulse Width from this tester.◆Four buttons for setting up functions and modes.
-
product
Testing Aircraft Tachometers
The test bench is comprised of a TMB 304 Torque Transducer and a custom fixture for the tachometer and corresponding inertia wheel. A servo motor is incorporated to provide speed to the tachometer. The entire drive train is conveniently mounted on a base plate with the appropriate couplings, bearing support and flywheel.
-
product
Erichsen Cupping Testing Machine
GBW Series
Jinan Testing Equipment IE Corporation
GBW series Erichsen Cupping Testing Machine is designed on the basis of screw universal material testing machine. The Erichsen Cupping Tester is suitable for cupping test of metal sheet and strip steel rolled stock etc to evaluate the plastic deformation performance and ductility. The cupping test for metal sheet thickness range is 0.1mm to 5mm, Max. punching capacity is 300KN, and the pre-tightening device is optional either with hydraulic servo loading pump or manual loading pump.
-
product
Servo Motor ,Precision Linear Stages
PSAXXX-11AS-X
Model:PSAXXX-11AS-X Servo Motor ,Precision Linear Stages PSAXXX-11AS-X adopt panasonic 100W or 200W AC servo motor and high level coupler,achieve high resolution,high speed,low vibrate;material is alluminum alloy by special craft; Characteristic ◆ground ball screw ,achieve high postion accuracy ◆import guide ensure straightness and parallel inconjunction with our special craft ◆strict assemble craft and test method, ensure high performance ◆servo-motor and limited swithes design, convenient for choosing controller ◆limited switches ensure safety ◆different size and travels,make products abount ◆hand-wheel achieve hand adjustment
-
product
Economical Hydraulic Manual Universal Testing Machine
WEW-D Series
Jinan Testing Equipment IE Corporation
WEW-D series hydraulic manual UTM is suitable for testing tension, compression and other strengths of various metallic or nonmetallic materials with high strength. The hydraulic manual UTM is capable of testing the characters of materials on physical & technology properties. As a manual control & economical UTM, the hydraulic manual UTM is with reasonable and reliable configurations (load cell or pressure transducer, extensometer, photoelectric encoder, servo motor & driver, standard screws), which can satisfy ordinary testing requirements. Digital controller and computer with software can be equipped on this machine to realize the test date/curve collecting and process. The hydraulic UTM of economical type is easy to operate and is versatile in the applications of metallurgy manufacturers such as steel mills & alloy, reinforced bar etc.
-
product
2-500kg Computer Servo Tensile Test Instrument
JY－106B
Shenzhen Chuangxin Instruments Co., Ltd.
The Computer Servo Tensile Testing Machine is widely to test the tensile, tear, peel and bend of all kinds of
-
product
Structural Durability Products
Instron offers a wide range of Durability Testing Products such as Controller and Software modules, Hydropuls actuators (linear & rotary), Servo valves, Sensors, Power Packs & Accessories and Test frames & fixtures.
