Filter Results By:
Products
Applications
Manufacturers
- Virginia Panel Corporation
product
Tool, Extraction, 50 Ohm Coax & Power Surface
910112112
Tool, Extraction, 50 Ohm Coax & Power Surface
-
product
Toolmakers Microscope
Sinowon Innovation Metrology Manufacture Ltd.
It is widely used in mechanical, meter, electronic and light industry; university, Institute and metrology department. The measuring profile projector can detect the contour dimension and surface shape of variety complex workpiece, such as templates, punching pieces, cams, threads, gears, molding milling cutters.
-
product
AOI & SPI, Test Systems
SigmaX SPI
Most defects in the circuit-board assembly are due to the solder paste or the process of printing solder paste. Since the transition to lead-free soldering, a whole new spectrum of problems has emerged in older paste printing and its due processes. Incomplete coalescence of ball grid array (BGA) spheres and solder paste deposits are failure modes that have increased in frequency since the transition to lead-free soldering. The SigmaXs inspection technology is unaffected by varying materials, surface conditions, or colors. The system profiles the board to generate accurate 3D shapes far superior to other brands and technologies.
-
product
5G 256-Element Active Antenna Innovator’s Kit
AWA-0134
The AWA-0134 is an active array for 5G wireless applications developed using planar antenna technology resulting in a very low profile, lightweight unit. The surface mount assembled antenna board is based on Anokiwave’s AWMF-0108 Silicon Quad Core IC and demonstrates the performance achievable using low power silicon integration and efficient antenna layout and design. Using the AWMF-0108, the antenna provides +60dBmi (1000 W) of EIRP. The electronic 2D beam steering is achieved using analog RF beam forming, with independent phase and gain control in both Tx and Rx operating modes. The AWA-0134 antenna leads the way in showing how 5G coverage can be rolled out by network operators using the mmW bands, with low power footprint and high energy efficiency, while meeting key operating specifications for data rate, latency, coverage, and reliability.
-
product
Non-Destructive Subsurface Layer Profiling
NMR-Mouse one-sided NMR
The unique, powerful Profile NMR-MOUSE® probe works hand-in-hand with the Kea2 spectrometer. The Profile NMR-MOUSE is a portable, open NMR sensor equipped with a novel permanent magnet geometry that generates a flat sensitive volume parallel to the scanner surface. The system can measure *Proton density as a function of depth *T2 NMR relaxation times *T1 NMR relaxation times *Self-Diffusion coefficient of liquids
-
product
ElcoMaster Oven Profiling Software
*Oven Logger set up & programming*Paint/Powder parameter library*Product probe maps*Fully customisable inspection templates*Selectable probe/channel traces*Statistical analysis by probe/channel*Max, Min, standard deviation, coefficient of variation*Temperature profile, cure progress, histogram & individual cure value graphs against product*Time at temperature, time of peak difference*Time above maximum absolute & minimum cross link temperatures*Fully customisable inspection reports*Combined reports - coating thickness, gloss, adhesion, profile, climate, surface cleanliness*Report generator wizard & PDF generator*Email or export data*Import photo’s, data sheets, critical data, inspection notes, etc & include on inspection reports*Cloud computing - allows for cross site collaboration, including internal text messaging tool*Overlay temperature profiles, review and compare multiple oven profiles over time*Use additional data loggers for multiple channels or run overlays
-
product
Digital Surface Profile Gauge
224
Measurement capability to ±5%Can be used in accordance with National and International StandardsTemperature stable measurementsStatistics are calculated and displayed in real timeLive and batch readings graph format for instant analysis
-
product
Contour Check Shape
Contour Check Shape has proven itself in hot rolling of long products and is an essential part of the rolling process in many factories. It checks hot and cold steel profiles with the help of three-dimensional surface reconstruction. Thus, it records geometrical errors due to rolling defects including surface defects like scale seams, shells or roller outbreaks.
-
product
Contour Check Round & Edge
Laser measuring systems are of central importance for rolling mills to check the contours of steel profile for defects during the production process. A slight deformation on the surface of the profiles reduces the quality of the product, and in the worst case, a broken roll can even destroy the entire batch. With our systems Contour Check Round & Edge you identify and evaluate deviations at an early stage. Increase the process efficiency of your production - regardless of temperature and profile shape.
-
product
Ocean Observer III
Teledyne Marine RD Instruments
Since 1997 Teledyne RD Instruments has been providing ADCPs that have proven in the field they can profile beyond 1000 m from research vessels traveling at speeds >15 knots and from offshore oil and gas platforms during exploration work. That same technology has now allowed us to create the Ocean Observer III 38 kHz ADCP. We have combined our field-proven 38 kHz phased array ADCP transducer with our field-proven electronics into a single package that is capable of profiling >1000m. This design makes it ideal to be mounted from an oil platform, over the side of a vessel, and in surface buoys.
-
product
Metal Thickness Measurement
Micro-Epsilon offers innovative measurement and inspection systems for the metals industry. Latest technologies are used for thickness, profile and surface measurements. Performance and quality, as well as reliability of products and services have made Micro-Epsilon one of the leading suppliers of inspection systems for optical thickness measurement used in the metals industry. Numerous, successful installations in 13 countries around the world in milling lines and processing lines speak for themselves.
-
product
Fatigue Testing And Certification
Fatigue engineering is subject to uncertainty, and data from well executed tests are used to validate conclusions made by analysis and to provide a basis for structural certification. Our staff have extensive experience in testing materials and components under slowly varying, static loads, and under rapidly varying cyclic loads. Tests under static loads are used to assess material properties or to assess the load-deformation behavior of structural components. Tests under cyclic loads provide time to crack initiation, time to failure, or measurements of crack growth over time. We have extensive experience in measuring fatigue crack growth behavior in metallic materials. Past programs have measured crack growth with microscopy and photogrammetry at the surface, cracked area with direct current potential drop, and through-thickness crack profiles with quantitative fractography. By assessing crack growth with a variety of experimental methods, we enable robust analysis validation for cases of complex cracking. Our capabilities in fatigue engineering allow for careful design of a fatigue test program. Whether the tests use constant amplitude loading or an irregular loading spectrum, we specialize in engineering the test that meet your needs. Much of our experience is in non-standard test programs, which require engineering to optimize the test setup. Few others match our capability and experience in fatigue test engineering.
-
product
Atomic Force Microscope
3DM Serirs
Park Systems has introduced the revolutionary Park 3DM Series, the completely automated AFM system designed for overhang profiles, high-resolution sidewall imaging, and critical angle measurements. With the patented decoupled XY and Z scanning system with tilted Z-scanner, it overcomes the challenges of the normal and flare tip methods in accurate sidewall analysis. In utilizing our True Non-Contact Mode™, the Park 3DM Series enables non-destructive measurement of soft photoresist surfaces with high aspect ratio tips.
-
product
Surface Profile Gauge
SRT-6223
Specially used to take accurate measurement of the peak to valley height of the surface profile of the surface profile of blast cleaned surfaces.specifications:display: 4 digits. LCDRange: 0um to 800um (0mils to 30mils)Accuracy: +5% or +5( whichever is the greater)resolution: 1um (0.1mils)Metric and Imperial switchablePC interface: RS232CMeasurement speed: >30readings per minuteweight: 280gdimensions: 162x65x28mm(6.4x2.6x1.1 inch)operating temperature: 0-50℃ , 80% RHCase: high impact ABSBatteries: 4x1.5v (AAA) Batterystandard accessories included:carrying case: 1 pcoperation manual 1 pcoptional accessory:cable and software for RS232C
-
product
256-Element Active Antenna Innovator’s Kit
AWA-0142
The AWA-0142 is an active array for 5G wireless applications developed using planar antenna technology resulting in a very low profile, lightweight unit. The surface mount assembled antenna board is based on Anokiwave’s AWMF-0135 Silicon Quad Core IC and demonstrates the performance achievable using low power silicon integration and efficient antenna layout and design. Using the AWMF-0135, the antenna provides +60dBmi (1000 W) of EIRP. The electronic 2D beam steering is achieved using analog RF beam forming, with independent phase and gain control in both Tx and Rx operating modes. The AWA-0142 antenna leads the way in showing how 5G coverage can be rolled out by network operators using the mmW bands, with low power footprint and high energy efficiency, while meeting key operating specifications for data rate, latency, coverage, and reliability.
-
product
Analog Surface Profile Gauge
NOVOTEST LIMIT
Mechanical depth gauge is designed to comply with ASTM D 4417-B, SANS 5772, US Navy NSI 009-32, US Navy PPI 63101-000 for (depending on configuration): measures the peak-to-valley height of a blast cleaned surface; measurement the depth of focal corrosion; measures depth of narrow holes and grooves.
-
product
Magnetic Profile Measurement
Many times it is requires to study the magnetic field profile of the 2D or 3D surface to estimate the performance of the magnetic device. The field pattern is measured by sensors and very precise mechanical arrangement. The spacing between two points of measurement can be as low as a few microns. This precise measurements can confirm the quality of performance of any device.
-
product
3D Machine Vision Systems
Whether performing a single profile measurement or scanning an entire surface in 3D, Cognex has the most powerful and robust 3D machine vision tools. Manufacturers in all industries trust Cognex technology to deliver high accuracy surface feature measurements that go beyond the capabilities of 2D machine vision technology.
-
product
Mini Load Column Load Cell Compression Only with Mounting
MLC SERIES
The MLC Series is our miniature high capacity compression only load cell/force sensor, featuring low profile compact size for a wide range of portable and dedicated applications up to 30,000 lb The load diameter is slightly convex for accurate load distribution. Low deflection through design results in ultra fast frequency response. The MLCs are designed to be mounted in a shallow machined flat pocket or smooth flat surface, either free or fastened via a bottom 6-32 tapped hole. These load cells are manufactured from heat treated 17-4 ph stainless steel. The sensing element incorporates bonded foil strain gages of the highest quality and are sealed for protection against most industrial Environments.
-
product
Protective Inspection Kit for Hazardous Areas
The kit provides all the tools required for the on-site inspection of a coating, including surface profile, dewpoint, relative humidity, both wet and dry film thickness and also adhesive testing.Measurement parameters include:Surface inspectionSurface profileSurface contaminationClimatic conditionsCoating thicknessAdhesion
-
product
Surface Profile
Surface profile: The degree of profile on the surface affects a coating’s overall performance and determines aspects such as adhesion, coverage and overall volume of coatings used. If the profile is too large the amount of coating required increases, otherwise there is a danger that the peaks remain uncoated - allowing rust spots to occur. If the profile is too small there may be an insufficient key for adequate adhesion.
-
product
Rhopoint IQ 20/60/85
A6000-011
The Rhopoint IQ quantifies surface quality problems that are invisible to a standard glossmeter and profiles how light is reflected from a surface. In one button click, the instrument measures gloss, haze, DOI (orange peel), RIQ and RSPEC making it the ideal choice for high gloss applications
-
product
Digital Surface Profile Gauge
NOVOTEST SP-1M
Digital Surface Profile Gauge NOVOTEST SP-1M is designed for profile measuring on either flat or curved surfaces. Also it can be used for measurements of surface roughness (Rz), after abrasive blasting pre-painting work.
-
product
General Purpose Low Profile
Our low profile load cells feature an advanced structural design that makes them extremely durable, accurate, and resistant to large extraneous shear and moment loads. To perform in a linear and predictable manner, the outside diameter of the load cell must be bolted to a flat rigid surface. When this is unavailable, our factory installed base provides a convenient threaded attachment point for easy installation and use in both tension and compression. All low profile load cells are stocked with the mounting base installed, but we can remove the base upon request.
-
product
Harness Design and Manufacture
When designing an underwater cable harness, there are some factors which need to be considered, and we have produced the following list as a guide for customer information:Component considerations:- Electrical requirements- Mechanical considerations- Quality requirements- Reliability- Design redundancy (contact count)- Connector selection (type and form)- Locking requirements- Backpotting requirements- Waterblocking in moldings- Cable specification- Cable jacket material and compatibility with elastomers- Abrasion resistance- Stiffness profile at termination- Connector format (straight or right angle)- Molding format (straight or at an angle)- Clearance allowance for molding and cable routing- Elastomer compatibility (eg oil filled units)- Metalwork selection re: corrosion and cathodic delamination- Surface finish for metalwork as appropriateOperational considerations:- Operating depth profile (not just max. depth)- Tensile loads- Torsional loads- Bending loads- Bend control requirements (to limit bending at termination)- Deployment and recovery loads- Dynamic loading-Flow turbulence effects.
-
product
Surface Roughness Tester Profilometer
TIME®3231
Beijing TIME High Technology Ltd.
TIME® 323X series is advanced high-end surface roughness measuring instruments with wide testing range (±400µm) and high accuracy (tolerance±5%, repeatability 3%). Meanwhile, TIME® 323X surface roughness tester features with skidless/skid measurement, which means it can reach smaller and harder to reach parts than other conventional tools. Up to 55 paramenters for roughness, waviness and primary profile are supported. Apart from those features mentioned above, TIME®3231 is loaded with 90° measurement function.
-
product
Surface Profile
Surface profile: The degree of profile on the surface affects a coating’s overall performance and determines aspects such as adhesion, coverage and overall volume of coatings used. If the profile is too large the amount of coating required increases, otherwise there is a danger that the peaks remain uncoated - allowing rust spots to occur. If the profile is too small there may be an insufficient key for adequate adhesion.
-
product
Surface Profile Gauge
123
The Elcometer 123 Surface Profile Gauge is an easy to use analogue gauge which measures the peak-to-valley height of a blast cleaned surface in a similar way to the Elcometer 224 Digital Surface Profile Gauge.
-
product
SURFACE PROFILE GAGES
Steel is often abrasive blast cleaned or otherwise roughened prior to painting. The peak-to-valley height of the resultant surface profile is an important factor in the performance of applied protective coatings. Low profile may reduce coating bond strength (adhesion). Too high and the peaks may receive insufficient coverage and possibly rust prematurely. The costly application of more coating may be required if the profile is too high. For these reasons, surface profile should be measured prior to coating application to ensure that it meets contract specifications.
-
product
3D Wafer Metrology System
7980
Chroma 7980 Wafer Metrology System applies White Light Interference Measurement Technique to perform nondestructive and rapid surface profile measurement and analysis.
-
product
PosiTector Inspection Kits
PosiTector Inspection Kits contain a PosiTector gage body (Standard or Advanced) and 3 probes – coating thickness, environmental and surface profile, as well as, accessories in a convenient hard shell carrying case.
