Filter Results By:
Products
Applications
Manufacturers
Test Boards
See Also: Board Test, Testboards, DUT, Extender Boards
-
product
Board Test Fixture Probes
Offering a wide range of standard spring contact probes to meet your testing requirements and has long been recognized as the world’s largest probe manufacturer. With over 60 different probe series ranging from 0.02" (0.51 mm) to 0.187" (4.75 mm) pitch with multiple length, travel, ICT, lead free and rotator options, we provide a full portfolio designed for general purpose test on bare boards, loaded printed circuit boards and surface mount assemblies.
-
product
Meter Test Board
MTB-3200
Run standard meter accuracy tests and complex meter accuracy tests under widely varying loading conditions with TESCO’s Meter Test Board (MTB-3200). TESCO’s Three Phase Meter Test Board (MTB-3200) is an innovative meter accuracy test system offering unsurpassed functionality and ease of use. All of the features needed to test meters today and tomorrow are standard.
-
product
Debug Fixture
With at-speed test, debug can easily become a problem: If test points are on the bottom, as is often the case for test processing, then this requires the board to be flip over for the debug. However, during at-speed testing, key devices and signal paths are often on the topside. IST Engineering has in-house expertise with debug fixtures, which allow the test technician to flip over a test board, or even hold it vertically for dual-sided access, while still running the Device-Under-Test at full-speed through card-edge connectors - whether these are standard DIN type or F or N type co-ax connectors. The debug stations are constructed robustly, with metal frames and high-grade flexible cabling and can also be used as backup test stations in a manufacturing flow. They can be built with custom machined waveguide connections for RF/Microwave applications, or with standard, off the shelf connectors, as defined by the application. A number of these debug fixtures are in production use with a range of customers.
-
product
Test Board For QSFP28 Transceiver
EQSFP28
The OPTELLENT EQSFP28 is a cost-effective and convenient test board for testing QSFP28 optical transceivers in R&D and manufacturing environments. The EQSFP28 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The EQSFP28 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
Test Systems
In-Circuit Test (ICT) tests populated circuit boards by means of electronic measurements through thin needles on test fixtures. We offer in-circuit testers for various testing strategies – from the flexible 19“ rack to the ergonomic high-performance tester. And all of our in-circuit testers are also available in the Lambda edition for true parallel testing. The flying probe test checks your printed circuit boards using four movable test heads. This requires no fixtures and allows for flexible test program generation. That makes our flying probe test systems ideal for a high mix of printed circuit boards and small to medium test volumes, such as for prototype testing.
-
product
Kelvin Test Contactor
ecoAmp
ecoAmp™ Kelvin test contactor has a durable monolithic pin design with low and stable contact resistance. It is a high-power cantilever kelvin contactor with a patented spring and tip design for optimum heat dissipation. This ensures best reliability, long spring life and high yield even under highest current and temperature requirements. Featuring extended Automotive temperature range -60 ̊C to +175 ̊C, capable to stand thermal stress during high-power test. The contact motion is decoupled from the test board.
-
product
Test Fixture Kits
Our test fixture kits provide cost effective solutions to printed circuit board testing and other devices under test. Our modular kits are available in multiple sizes and configurations. They can easily be customized if our standard doesn’t meet your requirements. Removable side panels for ease of fabrication for I/O connections, switches or other hardware.
-
product
Software & Hardware Interface
XJAPI
The XJAPI is a simple-to-use DLL Application Program Interface (API), designed to give you low-level access to the JTAG chain via either the XJLink or the PXI hardware, allowing easy integration with a wide range of other systems such as development/evaluation boards, test systems
-
product
K-Base Test Board Adapter
1180
The TESCO K-Base Test Board Adapter allow quick, convenient testing of self-contained K-Base meters on test boards designed for socket type meters. The K-Base Test Board Adapters are designed for single phase (Catalog No. 1180-2) and polyphase (Catalog No. 1180-4).
-
product
Vacuum Test Fixtures
Series 63
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
product
Test Adapter
cPCI/VME/VME64x
The test adapter is used for measurement and testing of test specimen boards, which gives optimal access of signals, address lines as well as power from backplane assembly. Usually the test adapter includes fields for voltage and amp, current measurements and in some cases also some pins for wire wrap to conduct custom connections.
-
product
VME Test Extender 6U/220mm Universal
110EXT6122-000X
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Actuation Methods for In-Circuit Test Fixtures
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
product
Backplane Test System
402HV
Our model 402HV is the result of 25 years of high voltage / high pin count test systems experience. We produced our first high voltage system back in 1985. It was programmable up to 600 volts / 600 Mohms and had over 49,000 test points. It could test a 5k point board in less that 15 seconds. Since then we have built hundreds of high voltage test systems, with our highest voltage system capable of testing up to 2000 Volts DC / 1500 Volts AC. (One of our 600 volt systems, built in 1986 is still in operation testing boards for a defense contractor.)
-
product
Clamshell Type Mechanical Fixtures
Series 31
The GR Series 31 dual well mechanical kits provide a solution to printed circuit board testing that requires the benefits of GR2270 style (VG) interface compatibility and the advantage of testing two devices on the same test fixture. These can be similar devices, or devices that are used together in a functional test.
-
product
VME Test Extender 3U/220mm J2
111EXT3122-12XX
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
Power-off Circuit Board Testing
Huntron® Trackers®
Adding diagnostic tools to enhance your circuit board test capabilities is an important part of any electronic repair environment.Huntron Tracker power-off circuit board test uses analog signature analysis to detect and isolate component faults on boards beyond power-on functional testing. By comparing Tracker signatures from a working circuit board to the signatures of a non-working board, you can troubleshoot down to the component level.
-
product
MDA
TR518 SII INLINE
*Automated In - Line platform cost effective. *Flexible automated testing platform designed for MDA testing on medium-sized boards
-
product
Printed Circuit Board Testing Solutions
IES Systems is a turnkey test systems solution provider with 10 years of proven experience in printed circuit board testing solutions. Our experienced engineers design electro/mechanical solutions to interface between your product and our custom designed test instrumentation. We provide a complete solution to your PC board testing needs.
-
product
FMC Loopback Test Board
The FMC loopback tester board enables developers and assembly factories to test and characterize the FMC carrier board interfaces. The board features full differential loopbacks on all the FMC high pin count (HPC) connector interfaces including LA, HA, HB, DP and CLK. It also provides a 125MHz transceiver LVDS reference clocks on GBTCLK signals. The FMC loopback board is based on VITA 57 standard with ruggedized conduction or air cooling.
-
product
Test Set
TS® 22
The TS22 Test Set’s unique built-in one-way amplified speaker provides three audio levels for hands-free listening and use with automated voice response systems. Multiple memories enable storage of nine 18 digit telephone numbers in repertory dialer (speed dialing) for easy access to test boards, the central office and other frequently called numbers. The last number redial feature eliminates the need to re-key your last entry. The TS22 Test Set offers an unbeatable combination of reliability, durability and expanded utility.
-
product
Three Phase Meter Test Board
MTB-3050
TESCO’s MTB-3050 is a Three Phase Meter Test Board with every laboratory feature you could want along with metrology and software suitable for your production meter testing needs.
-
product
Clamshell Type Mechanical Fixtures
Series 70
The VP Series 70 Mechanical Test Kits provide a solution to printed circuit board testing using the Virginia Panel ITA G12 Interface.
-
product
Differential Sensor, Wide Dynamic Range, 100 MHz
CX1105A
The CX1105A ultra-low noise differential sensor is a dedicated accessory for the CX3300 series and enables dynamic current measurements from 1 μA to 100 A under up to 100 MHz bandwidth with existing shunt resistors on your test board.
-
product
Clamshell Type Mechanical Fixtures
Known in the ATE Industry as “Clamshell” type Test Fixtures, Semco’s Mechanical Test Fixture line is a cost-effective solution to test Printed Circuit Boards and Assemblies. This Test Fixture line is also available with the most widely used interfaces in the test industry.
-
product
Test Board For SFP+ / SFP28 Transceiver
ESFP280
The OPTELLENT ESFP280 is a cost-effective and convenient test board for testing SFP/SFP+/SFP28 optical transceivers in R&D and manufacturing environments. The ESFP280 is equipped with high quality RF connectors for data signals and test points for low frequency control and status signals. The ESFP280 is equipped with power supplies to enable voltage margining. Key status signals are displayed using LED indicators.
-
product
High Current Probes
The maximum continuous current rating of a spring probe is determined by its design, size, and construction. Typical probes are rated from 2 to 8 amps maximum continuously current at working travel. While this is sufficient for most board test applications, higher current applications will require a much more solid and rugged probe to withstand current capabilities of 10 to 150 amps and beyond.Another high current solution is our feed-through plunger probe line. As the name already describes, the plunger moves right through the probe and is made from a single piece, reducing the internal resistance of the probe to a minimum.
-
product
VME Test Extender 9U/400mm J1/J2/J0
111EXT9140-0120
The VME extender boards are designed to bring a circuit card completely out of a card cage so that it can be tested or debugged on both sides of the test board. Each signal, power, and ground line can be individually isolated with the DIP switches.
-
product
DUT Prototype Board
DPB8800
The DPB8800 is an 11? x 14? PC board used to interface the tester with the Device Under Test (DUT). This board contains generous area for custom circuitry and extra relays. The DPB8800 is also available with standard solutions to test families of components like Op-Amps, Regulators, ADC?s and DAC?s. +/-15 V and +5 V are available to support circuitry biasing.
-
product
Flying Probe Test
Producing the highest quality test programs since 2005, Test Coach is the proven specialist firm for flying probe test. Our in depth knowledge of SPEA systems and over 10 years of honed flying probe test techniques guarantees that our test programs offer the highest test coverage possible. As an In – Concert Partner with SPEA, we work closely with their team to keep at the forefront of new product innovations and technology, so that we can provide the latest advancements to our customers. In addition to test program development, we offer board test services, maintaining the systems and staff that allow for high throughput and the ability to consistently deliver the rapid turn times that customers can depend on. And, with 7,000 square feet of space, we feature a modern, clean, ESD safe and ITAR registered facility that surpasses expectations.
