Filter Results By:
Products
Applications
Manufacturers
Token Ring
-
product
Multi-Network Cable Tester
3PK-NT007N
Multi-network cable tester is specified to quickly test by auto scanning the wires continuity, miss-wiring and polarization in your network cables, thin Ethernet (BNC)/10 Base-T (UTP/STP)/356A/ TIA-568A/TIA-568B/Token Ring. By using the attached remote terminator, you can easily test the cable whatever before or after the cables installed. It also allows you to test the ground of shielded twisted pairs cables.
-
product
Multi-Modular Cable Tester
MT-7051N
Tests RJ45 TIA568A/B (AT&T 258A), 10 Base-T, Token ring, RJ-11/ RJ-12 USOC and Coaxial BNC cable.Automatically check cable for continuity, short, open and crossed wire pairs.Coaxial cable port indentifies cable conditions including shorts, shield opens and center conductor breaks.Main unit and remote allow one person testing.Power source: DC 9V BatteryDimension: 102x106x28 (mm)Cable not include
-
product
Line Tester
CAT 1 TEST
Monacor International GmbH & Co. KG
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
product
Lan Cable Tester
185 LCT
Standard Electric Works Co., Ltd
● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable.● The LAN cable tester can verify cable continuity, open, short circuit and miss-wired.● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan functions.● Ground wire test. ● Lock status function.● Buzzer sound warning for wire status.● Display : LED indication for wire status.
-
product
Network Analyzer, Lan Tester, LED
72-6706
The Tenma Multi-Network and Modular Cable Tester easily reads the correct pin configuration of 10Base-T cable (Category 5, 5e and 6), 10Base-2 cable (coax), RJ-45 and RJ-11 modular cables, 356A, TIA-568A/568B and Token Ring cable by comparing transmitting end to the corresponding receiving end
-
product
Cable Tracer and Digital Multimeter
187 MCT
Standard Electric Works Co., Ltd
Lan Cable Tester● Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.● The LAN cable tester can verify cable continuity, open, circuit and miss-wired. ● The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.● Auto and manual scan function.● Ground wire test.● Display : LED indication for wire status.Digital Multimeter● 4000 counts LCD.● Full automatic measurement. Voltage measurement. Resistor measurement.● Range change function.● Select function.● Data Hold function.● Continuity check.● Diode measurement.● Low battery indication.● Input impedance:10MΩ.
-
product
Lan Cable Tester
Shanghai Beha Electronics Co., Ltd.
Designed for RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.• The Lan cable tester can verify cable continuity, open,short circuit and miss-wired.• The remote receiving unit is available for installed cables far away either on the wall plates or on the patch panels.• Auto and manual scan function.• Ground wire test.• Lock status function.• Buzzer sound warning for wire status.• Display: LED indication for wire status.
-
product
Lan Cable Tester
Shanghai Beha Electronics Co., Ltd.
*is a newly designed tool,that can easily test the correct pin configuration of the RJ45/RJ11 modular cables, 10/100 base-T cable and Token Ring cable etc.*by comparing one transmitting end and the corresponding receiving end, the 9185B Lan cable tester also can test installed cable far away by using the remote receiving unit.*provides the variety for wiring check, such as cable continuity, open status, short status and miss wired.
-
product
Mini Lan Cable Tester
MT-7058
Complies with CE safety standardAutomatically detect good connections, opens, crossed wires & split pairsTest RJ45 TIA568A/B (AT&T) 258A), 10 Base-T, Token ring, RJ-11/RJ-12 USOC and coaxial BNC cablePin to pin cable map indicatorNon-contact voltage detection for user safetyTraces wires with tone & remote lights allows one person operationCompact size and lightweight design for easy to carry aroundCircuit Protection for both units to ensure the testing qualityLow power consumption with auto power off function to preserve batteryLong cable test more than 300 meters
-
product
Slip Rings Separates
Separates are typically rings and insulation material assembled on an axis along with separate contact brushes. They are usually designed with flying leads. Once integrated, they provide electrical contact between stationary and rotating parts of a slip ring assembly. They use bearings from the host system and provide a more compact and economical solution than self-contained Slip Rings. The coupling of these items requires technical skills from the OEM and is suitable for applications that have tight mechanical requirements.
-
product
Capsule Slip Rings
Capsule Slip Rings are compact slip rings that can be used in a wide range of applications. They integrate rotor, stator, brush block, bearings and casings and enable the transmission of power and data through rotating systems. They are ready to be integrated into customers’ systems and provide built-in protection from humidity and dust.
-
product
3-Component Quartz Force Rings
260 Series
Three-component quartz force ring sensors are capable of simultaneously measuring dynamic force in three orthogonal directions (X, Y, and Z). They contain three sets of quartz plates that are stacked in a preloaded arrangement. Each set responds to the vector component of an applied force acting along its sensitive axis. 3-component ring force sensors must be statically preloaded for optimum performance. Preloading provides the sensing elements with the compressive loading required to allow the proper transmission of shear forces. Versions are available with ranges up to 10k lb (45k N) in the z-axis (perpendicular to the top surface), and up to 4000 lb (18k N) in the x-and y (shear) axes. Both ICP® and charge output styles are available.
-
product
Ring Wave Simulators
Suzhou 3ctest Electronic Co.,Ltd.
Ring wave interference on electronic line, control line and signal line can be caused by transient due to switch of mains and controlled switch or lightening strike. RWS 600 is designed to conduct immunity test for electronic and electrical device.
-
product
Pancake Slip Ring
Pancake or Platter Slip Rings are a specialty for EVERAXIS USA. All drum style Slip Rings can be reconfigured into a Pancake design. Choosing one or the other is highly dependant on the geometric constraints of the system.
-
-
product
Miniature Concentric Ring Set
PRF-912B
- Measures Surface Resistance from 0.9Ω to 1.0x1012Ω- Approximates Measurements Typically Obtained when using ANSI/ESD STM11.11- Spacing Allows for Measurement Area of 0.32 inches (8.13mm)- Spring Loaded Center Electrode Surrounded by 10 Contact Electrodes- Includes Conductive Rubber Covers- Certificate of Calibration Traceable to NIST included
-
product
Custom Pogo Pin Rings & Blocks
Reduce your cost-of-test with our pogo pin blocks and interfaces that transform complex DUT boards or breakout boards into universal motherboard-style interfaces. Eliminate the need to purchase or build a new board for every unique device, unit, or package.
-
product
Proving Ring
Morehouse Instrument Company Inc.
The Morehouse Digital Proving Ring reduces operator error and keeps the known stability of a Morehouse analog proving ring. Digital proving rings measure deflection of the ring in electronic "counts", rather than by a mechanical micrometer. This information can be interfaced to a computer, so data can be electronically logged, and the entire process can be automated programmatically. Calculations can be faster, with less operator action.
-
product
Slip Ring Tester
The SRT is an automatic test system offering fast and accurate measurement and reporting of noise, contact resistance and insulation resistance. It’s been designed to improve QA for manufacturers of slip rings, commutators, rotary connectors. It can also be used to test devices coming back for repair and overhaul.
-
product
Ring Disk Electrode
This ring-disk type electrode developed by NTT Advanced Technology Corporation is a form of printed electrodes. Users can choose them from Carbon, Gold and Platinum applied versions. Available as a working electrode of radial flow cells, achieves complete reduction/oxidation on the center disk at ultra-low flow rate because of its fine coulometric electrolysis efficiency. This also enables to analyze subsequent reaction as well as identification and quantitation of the sample at the same time.
-
product
3-Component Quartz Force Rings And Links
Three-component dynamic force sensors are offered in both ICP® and charge output configurations for dynamic and quasi-static force measurement applications. Each utilizes an array of precision aligned, quartz sensing crystals. Measurements along the z-axis are proportional to applied compression, tension and impact forces. Measurements along the x and y axes are proportional to shear forces that are imposed upon preloaded crystals by the test fixture.
-
product
Spectrally Flat Class B Pyranometers with Shadow Ring
LPPYRA12… Series
The LPPYRA12 are pyranometers classified as Spectrally Flat Class B (First Class) in accordance with ISO 9060:2018 and according to the WMO.
-
product
Measuring Devices For Drawing Rings And Punches For 2-part Can Production
RINGMASTER - The Benchmark For Accuracy
Optik Elektronik Gerätetechnik GmbH
High-precision, non-contact measurement of inside and outside diameter, roundness (inside and outside) and concentricity of drawing rings for 2-piece can production. The Ringmaster sets standards in measuring accuracy, user friendliness and reliability and is therefore used in can factories on all continents.
-
product
Opto Electrical Slip Rings (Electrical and FORJ Combined)
Opto Electrical Slip Rings are a combination of fiber optic rotary joints (FORJ) with gold, silver or carbon contacts. High data rates are transmitted through the FORJ while power and other signals are transferred through a contact technology.
-
product
Schottky Barrier Ring Quads
SemiGen’s Silicon Schottky Diodes are designed for applications through 40Ghz. The special process technology utilizes various metal schemes to provide excellent performance of Low, Medium, and High Barrier applications. The end result is a low resistance diode with tightly controlled capacitance which allows for optimum performance. Low conversation loss and superior TSS make these diodes ideal for detector / mixer applications with frequency ranges from S band to Ka band as well as modulators, lower power limiters and high speed switches.
-
product
Power, Patchcord, ITA, 36", High Power, 2 AWG, to Ring Terminal (150 Amps)
7-222902688-036
Power, Patchcord, ITA, 36", High Power, 2 AWG, to Ring Terminal (150 Amps).
-
product
Ring Wave Generator
SKS-1206IA/SKS-1206IB
Shanghai Sanki Electronic Industries Co., Ltd.
The ring wave generator is fully compliant with the new standards of IEC61000-4-12 and GB/T17626.12. The interface contains standard differences between IEC and Chinese national standards. Users can choose to enter the corresponding interface to perform different Test: Program -controlled high-voltage power supply and electronic switch have the characteristics of high precision, long life and good reproducibility.
-
product
Ring Laser Inertial Navigation and Weapon Stabilization System for Defense Applications
MK31 INS
The MK31 is a ring laser gyro (RLG) inertial navigation system that provides accurate heading, attitude and positional data for a wide range of naval vessels including frigates, patrol vessels and submarines. It is ideal for customers seeking a cost-effective and reliable solution for navigation and control of onboard radar, weapon, and satellite systems.
-
product
Through Bore Slip Rings
Through Bore Slip Rings are used in applications where the customer requires the bore space for some other capabilities (cooling or air media; optical or RF channels, etc.). The Slip Ring can be designed to accommodate a wide variety of bore sizes.
-
product
High Speed Slip Rings
High Speed Slip Rings transfer power and data in rotating environments at speeds of up to 20,000 rpm. They provide low noise, high reliability and long life.
