Filter Results By:
Products
Applications
Manufacturers
Communication Protocol
set of rules governing the formatting and handling of communication systems.
See Also: Communication, Protocol, COMM, Spacewire, Near Field Communications, Modbus, Data Communications
- TEAM SOLUTIONS, INC.
product
BusFinder Protocol and Logic Analyzer
Acute BF7264B+
*Two-in-One Analyzer (Protocol and Logic)*PC-based, 64 channels*USB 3.0 interface, 12V power adapter*32Gb total memory*NOW supporting MIPI D-PHY 1.2 (includes MIPI CSI)*NOW UFS2.1 supported with new BF7264B+
-
product
Wideband Radio Communication Tester
CMW500
The R&S®CMW500 wideband radio communication tester is the universal test platform for RF integration and protocol development. It is available as the R&S®CMW500 callbox and the R&S®CMW500 protocol tester. The R&S®CMW500 includes a fully integrated end-to-end data solution that permits comprehensive IP throughput and quality measurements. Thanks to the internal fading simulator, it is easy to perform tests under realistic propagation conditions.
-
product
PXIe-7822, PXI Express Digital RIO with Kintex-7 325T FPGA
783486-01
Kintex 7 325T FPGA, 128 DIO, 512 MB DRAM, PXI Digital Reconfigurable I/O Module—The PXIe‑7822 is a reconfigurable I/O (RIO) device that features a user-programmable FPGA for onboard processing and flexible I/O operation. With LabVIEW FPGA, you can individually configure the digital lines as inputs, outputs, counter/timers, PWM, encoder inputs, or specialized communication protocols. You can also program custom onboard decision making that executes with hardware-timed speed and reliability. Each line offers software-selectable logic levels. The PXIe‑7822 supports peer‑to‑peer streaming for direct data transfer between PXI Express modules. The PXIe‑7822 is well-suited for a wide variety of applications, such as high-speed waveform generation, sensor simulation, hardware‑in‑the‑loop (HIL) test, bit error rate test, and other applications that require precise timing and control.
-
product
High Resolution Encoders
HR-E
The High Resolution 8-dial Encoder (HR-E) from Badger Meter uses a non-contact field-proven light emitting diode technology to provide a high resolution 8-digit reading while at the same time eliminating friction and wear of traditional mechanical encoders. The HR-E communicates using the industry standard ASCII communication protocol to provide high resolution encoded output.
-
product
Powered VXI Crates
VXI – (VME eXtension for Instrumentation): The demand for a compact, both flexible and fast industry-standard instrument-on-a-card architecture has driven the development of the VXI standard. The modular form factor, high bandwidth, and commercial success of the VMEbus made it particularly attractive as an instrumentation platform. The tremendous popularity of GPIB also made it attractive as a model for device communication and instrument control protocols.
-
product
4DI/4 Relay Output Modbus RTU Remote I/O
ND-6160
The NuDAM modules provide direct communications with a wide variety of sensors; perform signal conditioning, scaling, linearization and conversion; can acquire measurements of temperature, pressure, flow, voltage, current; and handle multiple digital signal types broadly used in IoT and other industrial applications, such as facility monitoring, environment monitoring, and industrial process control. The new ND-6117, ND-6124, ND-6150, and ND-6160 modules feature Modbus/RTU as the best remote data transmission protocol, which provides customers a comprehensive product offering.
-
product
RS232 RS485 RS422 Serial To Ethernet Modbus Converters / Device Servers
In the past two decades, legacy serial communication protocols such as Modbus have merged rapidly with modern TCP/IP communication, yielding benefits including widely available infrastructures and greater distance, reliability, and flexibility. CommFront offers a range of industry-proven, easy-to-use serial to Ethernet converters and device servers, both hardware and software types. The applications of our serial to Ethernet converters include acting as a device server or a Modbus RTU/ASCII to Modbus TCP protocol converter; extending serial ( RS232 / RS485 / RS422 / TTL) communication distance over Ethernet network; controlling serial devices from remote Modbus TCP software or Modbus RTU master via Ethernet network; making a wide variety of M2M communication applications possible by enabling client access independent of any operating system or proprietary protocol; and converting conventional serial data network into TCP/IP network, etc.
-
product
3U OpenVPX Ethernet Switch and Multifunction I/O Board
68G5E
The 68G5E is a 3U OpenVPX board that is configured with an Ethernet Switch module (choose the ES1, 12-Port GbE Cu legacy unmanaged Ethernet Switch, or the ES2 16-Port Cu GbE managed Ethernet Switch with optional 4x 10GBASE-SR 850 nm multimode Fiber Optic interface) and provides additional support for one NAI smart I/O and Communications function module. Uniquely designed, the 68G5E provides ‘independent’ Ethernet Switch capabilities and can operate as a MFIO board end point with access via the 1 x1 PCIe and/or 1x 10/100 Ethernet motherboard Control Port which hosts the NAI Ethernet Protocol Server/Listener application for direct GbE MFIO control. Ideally suited for rugged Mil-Aero applications, the 68G5E delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems in air, land and sea applications.
-
product
8 Serial Communication Channels, Programmable RS-232/422/485 Non-Isolated
SC3
Serial Communication Module SC3 provides up to 8 high-speed, programmable RS-232, RS-422, RS-485, non-isolated communication channels. Each channel is programmable for either Serial Communications (SC) protocol or General Purpose I/O (GPIO) modes as either RS-422/485 (differential) or RS-232 (single ended) hardware level interfaces.
-
product
Data Communication Solution
BACnet/IP
BACnet is a data communication protocol mainly used in the building automation and HVAC industry (Heating Ventilation and Air-Conditioning).
-
product
LAN⇔RS-232C Conversion
SI-60
SI-60 is an interface converter to connect factory automation equipment and analyzers, which only have the RS-232C serial communication port, to LAN. The built-in Lantronix Xport® on the LAN interface converts RS-232C data into LAN protocol (TCP/IP). The device supports 35mm DIN rail and the wide range of operating temperature. Therefore, you can use it for factory automation without worry.
-
product
RFFE Protocol Analyzer and Exerciser
PGY-RFFE-EX-PD
Prodigy Technovations Pvt. Ltd.
RFFE Protocol Analyzer (PGY-RFFE-EX-PD) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. The RF Front-end control interface (RFFE) Serial bus interface is emerging as a chosen for controlling RF frond end devices. There are variety of front end devices such as Power Amplifiers (PA), Low-Nose Amplifiers (LNA), filters, switches, power management modules, antenna tuners. It is widely used in mobile devices.
-
product
Industrial Data Communications
In this section you will find hundreds of industrial-grade infrastructure, gateway and conversion products for all major data communications protocols. Amplicon can specify a solution for almost any data communications task, including transmission solutions for wireless, copper and fibre optic based links.
-
product
ARINC 664 P7 IP Core
iWave’s ARINC 664 P7 IP is an Ethernet Technology that provides a deterministic network to build an ARINC 664 P7 end system with guaranteed service to each subscriber with free access to the network. This protocol offers dedicated bandwidth for each node with guaranteed quality of service. iWave offers high integrity and redundancy management, as well as UDP/IP, profiled communication layer implemented in hardware.
-
product
Mini PCIe Expansion Kit
iDoor
Advantech’s iDoor Expansion Module is a brand-new design concept which utilizes the Mini PCIe format. iDoor modules include: communication, fieldbus protocol and digital I/O. The highly flexible customization and easy assembly provide integrated solutions to meet different needs.
-
product
UFS Protocol Analyzer
PGY-UFS3.X-PA
Prodigy Technovations Pvt. Ltd.
UFS Protocol Analyzer (PGY-UFS3.X-PA) is the Protocol Analyzer with multiple features to capture and debug communication between host and design under test. PGY-UFS3.X-PA, UFS Protocol Analyzer, value based analyzer in its class, offers capture and debug of data across MPHY, UniPro and UFS protocol layers. It allows for instantaneous decoding of UFS layer, UniPro layer and MPHY layer with flexibility to correlate decoded data across these protocol layers.
-
product
PXIe-7846, Kintex-7 160T FPGA, 500 kS/s PXI Multifunction Reconfigurable I/O Module
784143-01
Kintex-7 160T FPGA, 500 kS/s PXI Multifunction Reconfigurable I/O Module—The PXIe‑7846 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals to ensure complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PXIe‑7846 features a dedicated A/D converter (ADC) per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical data acquisition hardware. The PXIe‑7846 also includes peer-to-peer streaming for direct data transfer to other PXI Express modules.
-
product
PROFINET Gateways
The PROFINET Fieldbus gateways provide seamless communication between Modbus RTU/TCP and PROFINET communication protocols.
-
product
USB-7845, Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device
783200-02
Kintex-7 70T FPGA, 500 kS/s Multifunction Reconfigurable I/O Device - The USB‑7845 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7845 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
Linear DC Power Supply
MPS-P Series
This series of programmable DC power supply is a new generation of high-quality programmable linear DC power supply. It can display voltage, current, power and other parameters in multiple windows at the same time. The series of products is equipped with RS232 communication interface. It can be combined with other instruments arbitrarily and integrated into a test system with special functions to meet the measurement requirements in different occasions. The host computer program can be edited through the communication protocol, which brings great convenience to the user's use. It is a replacement product of ordinary programmable power supplies, has a very high cost-effective advantage.
-
product
IEC61850 Digital Substation Testing
With the development of power system, more and more digital substation based on IEC61850 has been built in the world. IEC61850 is the new communication protocol which is adopted by power system so as to change the analog complicated wiring connection and protocol conversion. Based on IEC61850, all Messages, such as GOOSE, SV, MMS, PTP, etc, could be communicated on the Ethernet via fiber optical cable connection. In China, the digital substation have started since 2003, until now there are already more than 6000 digital substation put on operation, China Power Grid is planning to build 5000 more new digital substations. PONOVO, as the leading power system testing solution provider, have launched plenty of IEC61850 digital testing tools, not only digital relay test set, but also MU test set, multi-functional analyzer, 24 hours online monitoring and analyzing system, etc so that users could have suitable testing equipment for the digital substation commissioning and testings.
-
product
IEC 61850 Testing
HAOMAI Electric Test Equipment Co., Ltd.
IEC 61850 is an international standard defining communication protocols for intelligent electronic devices at electrical substations. It is a part of the International Electrotechnical Commission's (IEC) Technical Committee 57 reference architecture for electric power systems.
-
product
Test Set
ASE2000
The ASE2000 Test Set is a full-featured protocol test unit. It provides the user with a powerful and flexible tool for diagnosing communication problems and testing and maintaining RTU and IED equipment. The test set has three modes of operation, Master Simulation, RTU Simulation, and Line Monitor.
-
product
I2C Adapter MS
LAN
*No driver necessary*Integration of communication via DLL and TCP / IP & UDP protocol possible*Open interface description enables communication without a DLL*Supports TCP / IP, UDP and DHCP
-
product
2 Channels, ARINC 568/579 Communications
AR2
The AR2 module provides an ARINC 568/579 communications interface with 2 channels. Channel 1 is Rx and Tx for ARINC 568 and channel 2 is programmable as either Rx or Tx for ARINC 579. This module only provides an interface and data management. Any specific protocol handling must be programmed by the user in the application layer.
-
product
NTDS I/O Analyzer
The NTDS I/O Analyzer provides insight and visibility, enabling users to quickly and efficiently analyze timing relationships, message protocols, throughput, and data integrity on all types of NTDS interfaces. It is capable of monitoring any combination of NTDS Parallel Type A, B, C, H and NTDS Serial Type D, E channels as defined in the MIL-STD-1397 revision B and C specifications regardless of NTDS mode. The channels are connected to existing NTDS cabling with NTDS tap boxes and extract ongoing communication. Each word of NTDS information received is time-stamped with a 125 nanosecond resolution clock ensuring highly accurate timing measurements. Data collected is stored locally for analysis and can be transmitted to external equipment enabling remote troubleshooting, event reconstruction, or time-critical feedback on system performance.
-
product
Miniature Airborne Communications Converter
MACC II - Converter
Excalibur’s MACC II represents a third option. A proven, low risk, low cost, off the shelf product that translates between different communications specifications. The MACC II can solve your communications problems without R&D costs and without schedule risks while still providing you with the flexibility to customize the system to your specific needs.The MACC II is a wholly contained Miniature Airborne Communications Converter (data converter - protocol converter or translator). The MACC II can carry up to 4 modules. Each module can be one of the following protocols: 1 dual redundant MIL-STD-1553/1760 interface1 H009 channel5 MMSI channels5 ARINC-429 channels2 ARINC-708 channels2 ARINC-717 channels5 ARINC-825 (canbus) channels2 Serial channels (RS-232/422/485, NMEA 0183)Ethernet (10/100/Gigabit)10 Discrete I/O signalsAnalog to Digital / Digital to AnalogPlease see multi protocol 8000 modules for additional information on protocols that can be used on the MACC II.
-
product
PCIe-7851, Virtex-5 LX30 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device
781102-01
Virtex-5 LX30 FPGA, 750 kS/s Multifunction Reconfigurable I/O Device - The PCIe‑7851 features a user-programmable FPGA for high performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The PCIe‑7851 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
product
TTL/I2C/SPI* Expansion Kit
OP-SB5GL
OP-SB5GL is the interface expansion kit that has a port to measure RS-232C(V.24) and a port to measure the TTL / CMOS signal level communications. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communications between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI* on monitoring and simulating.
-
product
Carrier - Virtex 7 W/FMC Site
VPF: 3U VPX
The VPF is a VPX form factor (VITA 46), FPGA processor board designed to meet the needs of challenging, embedded high‐performance digital signal processing applications at a competitive price point. AMD Virtex 7: VX330 and VX690 population options are available. The Virtex 7 FPGA provides impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed‐point and repetitive processing tasks. The VPF FPGA node processes input from the FMC HPC (Vita 57.1) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules (250MSPS to 4.0GSPS). The VPF is fully compliant with the OpenVPX standard and accommodates the PCIExpress Gen 3.0 communication protocol. Delphi also offers a VPF FPGA Design kit which allows customers to leverage and modify DEG source code, develop within an open architecture, and rapidly integrate FPGA HDL. The DEG FPGA Design kit includes: Source code, simulation test bench and utilities to support custom algorithm development. Embedded Linux, VX Works and Windows software drivers are available. HPC FMC Site, Fully Compatible with all Delphi ADC and DAC FMC Modules.
-
product
Air Data Test Calibrator
ADC-2522
The ADC-2522 is built on TestVonics ADC-2550 series platform. It is designed for rackmount use and features a large 10.4" display with resistive touchscreen. The calibrator has the ability to emulate the Sperry / Honeywell ADT-222B IEEE-488-1975 communications. This allows the calibrator to be a plug and play replacement for the aging Honeywell ADT-222B Air Data Test System and similar test sets, without the expense in having to modify existing communication protocols or software.
