-
Product
LINEAR AMPLIFIERS
F-series
-
The F-series amplifiers are designed to extend the output range of low voltage signal sources. They are general purpose devices with a very low output impedance, very fast response and high current. The output is linear from DC up to few megahertz range.
-
Product
Protable Wattmeter
ST-2000 W
-
Standard Electric Works Co., Ltd
● Principle : Electrodynamometer type● Accuracy : ±0.5% of full scale● Scale Length : Approx. 135mm(5-3/8”)● Scale Divisions : 120● Frequency Ranges : AC 25 to 1000Hz (COSØ=1.0) (suitable for DC) AC 25 to 500Hz (COSØ=0.2)
-
Product
Controllable, Programmable DC Source
LAB SMP
-
*Easiest operation via the front panel*Indication via graphic display*Constant current, voltage, resistance, power operation and simulation of PV characteristics*Creation of any voltage and current curves via memory card or digital interface (sequential control)*Voltage and current rise time (U and I slope) adjustable*Umax and Imax can be set by the user in order to limit the output voltage or current
-
Product
Power Meters
Power Meter
Teledyne Test Tools range of digital power meters are for single-phase (1P/2W) AC power measurements with a test Bandwidth ranging from DC, 0.1 Hz to 100 kHz. The T3PM1006 model features a 4” TFT LCD screen with a five-digit measurement display. It offers 19 power measurement parameters to choose from, integration measurement function, front/rear panel input terminals, and various communication interfaces to help users to make convenient and accurate power measurement. The T3PM1100 model offers DC, 0.1 Hz ~ 100 kHz test bandwidth, 16 bits ADC, and 300 kHz sampling rate. It features a 5” TFT LCD screen with a five-digit measurement display. It also has options to display waveform (voltage/current/power), the integration measurement function, harmonic measurement and analysis of each order (meeting the IEC 61000-4-7 harmonics measurement requirements at 50/60 Hz), external sensor input terminals, and various communication interfaces to help users to make convenient and accurate power measurements.
-
Product
H.V. Probe Meter
PD-40AM
-
Standard Electric Works Co., Ltd
● Measures positive polarity DC voltages up to 40kV.● Lightweight and rugged.● 2 available contact tips: round needle tip for normal use and a special flat spring-type for CRT anode.● Are typically used to measure high voltages in TV sets, power supplies and instruments in laboratories.
-
Product
Powered NIM Crate
NIM Portable 150W
-
For portable applications this transportable mini NIM crate is suited best for providing 7 NIM slots, (2½ slots used by UEP15 power supply), in a solid steel-aluminum construction. The top cover is equipped with a handle and has a side perforation for convection cooling airflow. The crate is equipped with the very compact UEP15 - 150W, slot power supply providing all 6 DC voltages.
-
Product
Pocket-Size Analog Multimeter
HH2701
-
Basic Accuracy 4.0%. 5 Functions / 13 Ranges. Voltage test up to AC500V and DC 500V. Current test up to 250mA DC. Resistance test R X 1KΩ. Test Batteries 1.5V and 9V
-
Product
Stand Alone/ Bench Top Load Cell Amplifier/ Conditioner Module
MODEL TMO-2A
-
The TMO-2A Transducer Modules is a complete differential amplifier/signal conditioners with self contained power. The unit provide excitation, balance and span adjustment via precision 10 turn pots, and shunt calibration necessary to couple a user supplied bridge type transducer to an indicating instrument. Zero to full scale output is specified at 4-20 mA. The TMO-2A provides a floating shunt calibration circuit which applies calibration at the transducer, thereby eliminating errors due to line losses. The excitation supply incorporates a Wagner Ground to greatly improve Common Mode Rejection. The factory set bandwidth of the module is narrow to improve stability. The removal of a single capacitor will increase the frequency response DC to 60K Hz for dynamic data applications.
-
Product
Field Strength Meter
DIGI-FIELD
-
Measuring radio frequency and microwave radiation has never been easier! This unit covers the amazing range of DC - 12 GHz and will give you digital readout of the relative field strength of broadcast signals such as cellular phone, microwave oven leakage, TV station, CB radios using the (1MHz - 1GHz) telescoping antenna provided.
-
Product
Battery Gauges
-
Global Digital Instruments, LLC
Our battery fuel gauges and LED volt meters are designed to monitor the charge capacity of DC powered equipment and monitor information about the equipment's electrical system.
-
Product
LISN Line Impedance Stabilisation Networks / AMN Artificial Mains Network
-
A LISN Line Impedance Stabilization Networks / AMN Artificial Mains Network: *supplies the neccessary mains voltage (AC or DC) and current for the Equipment under Test (EuT).*couples interference voltage generated by the EuT and supplies it to the receiver.*provides well defined RF-impedance to the Equipment under Test (EuT)*keeps away unwanted disturbance coming from mains (filter)*protects the mains from unwanted disturbance voltage generated by the EuT
-
Product
Low-Thermal EMF LXI Matrices
-
Pickering low-thermal EMF LXI matrices offer excellent thermal stability and substantially reduced thermal EMF figures when compared to a conventional switching matrix. Typical applications include signal routing in automatic test equipment, selecting thermocouple inputs, switching amplifier gain circuits and high accuracy DC microvolt measurements.
-
Product
120W Power Supply, 15V, 7A or 30V, 4A
E3632A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The single output, 120-200 W, GPIB, E3632A-E3634A provide dual range outputs; small, compact size for bench use; low output ripple and noise; as well as built-in measurements and basic programmable features with GPIB and RS232 interface. The Keysight 120W, GPIB, single output E3632A is a high performance supply optimized for manual and basic automated testing; and, with a combination of benchtop capabilities and system features, it is designed to help improve measurement quality and reduce test time.
-
Product
Angle Position On-Axis
-
The magnetic rotary position sensor product family detects the absolute angular orientation of an on-axis two-pole magnet rotating over the center of the IC. The absolute angular position can be provided in various formats, including PWM, ABI and UVW, or directly read through the host interface. According to the application’s requirements, resolutions from 8-bit up to 14-bit are available. This technology can be employed in high-accuracy angle position detection, high-speed rotation systems and brushless DC motor control. Any rotary magnetic position sensor can replace either absolute or incremental optical sensors, other magnetic and inductive technologies, potentiometers or magnetic switches.
-
Product
MMI-CI
100694
-
For fixtures with higher voltages, the MMI-CI is a good basis. The MMI-CI is made of NON-dissipative plate material and can therefore be used in the low-voltage range (up to 1000V AC/ 1500V DC). The earthing package included is an important component. This is because the housing earthing, the earthing connection and also the earthing test ensure that the safety standards are met. The solenoid interlock and the safety switch ensure access protection.
-
Product
Super high temperature hall effect measurement system
-
Super high temperature hall effect measurement system that is useful to flow gas into chamber with sample. - Newly developed furnace that makes it possible to increase over 800 and use for measuring hall effect. - Gas flow control system in order to flow various gas. - Sample holder for high temperature. (keep the good contact on 800) - High Temperature control system (DC power) On condition of specific temperature with gas flow , new semiconductor materials have been developed to see electrical property's change.
-
Product
PXI General Purpose 2A Relay Module 32xSPST
40-132-201
Relay
Pickering Interfaces 40-131/132 modules are a range of low cost, general purpose electromechanical relay cards. They are capable of switching voltages up to 300VDC/250VAC and current up to 2A. They are suitable for use where reed relay based switching cards do not have sufficient voltage or current carrying capability. Applications include the switching of medium power AC and DC loads, or slave switching larger relays, contactors or solenoids. Connections are made to the card via a front panel mounted 78 pin D-Type connector plug.
-
Product
Saturable Reactor Inductors
-
Osborne Saturable Reactors are designed to provide a variable output voltage through the use of variable impedance connected in series with a constant impedance load. Each saturable reactor’s impedance is determined by the application of DC power to a control winding. As the level of power supplied to the control winding is increased, the saturable reactor becomes more saturated. This reduces the impedance of the AC gate winding, and increase the amount of the supply voltage that is transferred to the load. Conversely, as the power is reduced to the control winding, the reactor becomes less saturated, the gate winding has more impedance and less of the input voltage is provided to the output impedance. This approach provides excellent quality, reliability, and control when designed to match the requirements of a specific application.
-
Product
Adapter, 2.4 mm (m) to 2.4 mm (m), DC to 50 GHz
11900A
Coax Adapter
The Keysight 11900A is a metrology-grade, 2.4 mm male to 2.4 mm male adapter with dc to 50 GHz operation.
-
Product
PXI Bus Signal Amplifier
3222
Amplifier
Model 3222 is a 3U single-slot, PXI-based power amplifier designed for signal amplification. Offering unmatched signal purity, Model 3222 amplifies signals from dc to over 20 MHz. The unit has a fixed gain of x10, however, the same amplifier is available with custom gain, with no signal purity or performance degradation.
-
Product
Multi-Channel, 14-Bit Digitizer
ADQ14
Digitizer
ADQ14 is a 14-bit digitizer family with 1, 2, or 4 channels and 0.5, 1, or 2 GSPS sampling rate. It is also available with either AC or DC coupling (ADQ14AC and ADQ14DC) and comes in six different form factors. This simplifies integration and enables cost-efficient system-level design.
-
Product
Charge/Discharge System Controller
PFX2500 Series
-
PFX2500 Series is a high performance Charge/Discharge system controller that takes measurements in combination with our DC power supply and electronic load in order to evaluate test sample (electric storage elements such as secondary batteries) characteristics. It is also capable to perform evaluation test with high-performance, large capacity and wide range of rating with the combination of DC power supply and electronic load.Execution of the test is conducted by the exclusive application software. The test corresponds to long time continuous test and synchronization test with temperature chambers with the multiplexed protection performance. In addition, easy data editing is also capable with fulfilling graphic performance.
-
Product
Adapter, 2.4 mm (m) to 3.5 mm (m), DC to 26.5 GHz
11901A
Coax Adapter
The Keysight 11901A is a 2.4 mm male to 3.5 mm male metrology-grade adapter with dc to 26.5 GHz operation.
-
Product
High Voltage Amplifier
HA-800
-
*800Vp-p(±400V DC) *70mAp-p(±35mA DC) *Bandwidth: ≦200KHz(400Vp-p) *Slew Rate: 200V/us *Gain(AMPL): 0~180(10 Turn VR) *DC Offset: ≦0~±400V (10 Turn VR + SW) *Output Resistor: 100*Ω
-
Product
Fanless Embedded System With Intel® Celeron® Processor N3160, VGA, HDMI, 4 COM, 2 GbE LAN, 4 USB, 2 PCI Express Mini Card Slots And 9 To 36 VDC
eBOX626-853-FL
-
The eBOX626-853-FL is a slim-type fanless embedded system with wide range temperature and wide range DC input support. The cost effective compact embedded box PC is designed to support the Intel® Celeron® processor quad-core N3160 (codename: Braswell) integrated with Intel® Gen 8 graphics and DirectX 11.1. One DDR3L 1333/1600 SO-DIMM socket supports up to 8 GB memory. The IP40-rated industrial computer eBOX626-853-FL combines low power consumption with high performance graphics and computing for smart automation, transportation, industrial gateway, multiple media kiosk and other IoT&M2M applications.
-
Product
Fast Precision D/A Converters
-
For test and measurement, and HIL applications demanding both dc and ac performance, our fast precision D/A converters (DACs) enable higher speed waveform generation of up to 12.5 MSPS with 4 × oversampling with clean signal spectrums.
-
Product
RF Power Transistors
Silicon MOSFET
-
Macom Technology Solutions Holdings Inc.
At MACOM we offer a broad range of silicon bipolar transistor products designed for applications ranging from DC to 3.5 GHz. Our silicon bipolar transistors are ideal for civil avionics, communications, networks, radar, and industrial, scientific, and medical applications. Our all-gold metallization fabrication processes ensure high performance and long term reliability for ground and space applications.
-
Product
AC Reference Generators
SR21
-
Computer Conversions Corporation
The SR Series are miniature, low cost AC reference generators designed to supply 26 or 115 volt excitation to synchros or resolvers in military and industrial control applications. They accept +/-15V DC and provide up to 5VA of transformer isolated output power. These converters are packaged in PC card mounting modules 2.6”x3.1”x1”H.
-
Product
Manual Step Attenuator, DC to 4 GHz, 0 to 70 dB, 10 dB steps
8495A
Attenuator
The Keysight 8495A dc to 4 GHz manual step attenuator offers exceptional repeatability and reliability. Attenuation is provided in 10 dB steps from 0 to 70 dB. Precision gold-plated leaf springs ensure long life (over 5 million cycles) and very high attenuator repeatability (typically 0.01 dB). To improve measurement accuracy, NIST traceable data (SWR and attenuation) is available as Option UK6. Custom step attenuator/switch combinations are possible. The Keysight 11716A/B/C interconnect kits provide quick connection of Keysight 8494/5/6/7 1 dB and 10 dB step attenuators in series for greater dynamic range with 1 dB steps.
-
Product
High Voltage EMC Surge Generator
TM510
-
TM510 Surge Generator is mainly used for testing power cable high-resistance and arc-over fault whose grade range is 0-10kV, co-operating with cable fault tester and locating devices to test and locate faults. If the user choose the professional digital milli-ampere-meter, as for cable with grade range about 0- 6kV, the instrument can also be used to do DC&voltage resistance test and current leakage test after the fault is repaired. The instrument is internally equipped with voltage-rise rectifying and discharging device, has complete functions, and is also convenient and safe to be wired and operated.
