Serial
a bus that can be used with almost any device transmitting a single stream of data.
See Also: Bus, Parallel, I2C, LIN, Can bus, ExpressCard, Fieldbus, FireWire, RS-232, RS-485, PCI Express, Serial ATA, Serial Peripheral Interface, SMBus, Serial Analyzers, Serial Digital Interfaces, Serial Communications, Serial Data
-
product
LAN⇔RS-422/RS-485 Conversion
SI-65A
SI-65A is an interface converter to connect factory automation equipment and analyzers, which only have the serial communication ports for RS-422/485, to LAN.
-
product
Interface
P-SER
P-SER I/O product is a native PMC form factor interface providing real-time serial input and output with high time-precision reception/input time-stamping, scheduled transmission/output, event triggering and interrupt support. This interface is designed to meet the needs of both the simulations/test and the real-time embedded applications whether in Windows or VxWorks environments.
-
product
OEM Gas (NO) Analyzer
BE-220FSD
The BE-220FDS is an OEM NDIR detector for measuring NO in automotive emission gases. The BE-220FSD can output NO concentration by digital data and analog voltage. In addition, it can be connected with the HORIBA BE-150 bench by serial line and relay the commands for BE-150. The BE-220FSD meets OIML Class 0 and complies BAR-97 & GB18285-2018 specifications.
-
product
VXS 21 Slot
The Comtel VXS Backplane 21 slots match performance and cost-effectiveness by realising a fully optimised signal and power distribution environment. Design techniques ensure uniform impedance controlled signaling environment and ground guarding minimises line-to-line crosstalkThe VXS provides the high-speed switched serial performance of VITA 41, hybrid design includes VXS payload slots, VXS switch slots and conventional VME64x slots, The 21 slot VXS backplanes supports data rates well beyond 3.125Gb/s per link. As a dual-star design, it can be operated with two switch boards, allowing addressing of both link ports on payload cards.
-
product
Becker Transponder Test Fixture
TA-3400
This transponder test fixture is specific to the requirements for testing Becker Avionics Transponders and provides interface connectors for both the panel mount and remote systems. The panel also provides switches to implement Gillham code altitude as well as separate interfaces for an external parallel or serial encoder. The panel will interface with the RMU 5000 or standard control head. This fixture also comes with voltage and current meters along with an internal dimming source. This panel comes in the standard 19 inch rack width and measures 12 inches in depth.
-
product
Mixed Signal Oscilloscope: 200 MHz, 2 Analog Plus 8 Digital Channels
MSOX2022A
200 MHz2 analog plus 8 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
product
In-System Programmer for AVR
MPQ-AVR
Supports Atmel AT90, ATtiny, ATmega, ATxmega device families Supports JTAG, SPI and PDI programming interfaces Field Upgradeable - always supporting the latest devices Secure image management - protects your IP In-circuit gang programming of up to four devices at once Can be deployed in arrays to program up to 64 devices in parallel Stand-alone, PC-controlled or ATE-controlled operation Automatic device serialization
-
product
Multibus Ethernet Card
MS 1750
- Processor: LPC3250 processor with ARM 9 core running at 266 MHz- SDRAM Memory: DDR2 256 MB (scalable to 512 MB)- Flash Memory: NAND flash 512 MB- Display & Graphics: Programmable color LCD controller supports up to a TFT interface- Touch screen: Integrated touch screen controller- Network Support: 10/100 Base-T Ethernet PHY- PC Interface: One USB 2.0 high-speed On-the-Go interface- Multibus Interface- Serial Interfaces: Up to four external UARTs- CAN 2.0B controller- Three I2C ports- Three SPI ports- GPIO: Programmable I/O depending on peripheral requirements
-
product
Digital I/O
Curtiss-Wright Defense Solutions
Curtiss-Wright Digitial I/O cards include interfaces to LVDS, Camera Link, Serial intrefaces, CANbus and customizable I/O. With over 20 years experience in the design and production of top quality COTS signal acquisition hardware, we deilver PMC, XMC and PC/104 modules that can cope with the toughest operating environments.
-
product
Optical Identification
Application areas of the 1D/2D code reader range from product tracking and product control to product identification.The sensor can read 1D and 2D codes regardless of their position. Even if up to 25% of the code information becomes damaged or soiled, it is still read correctly. The reader can also be used for optical character recognition (OCR), e.g. in order to identify products based on type labels or serial numbers.
-
product
PCI Mezzanine Card
PNIC1G
Each Ethernet interface supports 10, 100 and 1000 Mbits transmission rates with auto-negotiation for full duplex operation; 10 and 100 Mbit/s transmissions for half duplex operation, and is equipped with a 32 Kbit Serial EEPROM.
-
product
GPIB-RS232, GPIB-RS232, Instrument Control Device - North America 240VAC
779732-05
The GPIB‑RS232 is an IEEE 488 controller device for computers with an RS232 port. You can use this device to integrate an instrument into your system using GPIB. This device transforms a computer with an RS232 serial port into a talker, listener, or controller on the GPIB bus. It can also interface RS232 instruments and peripherals to the GPIB bus. It can implement the physical and electrical specifications of the IEEE 488 and RS232 standards, as well as interpret and execute high-level commands from the serial port, including RS232‑to‑GPIB and GPIB‑to‑RS232 protocol conversions. This device is IEEE 488.2 compatible. The device includes a license for the NI‑488.2 driver software, providing maximum reliability for connecting to third-party instruments with GPIB.
-
product
3-CH RTD Input Module
ND-6013
ADLINK's NuDAM data acquisition modules make up a total acquisition network and control system. Up to 256 NuDAM modules an be romotely controlled on any RS-485 network from a host computer, via a single serial RS-232, allowing communication from as far as 4000 feet from the host. Based on the RS-485 multi-drop network system, each module has a unique address ID, whereby simple ASCII command & response protocols through the standard RS-485 interface can control all the NuDAM modules in the RS-485 network. The NuDAM modules provide direct communications with a wide variety of sensors, perform all signal conditioning, scaling, linearization and conversion, and can acquire measurements of temperature, pressure, flow, voltage, current, and multiple digital signal types.
-
product
USB to Serial Converters, Hubs and Isolators
B B SmartWorx powered by Advantech USB products provide plug and play convenience with industrial ruggedness. Look for the orange connector -- you'll find a high retention port that's 50% stronger than a conventional USB port. It won't let go until you want it too.
-
product
Communication Converter
F485
The F485 is a self-contained device for converting between RS232, RS485 and fiber optic signals. The F485 is electrically isolated to improve communications in noisy environments. The converter uses internal switches to select the signal conversion type and communication rates up to 57600 bps. The F485 converter uses the data on the serial ports to determine direction and therefore requires no hardware handshaking signals from the computer.
-
product
Programmable RS-232, IR, and I/O Controller
HR-4P
The Model HR-4P is a programmable RS-232 device designed for control & automation of a Projector, LCD, or any other device with serial or IR port.
-
product
6U VPX FPGA Cards
Curtiss-Wright Defense Solutions
FPGAs have revolutionized the way digital signal processing (DSP) subsystems are configured. With a large number of gates, hardware multipliers, and high-speed serial interfaces, FPGAs enable sophisticated applications, including radar, signal intelligence, and image processing, which rely on repetitive processing that can be expressed in highly parallel form. FPGAs perform exceptionally well in FFTs, pulse compression, filters, and digital up/down converters.
-
product
PMC Module
PMC-SCC04-IO
The PMC-SCC04-IO module is a Quad Channel serial communication controller with 64 Byte Fifo per line. The PMC-SCC04-IO is based on the XR17D154. The device support autoconfiguration registers for plug-and-play installation. This module provide 4 Asynchronous ports up to 6.125MBps .
-
product
iRobot Nodes
NITOS team has made mobile nodes using "iRobot Create" with a custom designed tray to hold the system board. The board is an "Alix Board" of "PC Engines" company . Commands are sent to the robot over a serial port and the whole system is powered from the robot's battery. The upward facing camera is used to recognise specific patterns on the ceiling, which help the robot navigate around the room.
-
product
Signal Converters For High-accuracy Angular Measurement
EIB 1500 series
*Interpolation and digitizing electronics for the real-time digital processing of positions from two scanning heads*Input: incremental rotatory HEIDENHAIN encoder with two scanning heads and distance-coded reference marks (relative orientation of scanning heads: 180° ± 5°)*Output: EnDat 2.2, Fanuc Serial Interface, Mitsubishi high speed serial interface*Integrated subdivision: 16 384-fold
-
product
cRIO-9064, 667 MHz Dual-Core CPU, 512 MB DRAM, 1 GB Storage, and Zynq-7020 FPGA, 4-Slot CompactRIO Controller
783831-01
667 MHz Dual-Core CPU, 512 MB DRAM, 1 GB Storage, and Zynq-7020 FPGA, 4-Slot CompactRIO Controller - The cRIO-9064 is a rugged, fanless, embedded controller that you can use for advanced control and monitoring applications. This software-designed controller features an FPGA, a real-time processor running the NI Linux Real-Time OS, and embedded user interface capability. Additionally, the cRIO-9064 features an SDHC slot and a variety of connectivity ports, including two tri-speed RJ-45 Gigabit Ethernet, one USB host, one USB device, and one RS-232 serial. The registered trademark Linux® is used pursuant to a sublicense from LMI, the exclusive licensee of Linus Torvalds, owner of the mark on a worldwide basis.
-
product
Quad Serial FPDP Interface with Virtex-6 FPGA - XMC
Model 71611
- Complete Serial FPDP solution- Fully compliant with VITA 17.1 specification- Up to 2 GB of DDR3 SDRAM- PCI Express interface up to x8- LVDS connections to the Virtex-6 FPGA for custom I/O
-
product
PXIe-1487, 8 Input, 8 Output, or 4 Input/4 Output PXI FlexRIO GMSL™ Interface Module
787457-01
The PXIe-1487 combines the Maxim Integrated Gigabit Multimedia Serial Link™ (GMSL™) interface with the Xilinx FPGA for high-throughput vision and imaging applications. This module provides a high-speed digital interface for using and testing modern advanced driver assistance systems (ADAS) and autonomous drive (AD) camera sensors and electronic control units (ECUs). Additionally, the PXIe-1487 makes use of a combination of GMSL™ serializers and deserializers with a Xilinx FPGA to provide a high-throughput and customizable GMSL™ interface on PXI. The included FlexRIO driver, with LabVIEW FPGA examples, provides access and control for power-over-coax, I²C back-channel communication, and general-purpose input/output (GPIO) communication on the GMSL™ channels. The PXIe-1487 is ideal for applications such as in-vehicle data logging, lab-based playback, or hardware-in-the-loop (HIL). GMSL is a trademark of Maxim Integrated Products, Inc.
-
product
64-Channel Boundary Scan Digital I/O Scan Module
JT 2111/MPV DIOS DIN
The JT 2111/MPV is a 64 channel boundary-scan digital I/O scan module enclosed in an impact resistant housing. The module is designed to test and control edge connectors, on-board connectors and logic clusters in boundary-scan applications. Multiple modules can be connected serially to increase the number of I/Os. Available with 96-pin DIN 41612 connectors and 20-pin 0.1″ pitch IDC connectors.This JT2111/MPV DIOS module is also available through our webshop.
-
product
Rugged Railway Solutions
ADLINK is a leading provider of building blocks and intelligent platforms for edge computing. Our Rugged by Design CompactPCI/CompactPCI Serial, computer-on-modules, industrial-grade system and panel computer product portfolio has been specifically selected for onboard ATO/DMI and wayside CTC/RBC/TSRS railway solutions. ADLINK’s exceptional flexibility in design and manufacturing has been utilized by top rail signaling providers worldwide.
-
product
High Resolution USB Programmable Digital Attenuator 200 to 6,000 MHz
LDA-906V Lab Brick®
The Lab Brick LDA series of Digital Attenuators bring affordability, functionality, reliability and simplicity to the microwave test bench. The LDA products range from 6 MHz to 20 GHz with input level tolerance to 2 Watts and step size as small as 0.1 dB. Lab Bricks use a native USB HID interface to avoid the difficulties inherent in using older serial or IEEE-488 interfaces implemented over USB. As a result, Lab Brick users can get to work faster without having to install kernel level drivers, and Lab Brick devices can be easily used on any system that supports USB HID devices, including low cost embedded computers using Linux or similar operating systems.
-
product
3.4 MP GMSL Camera (supports Upto 15 Meters)
NileCAM30_USB
NileCAM30_USB is the four board solution containing the camera module, serializer, deserializer and USB base board. This camera is based on AR0330 CMOS image sensor from ON Semiconductor®, with USB 3.1 Gen 1 interface. The NileCAM30_USB comes with 15 meters coaxial cable with FAKRA connector at both ends of serializer/deserializer board. The NileCAM30_USB has an S-mount (M12) lens holder which allows customers to choose and use the lens according to their application requirement.
-
product
Static Load Cells (500 N to 600 kN)
2580 Series
The Instron 2580 Series static load cells are high-precision force transducers optimized for use with 5900 and 6800 Series universal testing systems, capable of measuring loads across a wide range (up to ±600 kN) with accuracy to 0.5 % of reading and sensitivity down to 1/1000th of full scale. Temperature-compensated and calibrated on equipment traceable to international standards, they have automatic recognition with an electronic serial number and support electronic calibration, while offering overload protection (up to 150 % without damage, 300 % without mechanical failure). The 2580’s design delivers high stiffness and reliable alignment under load—making it a robust choice for tension, compression, cyclic, and reverse stress testing in materials and components.
-
product
16-Channel 250 MHz A/D with Multiband DDC, Kintex UltraScale FPGA - 6U VPX
Model 58132
- Jade Xilinx Kintex UltraScale FPGA Products and Navigator Design Suite Software Video- Jade Xilinx Kintex UltraScale FPGA Family Brochure- Complete radar and software radio interface solution- Supports Xilinx Kintex UltraScale FPGAs- 16 250 MHz 16-bit A/Ds- 16 wideband DDCs (digital downconverters)- 128 multiband DDCs- 10 GB of DDR4 SDRAM- Sample clock synchronization to an external system reference- LVPECL clock/sync bus for multiboard synchronization- PCI Express (Gen. 1, 2, &3) interface up to x8- Optional LVDS and gigabit serial connections to the FPGA for custom I/O- Ruggedized and conduction-cooled versions available
-
product
Capacitive to Digital and Touch Screen Controllers
Are 12-bit successive approximation analog-to-digital converters (SAR ADCs) with a synchronous serial interface and low on-resistance switches for driving 4-wire resistive touch screens.
