Fibre
cylindrical dielectric waveguide, which transmits light through total internal refraction.
See Also: Fiber, Fiber Optic
-
Product
Signal Transporter E/O - O/E Converter pair
LTX-5515
-
The LTX-5515 enables the precise conveyance of one analog channel plus four digital channels of information over fibre optic links ranging from metres to more than 10 kilometres. Incoming analogue data is digitised to 12-bit precision at 100 megasamples per second and transmitted over optical fiber at one giga-bit per second.?
-
Product
Optical Probes - Low Bandwidth
-
Depend on Tektronix to provide you with performance you can count on, and industry-leading service and support.*Broad Wavelength Response 500 to 950 nm or 1100 to 1700 nm*High-bandwidth DC up to 1.2 GHz*High Gain 1 V/mW*Low Noise <11 pW/√Hz*Probe Connects to DPO7000*1 and DPO/DSA/MSO70000*2Series*SONET/SDH and Fibre Channel Reference Receiver Performance
-
Product
Optical Transimpedance Amplifiers
-
Analog Devices optical transimpedance amplifiers offer a complete, high performance, single chip solution for converting photodiode current into a differential voltage input. Supporting data rates from 155 Mbps to 11.1 Gbps, our transimpedance amplifiers are ideally suited for data communications and telecommunications applications supporting lay protocols including 1×, 2×, 4×, and 8× Fibre Channel, 10GBASE-LX4, SONET/SDH up to OC-192 with FEC, and 10 Gigabit Ethernet. Our transimpedance amplifiers feature low input referred noise current, high input current, and low power dissipation.
-
Product
Dual Port Fibre Channel End-System Module for PCI Express
PCIe-FC4-NIC
-
Avionics Interface Technologies
Dual port module, operates as a Fibre Channel network node with support for multiple upper layer protocols.
-
Product
O/E Converter
TIA-4000
-
The TIA-4000 is comprised of a fibre coupled InGaAs APD detector combined with a variable reverse bias voltage network and fast transimpedance amplifier. The output of the unit is brought out to a type K female SMA connector. Light falling on the detector generates a positive-going proportional current. This current, multiplied by the transimpedance produces a voltage that is proportional to the light incident on the detector surface.
-
Product
Optical signal transmission
Bus systems
-
Allows for the transmission of high speed CAN signals via optical fibre cables during EMC tests or when there are great potential differences (high voltage).
-
Product
PXI Triple 2 Channel Fibre Optic MU
40-855-332
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
HS1760/MIL-STD-1760E XMC Network Interface Controller
XMC-1760-NIC-FP
-
Avionics Interface Technologies
Configuration Variants available: XMC-HS1760-NCNT: One NC Node and One NT Node, XMC-HS1760-NCNC: Two NC Nodes, XMC-HS1760-NTNT: Two NT Nodes - SAE AS5653-Compliant Network Controller/Network Terminal NIC - Unsolicited data path for handling Fibre Channel link service or non‐FC-AE‐1553 traffic - Supports DMA for high speed streaming of data75 Ohm single‐ended or 150 Ohm Differential coax interface – TNC connectors - Each port supports 1.0625 Gbps speed - ANSI C API interface for both NC and NT - Device driver support: Windows, Linux, & VxWorks - Quad (4) port board available on request
-
Product
Ethernet and Fibre Channel Test Platform
SierraNet M648
Test Platform
The SierraNet M648 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M648 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M648 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
Product
PXI Single 2 Channel Fibre Optic MU
40-855-312
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Utility Detection Radar
DS2000
-
There’s a lot going on underground that you need to know about before you ever start to dig. The Leica DS2000 Utility Detection Radar finds all potential threats, including non-conductive pipes and fibre optics, increasing safety by lowering the risk of accidently hitting underground assets. Increase safety, speed up work and lower asset management costs with the ability to prevent hazardous outages and collect more information. The DS2000 betters your business by making it safer, faster and more efficient.
-
Product
Comb Generator
RefRad X
-
A comb generator is built inside a conical antenna element. Therefore no cable between antenna and generator is required. Thus leads to repeatable measurement results and reliable simulation of radiation performance.Optionally a fibre link for synchronisation with the receiver is used.Frequency Range 10 kHz - 3 GHzFrequency Spacing 10 kHz, 1 MHz, 5 MHz
-
Product
PXI Single 2 x 2 Fibre Optic (M Mode) ST M50
40-860-512-M50
Switch Module
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Strain sensors
SG-01
-
The Strain Gage SG-01 is the fibre optic equivalent of an electrical strain gage. The Strain Gage SG-01 can be mounted directly on the surface of a structure by means of an adhesive. In this way, the fibre sensor makes direct contact with the surface and therefore measures directly the strain at the surface.
-
Product
Up to 3.2GHz, DB9 Male Fibre Channel Loopback Tester
F9M-LPBK
-
This premium loopback tester support speed of up to 3.2GHz and certified to pass the eye-pattern test.
-
Product
635nm Visible Light Source
VLS-40
-
The KD Optics VLS-40 is an easy to use, hand-held, visible source used for testing fibre optic cable installations. It is especially useful when testing fibre optic cables close to the terminal equipment. The unit is pocket sized with a long battery life, making it ideal for local fault finding and continuity checking of fibres.
-
Product
Textile Test Equipment
-
AVENO textile testing equipment including fabric tester, yarn tester, fibre tester, related abrasion tester, color fastness tester, strength tester, flammability tester, snag tester, pilling tester, and more. Mainly used to check the quality of textile products.
-
Product
PXI Single 2 x 2 Fibre Optic Mux MU
40-860-312
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
Next Generation Subsea Inertial Navigation Systems
TOGSINS
-
The new TOGSINS builds on core TSS fibre optic gyro technology by incorporating inertial navigation (INS) capability. As with TOGS, it is available in three standard heading accuracy variants: 0.1° (TOGSINS1), 0.3° (TOGSINS3) and 0.5° (TOGSINS5), all rated for operational depths to 4,000m or 6,000m giving you a range for all your needs.Inertial position data is produced using an INS algorithm, within the firmware framework of TOGS, whilst attitude data is delivered via accurate roll/pitch measurement of 0.01° (TOGSINS1) and 0.05° (TOGSINS3 and TOGSINS5), and a heave performance of 5cm or 5%.
-
Product
"Signal Transporter"
LTX-5510
-
The LTX-5510 enables precise conveyance of analogue plus four channels of digital information over fibre optic links ranging from meters to more than 10 kilometers. Incoming analogue data is digitised to 12-bit precision at 50 mega-samples per second and transmitted over optical fibre at a 1 Gb/s data rate.?
-
Product
Avionics Network Simulation Systems
-
Avionics Interface Technologies
Support for up to 30 Network Interfaces (Fibre Channel & Ethernet)Time Synchronization with IRIG-B & IEEE 1588 Master ClocksFull Data Capture with time stampingData simulation with precise timing & synchronizationNetwork data replay from previously captured trafficPerform Network analysis using AIT's intuitive, easy to use, Ethernet & Fibre Channel simulation tools
-
Product
System Analyzer
H60
-
A meter conceived for professionals that know what they want. Functions for CATV systems, MATV systems and IRS systems done in coax or fibre. For free to air or encrypted programs, the H60 features unprecedented capacities for a meter of this size. There is simply no possible comparison with others, Capacity to measure any wanted signal or interference up to 3,3 GHz. The best way to analyze the TV or telephony (GSM or LTE/4G) equipment or installations.
-
Product
Fibre Channel Data Playback
RMSR-2002-PS
-
Curtiss-Wright Defense Solutions
The TTC RMSR-2002-PS playback unit houses two data cartridges. Data is read through the Fibre Channel Interface. Front panel indicator LEDs show Active, Lock and Fault status for each cartridge.
-
Product
Inspection Microscope
-
This compact, lightweight and ergonomic Inspection Microscope is specifically designed for inspecting ferrule and fibre end faces in the field or the laboratory. The microscope provides dual-illumination, both coaxial and oblique; to produce the highest-quality image detail and superior view of fibre end face cleanliness and core condition.
-
Product
Launch Fiber Box
-
OTDR measuring devices are used in various ways in fibre optic technology. They enable extensive characterisation of existing fibre optic cabling networks. The use of launch and receive fibres is advantageous when it comes to ensuring precise results evaluations. With bidirectional backscatter measurements with launch and receive fibres, the attenuation values of the first and last plug-in connection can be determined precisely by averaging and device dead zones can be avoided. Measuring device manufacturers recommend different lengths of launch and receives fibres to avoid “phantom reflections”. These launch and receive fibres are also subject to measuring equipment monitoring and should regularly undergo revision in accordance with the OTDR measuring devices. A good measurement result depends on the state and quality of the measuring equipment used. Diamond offers various types of launch and receive fibres, one with standard telecommunications connectors and the other with an outdoor connector for harsh environments.
-
Product
High-Speed Digital Switch Matrix & Optical Power Management System
VERTA
-
Avionics Interface Technologies
Switching & Optical Power Management system supporting Fibre Channel & Ethernet interconnect and power management applications.
-
Product
PXI Quad 2 x 2 Fibre Optic Mux LC
40-860-442
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PCIe 4.0 Protocol Analyzer
Summit T48
Protocol Analyzer
Teledyne LeCroy’s Summit™ T48 joins the Summit™ T416 as the second protocol analyzer to be released in its family of tools supporting the PCIe 4.0 architecture. The new Summit™ T48 protocol analyzer based on the PCIe 4.0 specification supports up to 16GT/s and up to x8 lane width for protocol analysis. Companies that are interested in testing PCIe 4.0 based I/O cards such as Storage Controllers, Ethernet, Fibre Channel, Infiniband, and others will now be able to get all of the protocol analyzer debugging features they need, while being able to better manage their costs. SSD storage applications will also benefit from the integrated support for SSD bus protocols such as PCIe/ NVMe/ SMBus/ NVMe-MI/ TCG and others. When combined with Teledyne LeCroy’s Summit™ Z416 protocol exerciser, the Summit™ T48 will provide a deeper understanding of test results on a variety of test configurations. Teledyne LeCroy’s wide range of high speed interposers and probes provide full flexibility and connectivity to CEM and other form factor sockets on system boards as well as solder down and mid-bus probes.
-
Product
PXI Single 2 Channel Fibre Optic SC/PC
40-855-212
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
-
Product
PXI Dual 2 x 2 Fibre Optic Mux SC/PC
40-860-222
Fiber Optic Switch
Pickering PXI Fiber Optic MEMS Switching cards are available in many high density formats with a choice of 5 different connector styles to suit most applications: FC/APC (for optimal performance), FC/PC and SC/PC for general applications and LC and MU for high density applications. Fiber optic multiplexers create a signal path by redirecting the optical signal into a selected output fiber. This is achieved using Micro-Mechanical Mirrors driven by a highly precise mechanism and activated via an electrical control signal.
