-
Product
Bench/System DC Power Supply With PowerFlex Or PowerFlex+ Regulation
QPX Series
-
Wide range of voltage/current combinationsUp to 80V and up to 50A within the same power envelopeLow output ripple and noise of <3mV rms at full powerHigh setting resolution of 1mVAnalogue control interfaces for voltage and currentBench or rack mounting, front and rear terminalsUSB and LAN (LXI) interfaces with GPIB optional (QPX600DP, QPX1200SP and QPX750SP)
-
Product
Multi GPU Cluster
SKU-078-XX
-
- Easy Plug-and-Play installation- Open-chassis concept- Can accommodate up-to 4 high-performance x16 PCIe GPU boards- Supports 1-slot, 2-slot, and 3-slot-wide PCIe GPU boards- Unique placement of x16 PCIe GPU boards for efficient air cooling (Patent pending)- Connects to the host computer via PCIe cable and PCIe/MiniPCIe/ExpressCard(R) host board- Compliant with PCIe Specification 2.2 (Gen 2) with 5 Gbit/sec unidirectional bandwidth- Powered from dedicated standard ATX power supplySupports multiple ATX psu per cluster- Up to four PCIe Clusters per one PCIe host board- RoHS-compliant
-
Product
Screw-Terminal & Power Adapter Board - DC-coaxial-jack connectivity for 1 or 2 External VDC Power Supplies
TE3202
-
- Provides DC-coaxial-jack connectivity for 1 or 2 external 48 VDC power supplies- Provides screw-terminal connectivity for all sense, return, & output lines- May be directly connected to the HD-DB15 on the TE3200 front panel, or extended with a standard VGA extension cable.- Provided header pins for jumpering sense & return lines to channel output & return lines.- Provides a 2-pin header for jumper configuration with only one externally supplied 48VDC input (but, halves the maximum output current)
-
Product
Software for VME Power Supply Modules
V65XX
-
V65XX Controller – Control Software for VME Power Supply Modules is a console application that allows a complete and friendly management of a single CAEN VME High Voltage Power Supply board (V65XX series), controlled via CAEN VME Bridges.
-
Product
Basic Quad K-Type Analog Thermocouple Amplifier
SEN-30103-K0
-
Analog thermocouple amplifier board based on the AD849x from Analog Devices (successor of the AD597). This quad-channel thermocouple board converts the very low voltage signal from a thermocouple to a highly-linear, 0.005V/C output with either 0V or 1.245V offset (both configurations stocked) while removing unwanted noise from the signal. Many supply and output configurations are available with this board, though the PCB was designed with Arduino in mind. Specifically, the output header will plug directly into a standard Arduino Uno or Mega, with a pin-for-pin match for power supply, ground and analog outputs. With a 5V Arduino, temperatures from 0C to 1,000C are possible with the 0V offset board and -249C to 750C with the 1.245V offset board. If using a 3.3V microcontroller (Due, etc), the board must be supplied with no more than 3.3V to avoid damaging the microcontroller. Temperature measurement range is dependent on the supply voltage. It is possible to supply the board with higher voltages to allow temperature measurement over the entire operating range of the K-Type and J-Type thermocouples, allowing use with more capable data acquisition equipment.
-
Product
PXI Prototyping Module, 1-Slot, Dual 20-Pin GMCT
40-225A-811
Prototyping Module
The 40-225A PXI Prototyping Modules are stripped down versions of the 40-220A PXI Breadboard series. These are very basic, low cost prototype modules. They have no PXI interface but do have access to fused power supplies from the PXI backplane.
-
Product
Programmable Linear DC Power Supply 3 Outputs, 0-30V/0-6A/1.8V/2.5V/3.3V/5V;5A
T3PS30063P
DC Power Supply
Programmable Linear DC Power Supply 3 Outputs, 0-30V/0-6A/1.8V/2.5V/3.3V/5V;5A.
-
Product
High Speed Digital Analog
ITA
The Automatic Test Equipment is designed to provide R&D and the Production floor with a high quality, reliable and easy to use Test Station comprised of COTS equipment from industry leading instrument manufactures. The measurement switching has low thermal offset allowing for micro volt measurements. The switching also accommodates both stimulus and measurement up to 5 Amps. Also to provide High Speed and Static Digital Stimulus and Response that covers LVDS, 3.3V, TTL, CMOS and Industrial logic families. For Serial communications there are SPI, I2C, RS232/485, USB and Ethernet. The system has nine programmable DC power supplies that are capable of powering both the UUT and the UUT interface separately. The system can interface with a variety of UUT’s via an ITA. Each system comes with the Imperial Test Executive, National Instruments TestStand, CVI, LabView and .NET Runtime.
-
Product
Power Supplies
CF - SERIES
-
The CF-series power supply is built with high-quality components for extra long life and maximum system performance along with heavy duty transformers supporting high-end systems. This fanless power supply has a built-in EMI filter for a true no-noise design. The aluminum chassis is built for maximum heat relief to keep the system cool. Combined with a great ventilated structure, you’ll never need a fan. This is a true silent structure that powers your system at 480 watts efficiency.
-
Product
Programmable 70W Electronic Load
MightyWatt R3
-
The All-New MightyWatt revision 3 turns your Arduino Uno R3 or Arduino Zero (M0/M0 Pro) into an electronic load capable of dissipating 70 Watts in a very small form factor. Ideal for testing power supplies, batteries, solar cells, fuel cells or power amplifiers. MightyWatt R3 has a research-grade electronics and is aimed not only at hobbyists but also at professionals.
-
Product
TWT Amplifiers
-
dB Control designs and manufactures high-power microwave amplifiers, transmitters, high- and low-voltage power supplies and modulators for radar, electronic warfare (EW), electronic countermeasures (ECM) and data link applications. The modularity of our designs enables us to rapidly configure power products for custom applications. Our products can meet your specifications and platforms requirements for ground-based, shipborne and high-altitude military manned and unmanned aircraft.
-
Product
Franklin Tester Model
Model FT2
-
Franklin Tester Model FT-2 is designed as per IS:649 & ASTM:717 Standard to measure insulation resistivity of electrical steel sheet. It requires precision & noise free DC regulated power supply and equally distributed pressure on electrode. Franklin Tester FT-2 regulated power supply provides 0.5000V with 0.1% accuracy over load and no load. Most of national and international standard has specified only 0.5%, means FT-2 is equipped with five time better accuracy than required.
-
Product
1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-E® x4, 6 PCI™ Slots Backplane
EBP-9E2
Backplane
- Segment: 1- Slots: 1 PICMG® CPU, 1 PCI-E® x16, 1 PCI-E® x4, 6 PCI™- Support ATX power supplies- Dimension: 328 mm x 206 mm
-
Product
600-Watt DC/DC Converter, 6U VME/cPCI
55U91-01
DC Converter
NAI’s 55U91-01 is a 600 Watt DC/DC Converter that plugs directly into two card slots in a standard 6U VME chassis. It is conduction-cooled through the card edge/wedgelock. This switching power supply accepts +28 VDC input, provides up to 9 outputs at up to 614 Watts, and addresses the power supply needs of both VME and cPCI systems.
-
-
Product
Powered VME Crates
6U VME 195 Mini
-
The VME195 mini crate is the perfect choice for small setups with only a few VME modules. The crate offers 9 VME slots in a compact designed chassis with integrated low noise power supply and cooling fan. The mini crate can be used on the desk either as a desktop or up-right unit or be installed in a 19” rack.
-
Product
Bidirectional Power Supply Device with Regeneration Capability
KP Series
-
KP series is the sophisticated bidirectional power supply device with the regeneration capability*, optimal for evaluating not only in-car inverters for hybrid and electric vehicles but motors, generators, high-capacity vehicle batteries and capacitors as well as wind or solar power generation. We make available the extensive lineup ranging from 2kW to 120kW so you can choose the optimal model according to various applications including development and production.
-
Product
DC System Power Supply, 8 V, 90 A, 720 W
N5742A
Power Supply
The single output, 720 W N5742A provides universal AC input, GPIB, LAN, USB, LXI compliance, and analog/resistance control of output voltage and current
-
Product
4U 5-Slot CompactPCI® Chassis with Redundant Power Supplies
cPCIS-6400U Series
Chassis
The cPCIS-6400U/6400X Series subsystems are designed for 6U cPCI boards with 80mm RTMs. The chassis is 4U in height and standard 19" rack mount width.
-
Product
Cable Fault Locators
-
Cable Fault Locator is a device used for short circuit faults, cable cuts, resistive faults, intermittent faults, and sheath faults. Fiberinthebox supply cable fault locator for power cable, optical fiberal cable, etc. Fault Location in Power Cable is designed to locate cable faults, pinpointing the fault location, route tracing, cable identification, voltage withstand test and cable information management. It can locate all kinds of cable faults for all voltage level cables, including open circuit, short circuit, low insulation, high insulation and flashover faults, etc. Most power cables were buried underground, invisible, and out of reach, with modern new power cable fault locater, it can find the fault point quickly, solve problems immediately and restore power supply.
-
Product
3U CompactPCI Enclosures & Systems
-
3-4U chassis for 3U CompactPCI boards, most of which are with front/rear panel I/O and redundant power supplies.
-
Product
PC/104 DC/DC Power Supplies
-
Diamond offers a wide selection of rugged, wide-temperature, PC/104-sized DC/DC power supplies offering options of up to 218W output power, multiple output voltages, and fixed and variable voltage inputs.
-
Product
Test System
LB303
-
Computer Gesteuerte Systeme GmbH
The test system features the durable G12 receiver from the Virginia Panel Cooperation for the adapter interface. The LB303 is equipped with a power supply of max. 6 kW and can control up to 2 load boxes (in an external rack).
-
Product
Emergency Power Supply Units (EPSU) (10) 5-20R 1U/0U V/H
EPS-1020-HV
-
EPSU Power (Basic / Surge / Metered / Value) – rack mountable power distribution, 120V, optional surge suppression, and amp meter
-
Product
Power Supply
-
A power supply provides the required power for a test application or additional devices. A constant output voltage is generated from an unstabilized input voltage.There are single-channel or multi-channel models with fixed or programmable output voltage. Other features include programmable current limiting or safety functions such as overvoltage protection (OVP) or overcurrent protection (OCP).
-
Product
Power Analyzers
-
Our line of Digital Power Analyzers offers excellent measurement performance and value for power applicationsAvailable in single channel form or as a four slot mainframe, APS Power Analyzers provide precision power measurements for AC and or DC power measurement requirements. They are a perfect compliment to our AC Source and DC Power Supplies as the offer higher accuracy and resolutions that typically found in T&M power conversion equipment.
-
Product
Power Supply, 300V, 17A, 5100W
N8761A
Power Supply
The Keysight N8761A is a 300V, 17A, 5100W, single output power supply in a small 2U package. It offers flexible AC input options, analog/resistance control of output voltage and current, as well as parallel and series connection of multiple supplies to achieve more output current or voltage respectively.
-
Product
Regenerative Power System, 1500 V, ±60 A, 30 KW, 400/480 VAC
RP7984A
DC Power Supply
The RP7984A regenerative power system is a single output, bi-directional, regenerative DC power supply with highly integrated safety features that protect both your people and your device under test.
-
Product
3 PICMG® CPU, 4 PCI™, 7 ISA Slots Backplane
HPCI-13S4LU
Backplane
- Segment: 1- Slots: 3 PICMG® CPU, 4 PCI™, 7 ISA- Supports AT, ATX power supplies- Dimensions: 314.7 mm x 259 mm
-
Product
ISL911xx Family Of Buck-Boost/Boost Regulators
-
The ISL911xx buck-boost regulator family is capable of working with the ultra-small inductors and capacitors to fit within less than 14mm2 board footprint, making them the ideal 2A switching converter solution for space-constrained mobile devices. The advanced wafer-level CSP package requires only a single inductor and very few external components, which minimizes overall space requirements. The ISL911xx regulators’ 2.5MHz switching frequency further reduces the power supply solution size.
