Bit Error Rate Testers
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received. Also known as: BERT
See Also: BER Testers, BERT
-
product
Water Vapor Permeability Tester
QT-WVP
Qualitest Water Vapor Permeability Tester QT-WVP series is used to test the water vapor transmission rate (WVTR) of packaging materials.
-
product
Hipot Line Testers
The newest product of our Hipot Line Testers, the UL Listed HT-S series hipot now comes with an adjustable ground continuity test in range of 0.08 - 1.50 , and Auto-offset for test leads up to 1.00 . Performs 0-2000 AC Hipot Test. Neutral/Hot to Ground Leakage current test up to 20 mA AC. Easy to use and connect. Ships complete with cables, manual, and a Calibration Certificate.
-
product
Rebar Corrosion Rate Determination System
Gecor 6
Measures the rate of corrosion and other parameters of rebars. The Gecor 6 utilizes the polarization resistance technique to establish the corrosion rate. This is a quantitative measure of the amount of steel oxidizing at the time of measurement. Up to 100 readings can be stored in memory for later uploading to a Personal Computer.
-
product
Ethernet/LXI hybridNETBOX 14 Bit Digitizer and 16 Bit AWG - 500 MS/s Digitizer on 2 Channels, 1.25 GS/s AWG on 2 Channels
DN2.825-02
The hybridNETBOX DN2.82x series internally consists of a Digitizer and an AWG that can run together or independently. That allows simultaneous data generation and data acquisition for stimulus-response tests, ATE applications, MIMO applications or closed-loop applications. Used independently, the digitizer can acquire test data in the field and the AWG can replay this test data in lab. The hybridNETBOX offers 14/16 bit resolution and is available with digitizer sampling rates of up to 500 MS/s and AWG sampling rates of up to 1.25 GS/s. The hybridNETBOX can be installed anywhere in the company LAN and can be remotely controlled from a host PC.
-
product
Cable Tester & Cable Tracer & Multi-Functions Lan Tester
M-CT-430A
Fuzhou Metricu Technology Co Ltd
The multifunction LAN tester M-CT-430A is designed for maintenance and installation of cable, cable tracer, and HD Coaxial video level meter test in one equipment. The unit supports detect the near-end, mid-end and far-end fault point of RJ45 cable connector, and also supports Port Flash, PING test, IP address Scan, Link Monitor. Installers take the all in one cable tester, making working conditions safer and increasing productivity.
-
product
pH/REDOX, Conductivity, Oxygen, Chlorine, Turbidity Testers
Lutron Electronic Enterprise Co., Ltd.
Your product description goes here.
-
product
Earth Resistance Tester
G-TEST
To check the condition of a grounding connection, an earthresistance tester is used to measure the residual ground voltage,resistance and resistivity (Wenner method).
-
product
Heat Seal Tester
HST-01
Jinan Leading Instruments Co., Ltd.
HST-01Heat Seal Tester seals the specimen to determine the seal parameters of basicfilm, laminated films, coating paper and other heat sealing laminated filmsaccording to the requirement of relative standards. The seal parameters includeheat seal temperature, dwell time, and the pressure of heat seal. Heat sealmaterials that have different melting point, heat stability, fluidness, andthickness of could show various heat seal properties, which cause obviouslydifferent seal technique.
-
product
Avionics Data Bus Tester
CORVUS-300
CORVUS-300 is an all-in-one avionics data bus tester combining Bus Monitoring, Time-Domain Reflectometer and Wire Mapping capabilities. Its modularity allows the addition of a Vector Network Analyzer or a Spectrum Analyzer based on testing requirements. CORVUS-300 is stock-listed, NSN 6625-01-703-0413, and managed by AFSC/PZAAC.
-
product
Shore Hardness Testers
Measures the level of resistance a material demonstrates against indentation pressure.
-
product
Digital (1kV up) H.V. Insulation Testers
7015 IN
Standard Electric Works Co., Ltd
● Protection class: IP66 (Lid closed)● Microprocessor controlled.● 2 Lines x 16 characters, large intelligent LCD module.● 30 insulation test voltages : 500V, 1kV, 1.5kV, 2kV, 2.5kV, 3kV, 3.5kV, 4kV, 4.5kV, 5kV, 5.5kV, 6kV, 6.5kV, 7kV, 7.5kV, 8kV, 8.5kV, 9kV, 9.5kV, 10kV, 10.5kV, 11kV, 11.5kV, 12kV, 12.5kV, 13kV, 13.5kV, 14kV, 14.5kV, 15kV● AC/DC Voltmeter.● PI (Polarization Index) indication.● DAR (Dielectric Absorption ratio) indication.● Auto-ranging on all insulation ranges.● Current measurement.● Backlight function.● Menu driven.● Visual and audible warning if external voltage is present. (≥30Vac or ≥30Vdc)● Short-circuit current up to 5mA● Auto-hold function to freeze the reading.● Overload protection.● Adjustment for testing time (duration) : 1~30 minutes.● Calendar.● Indication memory for data storage.● Optical USB to RS-232 data transmission.● Auto-off.● 200 measurement results can be saved in the memory and recalled on the display.
-
product
Fluorescent Lamp Asymmetric Pulse Tester
UI2002C
UI2002C is designed according to the latest update in IEC 61347-2-3 about the test requirements for local rectifying effects on tubes. It imitates the condition when tube is under local rectifying status and tests the abnormal protection function of ballast by adopting fluorescent lamp asymmetry pulse test method with 3 windows for displaying rectified voltage, rectified current, and rectified power. It is easy for operation and with high test accuracy. • Measure lamp voltage, lamp current , average and total power of lamp. • Lamp voltage range: 10~300V • Lamp current range: 10mA~1.0A • Lamp power range: 0.5~300W • Tolerance is 5%
-
product
Fiber Optical Cable Testers
Encompasses the processes, tools, and standards used to test fiber optic components, fiber links, and deployed fiber networks.
-
-
product
Electric Servomotor Fixed Torsion Tester
This tester series is one of the fastest standardized products among electric servomotors Torsion Fatigue / Durability Tester for various materials and automobile parts .
-
-
product
Transformer On-Load Tap-Changer Tester
HTBYC-4000 / 257
Wuhan Huatian Electric Power Automation Co., Ltd.
Mainly used for measurement transformer with load pick up switch transition waveform, transition time, instantaneous transition resistance value, three-phase synchronism and so on.
-
product
Martindale Abrasion Tester
UI-FT19
Martindale Abrasion Tester is used to test pilling & abrasion resistance of textile fabric, leather and other materials by rub sample in all directions (a Lissajous figure) in wet or dry conditions.
-
product
ADSL / 2 / 2+ Handheld VoIP Tester
QuickTest 500
*Rapid Testing. The QuickTest 500 ADSL2+ Tester's automatic Service Verification Test Suite starts as soon as you switch on (results are typically obtained in less than 3 minutes)*Simple to use. Virtually no product training required with QuickTest 500 ADSL Tester*Configurable Pass / Fail Indicators on the LCD display and clearly presented in multi-colour LEDs on the front panel*No need to get a laptop out*Save and name up to 16 test results at any one time*Line Voltage LED indicates poor, missing or excessive Line Voltage*ADSL/2/2+ Test LEDs to indicate if ADSL Showtime achieved*In Service LED indicates problems with PPP or IP layer*LEDs to indicate problems with the Trained Line Rate, poor Noise Margin or excessive Line Attenuation
-
product
Device Current Waveform Analyzer, 1 GSa/s, 14/16-bit, 4 Channel
CX3324A
The CX3324A is a 4-channel model for engineers and researchers who need more than two channels for current waveform measurements at one time. Using a passive prove interface (CX1151A) with a current sensor (CX1101A, CX1102A, CX1103A) enables power measurements. The bandwidth and the memory depth per channel are option and can be selected from 50 MHz, 100 MHz and 200 MHz, and 16 Mpts, 64 Mpts and 256 Mpts, respectively. Upgrade products for both bandwidth and memory depth options are also available for customers who need more performance after purchasing the product. 8-channel digital channel (CX1152A) can be used with this 4-channel model so that you have more flexibility of triggering.
-
product
64-CH, 12/16-Bit, Up to 3 MS/s Multi-Function PXI Modules
PXI-2200 Series
ADLINIK PXI-2204, PXI-2205, and PXI-2206 are high-density, high-performance multifunction PXI modules. These devices can sample up to 64 AI channels with various gain settings and scan sequences---making them ideal for high-density analog signals with various input ranges and sampling speeds. These devices also offer a differential mode for 32 AI channels to achieve maximum noise elimination. The PXI-2200 series also features analog and digital triggering, 2-CH 12-bit analog outputs with waveform generation capabilities, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timers/counters.
-
product
RCD/LOOP/PAT Testers
Kyoritsu Electrical Instruments Works, Ltd.
Custom microprocessor controlled for highest accuracy and reliability. 3 LEDs for checking correct wiring status. 0 and 180 degree phase angle switch permits quick tests and consistent readings. Digital read-out of tripping time. Constant current source circuitry ensures that a fluctuating mains voltage does not affect the accuracy of readings. Large custom digital display readout. Visual indication of reversed phase and neutral wiring at socket. Designed to IP54 Rating. Complies with IEC 61557 Test of a large kind of RCD''''s: Standard, Selective, AC and A (DC sensitive breakers)
-
product
Automatic Softening Point Tester
LD-LSPT-A10
Automatic softening point testerLD-LSPT-A10is a bench top microprocessor controlled analytical unit that determines the softening point of two samples at once. Operated via touch panel it uses ball and ring apparatus for reliable detection. Designed as per Test methods of Bitumen and Bituminous Mixture for Highway Engineering and ASTM D36 Standard test method for Softening of Bitumen (Ring-and-Ball Apparatus) it is ideal for determining the softening points of petroleum asphalts, coal pitch, liquid petroleum asphalt, etc.
-
product
2 Channel 10 bit 4GS/s Digitizer
VX1761
The VX1761 comes in a VME64X form factor with 2 input channels. The communication to and from the board is provided through VMEBus and Optical Link interfaces.
-
product
Flexural Damage Tester
DRK242A-II
Shandong Drick Instruments Co., Ltd.
It is used to test the dynamic anti-torsion and flexural fatigue performance of coated fabrics.
-
product
Automatic Single Yarn Strength Tester
TESTEX Testing Equipment Systems Ltd.
Single Yarn Strength Tester,to determine breaking strength and elongation of single cotton, wool and other yarns up to 50 N. Yarn Strength Tester complies with ASTM D2256, ISO2062, GB/T14344,etc. Please contact us for more information about yarn strength testing methods.
-
product
Digital ELCB Testers
6221 EL-M
Standard Electric Works Co., Ltd
● High contrast OLED display.● Designed for viewing in the dark, for mining industry.● Microprocessor-controlled.● Indicates phase rotation● Indicates phase presence● TEST for disconnection sensitivity● Battery status indicator● Measures Voltage Phase to Earth● Select one of 3 Phase to test ELCB.● Color-coded test leads.● Phase presence indication from as low as 100Vac.● Fused earth leakage tester.● ELCB works 50Vac to 330Vac 50Hz / 60Hz.● Phase rotation and presence does not require battery to indicate.
-
product
SONET / SDH, OTN, Ethernet and multiservice testers
At the core of EXFO’s expertise are next-gen SONET / SDH, OTN, Ethernet and multiservice testers that are designed to take testing to the next level. These instruments address the needs of field technicians seeking ultimate portability and ease-of-use, as well as network managers and systems vendors who require flexible and scalable, future-proof solutions.
-
product
30 AMP Fuse Buddy Testers
FB305M
Can test circuit current up to 30 Amps - an easy way to check fuel pump amperage. Clever design allows for easy connection into fuse sockets. Fuse Buddy ends are molded into the shape of the fuse itself. During testing the fuse is removed and replaced into the Fuse Buddy. This way, the circuit being tested maintains fuse protection. Fuse Buddy stays put & won't fall out of the socket, like test probes do.
-
product
Shorted Turns Tester for Bobbin Wound Coils
Model STT-4
International Electro-Magnetics, Inc.
The STT-4 Shorted Turns Tester offers a quick and easy means to detect shorted turns in bobbin coils. It is a non-stress and non-contact test.
