Test Systems
group of interoperable devices whose integration perform a common test purpose.
See Also: Systems, Equipment, System Integrators, System Test, System Integration
-
Product
Efficient All-In-One Test Solution for Low-Cost IoT Devices
KT RFCT 2400
-
The low price point creates a cost effective means for testing wireless communication units, while generating a favorable cost to performance ratio.The calibrated RF test system has a small footprint, integrating seamlessly into test system infrastructures via a single Ethernet connection. GPIOs control the DUT and peripherals. The test system enables communication interfaces like SPI, I2C, UART and CAN. Simple Go/No-Go tests can be performed in parallel. The KT-RFCT 2400A features a 70 MHz to 6 GHz frequency range and includes non-signaling and signaling connections. Bluetooth signaling standards are supported up to 4.1 as well as BT-LE. WIFI signaling standards supported are a, b, g, n and ac.The KT-RFCT 2400A is the perfect test system for a wide range of applications, such as Bluetooth, Infotainment, Keyless Entry, Tire Pressure Measurement, GPS and WIFI.
-
Product
Tire Rolling Resistance Test System
-
This system measures the rolling resistance of each tire accurately. In addition to the simultaneous measurement of tire loss resistance and rolling resistance coefficient for each drive by mode operation (JC08, WLTC), coasting test, constant acceleration/deceleration test and transient mode test are able to be performed. Furthermore, measurement of driving noise/ vibration of the tire, effect of the tire loss due to the temperature change can be verified by adding options.Conforming the JIS D 4234: 2009 and ISO 28580: 2009.
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 3Ω to 2.97MΩ
40-251-151
-
The 40-251-151 is a programmable resistor module with 1 channel which can be set between 3Ω and 2.97MΩ with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Power-Switching Test System
High Voltage Switching Test System
-
The Accel-RF Power-Switching Test System is capable of measuring reliability under a variety of conditions for switching power applications up to 1kV (off) and 25A (on) at rates up to 1MHz switching frequency, dependent on voltage. By leveraging technology developed for the RF burn-in tray platform with new fast switching measurement techniques, this system can support testing of multiple devices under elevated temperature stimulus in a small physical area, and offers the flexibility to test both soft- and hard-switching applications. The Accel-RF Power-Switching System is the most flexible and accurate power switching platform available.
-
Product
OST-500 Optical Radiation Test System
-
Hangzhou Everfine Photo-E-Info Co., LTD
OST-500 is an optical radiation safety test system with 200-3000 nm wavelength range, refer to IEC/EN 62471/CIE S009, IEC/TR 62778, GB7000.1-2015, GB/T 20145, IEC/EN 60598 Annex P., IEC/EN 60598 Annex P. IEC/EN 60432, IEC/EN 60335, GB/T34075-2017, GB/ T34034-2017 2009/125/EC and other relevant standards. The system is equipped with a precision automatic dual-axis turntable, which can automatically find and obtain the maximum radiation position, and automatically measure the photobiohazard value of various lamps and lamp systems (LED products, ultraviolet lamps, lighting sources and lamps, etc.) at the maximum radiation position, and carry out safety classification.
-
Product
Tone Generator
-
Control and test 2-way radio systems, repeaters, ANI, Paging and more. Activate 2-tone or 5/6-tone pagers. Operate or test EIA tone-remote systems. Record generated signals to a WAV file Accomplish MORE, by carrying LESS hardware in the field. Monitor inputs and outputs with our FREE built-in audio scope and spectrum analyzer. No external hardware required. Output may be fed directly into radio, twisted pair, or service monitor.*
-
Product
MEMS Test System Development
-
olidus Technologies’ can design and build a test system customized for your exact needs, using our own or off the shelf components:Custom MEMS Test Systems. We can integrate and assemble test equipment and handling systems to fit your requirements. Custom MEMS Test Software. We can write custom software for device-specific calibration and testing, interfacing various instruments and handling systems, or create a customized GUI. We can also adapt our standard STI Test Software to work on your hardware system.
-
Product
LTE RRM Test System
T4010S
-
The T4020S LTE RRM tester is the Keysight platform for LTE RRM conformance testing of LTE UEs. T4020S belongs to the Keysight LTE product family and, as the other LTE T4000S test platforms, is based on the T2010A LTE Wireless Communications Test Set.
-
Product
CMK Mechanical Kits
-
Columbia has created a unique mechanical click system using ball bearings and guiding sleeves. The UUT is connected to the spring contact pins that are connected to the testing environment in a completely linear fashion. Connecting the UUT to probes can be approached both from the top and the bottom and, optionally, even from the side. The ergonomic housing provides generous space for additional measuring electronics. The back and bottom of the housing can be adapted to the various test system interfaces.
-
Product
Industrial Automation Solutions
-
LXinstruments FCT systems for industrial electronics assemblies are particularly suited for applications with a large variant diversity for medium volume sizes. They are used for testing utility electronics as well as for drive control and grid management systems. We have also implemented systems for functional test, repair and calibration of decentralized PLC I/O assemblies.Since early failures in the field often lead to enormous costs, we not only provide functional test systems, but also burn-in systems for simultaneous testing of many assemblies in a climate chamber. Due to the modular structure of our software, it is possible to establish a logical separation between the definition of the climatic profile to be executed and the actual test sequence, during which the different electrical tests are processed. Connections to HALT/HASS systems can also be established without problems.
-
Product
Walk-In Solar Spectrum Test Chamber
-
WEIBER walk in Solar Spectrum Test Chambers are one of solutions to be utilized in large scale PV testing program. We offer customized as well as standard multidimensional test program for PV modules in reasonable prices. This system delivers the weathering stress representative of long term outdoor exposure.Our flexible system can be designed according to our test requirements, to suit environmental test conditions like volume, temperature, humidity solar radiation intensity and other measuring instruments. It is also called Walk in Solar Radiation Test Chamber.WEIBER solar test system are recognized for superior solar simulation environmental Testing, evaluating outdoor use product reliability, quality & safety. This technology allows for very high concentrations of UV energy without excessive heating of test samples. Custom mounting and cooling can be added depending upon specific material exposure requirements. MHGs (metal halide global lamps) are used as radiation source. Solar spectrum chamber also known as Walk in Solar Simulation Test Chamber
-
Product
Pneumatic Vertical Shock Test System
KRD11 series
-
KRD11 series pneumatic vertical shock test system is featured with advanced design, high degree of automation and reliability, simple operation and convenient maintenance. The system meets the requirements of both shock and bump test, can perform conventional half-sine wave, post-peak sawtooth wave, trapezoid wave and other waveform shock tests.
-
Product
PXI 10W Programmable Resistor Module, 2-Channel, 1Ω to 62.1Ω
40-253-011
-
The 40-253-011 is a programmable resistor module with 2 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Fully Automatic Eddy Current Crack Test System
ROTO-SCAN
-
Foerster Instruments, Incorporated
The fully automatic crack test system ROTO-SCAN was specially developed for the testing of rings. The mechanical equipment has been developed for the gentlest possible handling of the test pieces and features a compact and low-maintenance design. The test probes seamlessly scan the inner and outer contours of the test pieces, thus ensuring 100 % testing of the rings.
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 2Ω to 52.4kΩ
40-253-033
-
The 40-253-033 is a programmable resistor module with 1 channel which can be set between 2Ω and 54.4kΩ with 1Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PXIe-2748, 3 GHz, 16x1 PXI RF Multiplexer Switch Module
780587-48
-
PXIe, 3 GHz, 16x1 PXI RF Multiplexer Switch Module—The PXIe‑2748 is a PXI RF multiplexer switch module that is ideal for switching RF signals up to 3 GHz in production test applications. The high channel count of the PXIe‑2748 makes it well-suited for test systems that require switching a large number of RF signals, such as switching several devices under test to a single channel on the RF analyzer. It also features onboard relay counting for relay monitoring.
-
Product
PCI Precision Resistor Card 9-Channel, 2Ω To 52.4kΩ
50-297-033
-
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
Product
Digitaler I/O Mit 16 Kanälen
MDS
-
The static driver sensor module (MDS) is used to replace existing TS02 from previous MTS test systems. The possible pin extension allows to replace the systems MTS 200/210 (4 UCB with 4 MDS = 256 pins). A maximum of 1,024 MDS pins can be realized on the current MTS systems. Up to 4 MDS modules can be connected to one UCB (UCB03 or higher).
-
Product
Fuel Hose Assembly Tester - Basic, USAF
9901-10FHT
-
The basic fuel hose assembly tester is utilized by those users who do not require the complete 9201A test system which includes all test adapters and components required by U.S. Air Force PD 89MMI638. The 9901-10FHT however includes the identical test pump, manifold and controls and with larger valves, ports and fittings for increased fluid flow, is designed for the identical mission of testing fuel hose assemblies. Maximum pressure is 1000 psi allowing better control resolution at lower test pressures.
-
Product
PXI Medium Density Switch Matrix Modules
-
Pickering's range of medium density switch matrix modules is a cost-effective solution for applications that require mid-range matrices in the PXI format. Selected modules are supported by our Diagnostic Test Tools, Built-In-Relay-Self-Test (BIRST) and eBIRST Switching System Test Tools, these tools provide a quick and simple way of finding relay failures within LXI, PCI and PXI switch systems.
-
Product
Protocol Test Platform
USB Explorer 350
-
The revolutionary Ellisys USB Explorer 350 (EX350) is a super-compact yet sophisticated and comprehensive protocol test and analysis system for USB 3.1 (Gen1 and Gen2), USB 2.0, and USB Power Delivery 3.0. Full support of USB Type-C (including CC and Vconn) is provided with an adapter and cables.With many innovative and exclusive features, the USB Explorer 350 meets the demands of today’s technology developers by providing unmatched coverage for protocol analysis, traffic generation, and compliance testing for emerging USB technologies.
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 2.5Ω to 773kΩ
40-251-143
-
The 40-251-143 is a programmable resistor module with 1 channel which can be set between 2.5Ω and 773kΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Scienlab Battery Test System — Cell Level
SL1002A
-
Test System with up to 36 Channels.The Keysight SL1002A provides sink and source with 0 to 6 V, 100 to 600 A, 0.6 to 3.6 kW and 36 channels for battery cells.
-
Product
Low Cost / Used Test Systems
-
For the last 30 years, Terotest has offered a range of used and refurbished ATE Systems, along with all associated spares at very competitive prices. From completely configured systems to the smallest replacement parts Terotest holds a comprehensive range for some of the largest ATE manufactures in the world. See below for more details.
-
Product
Optics Testing Systems
SHSInspect
-
SHSInspect instruments are widely used in R&D and production when performance, reliability and efficiency counts most. Based on the state-of-the-art wavefront sensor SHSLab, Optocraft offers measurement modules, turnkey instruments and automated tools for a great variety of applications in the field of optics and optical systems, such as:*objective lens testing*testing of optical elements and windows*surface shape measurement*inline measurement and automation
-
Product
Portable Test System
MT686s
-
Actual value, vector, curve displaypower generationerror measurementMeasurement of harmonics up to the 40thVoltage supply via existing measurement voltage
-
Product
PXI 20Amp 28Volt 4xSPST Automotive Relay
40-180-111
-
Models 40-180/181 are High Power Relay Modules available with 2 SPST, 4 SPST or 2 SPDT contacts. They are capable of switching inductive/capacitive loads up to 40A at 14VDC or 20A at 28VDC.The 40-180/181 High Power Relay Modules are suitable for switching heavy loads or for slaving large external relays, contactors and solenoids. In particular these relay modules are designed for automotive test applications requiring the switching of D.C. voltage at high current. The 28V version is suitable for truck system test applications.
-
Product
Test Benches DC
-
Combined with a power source system e.g. MTS750 this test bench is used as a DC meter test system with 40 test positions.
-
Product
In-Circuit Test Systems
-
Keysight offers leading board test solutions for electronics manufacturers to tackle a wide range of PCBA test access and coverage issues for today's complex printed circuit assemblies.
-
Product
Pump, Hydrostatic Test, 15,000 psi
9901-150L
-
Hydrostatic test pump may be utilized as a standalone unit or combined with any of our reservoirs, safety test chambers, test fittings or other optional equipment to achieve a complete hydrostatic test system. with integral safety test chamber.
