Product

Cantilever Probe Card

-

MPI Probe Card Technology

MPI Probe Card Technology

MPI Cantilever Probe Card is widely applied on gold bump and pad wafer testing for display driver, logic, and memory device. MPI’s cantilever probes are the corresponding answer to the demands of fi­ne pitch, small pad size, high speed, less cleaning, multi-DUT, high pin count, and ultra-low leakage requirements. With outstanding craftsmanship, innovative architecture and proven methodologies based on mechanical and electrical simulation/measurement results, making MPI the top cantilever provider worldwide.

Product

Resistivity Meter of Powder Composites

RM-200

-

R&J Measurement

RM-200 - R&J Measurement

The resistivity meter is fully automated and does not required any adjustments. The measurement is made by using the four-point contact probe on the ring (ø60 x ø50 x 5mm) and rectangular prisms samples (6 x 6 x 60÷80mm). The measurement results are automatically saved in meter memory, what allows user to manage of data. The RM-200 contain series connection which allow the data transmission to PC.

Product

Current Probes

-

Yokogawa Test&Measurement

Yokogawa Test&Measurement

Current probes allow you to measure DC or AC current. Yokogawa's selection of current probes allow measurements ranges up to 500 ARMS and bandwidths up to 100MHz.

Product

Powerful, Fully Integrated Workstation for Emission Microscopy

PEM-1000

-

Korima, Inc.

PEM-1000 - Korima, Inc.

The PEM-1000 emission microscope incorporates the latest technology in real time, high quantum efficiency, mega-pixel CCD detectors in a back-thinned cooled camera. A portable system, the PEM 1000 can interface with all analytical probe stations, ATE (automated test equipment) and bench top configurations for high speed functional testing.

Product

Elevated 1.68 (48.00) - 7.00 (198.00) High Performance Lead Free Probe

LFRE-1H-7

-

ECT

LFRE-1H-7 - ECT

Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02

Product

True RMS Clamp Meter w/ Pipe Clmap Adapter

DL489COMBO

-

UEi Test & Measurement Instruments

DL489COMBO - UEi Test & Measurement Instruments

True RMS Clamp meter and 2 ATTPC3 pipe clamp adapter, 2 ATT29 K-Type temperature probes

Product

Linear Testfixture for Pylon Mass Interconnected Cassette interface (Cassette Not Included) 6 Positions Blocks, UUT 306 x 248 mm

MG-02-01 Pylon Genrad VG series

-

MG Products

MG-02-01 Pylon Genrad VG series - MG Products

FEATURES• Linear click system with ball bearings, using gas springs• 10 mm ESD-proof top cover with aluminium reinforcement bars• Steel base cabinet with detachable aluminium back and bottom panels• Detachable interchangeable case system with an 8 mm spring loaded probe protection cover• Base cabinet fitted with a telescopic guide rail and catchTECHNICAL SPECIFICATIONS• Max. number of probes (2000N) 1300 units• Max. PCB height: 60 mm• Linear travel: 12 mm• Max UUT: 306 x 248 mm (wxd)• Outer dimensions: 470 x 490 x 100 x 170 mm (wxdxh1xh2)• Designed for Mass interconnect changeable cassette• Up to a maximum of 6 interface blocks of 170 signals• All interface blocks can be customized

Product

Fiber optic active antennas / field probes

EFS-105

-

enprobe GmbH

EFS-105 - enprobe GmbH

The EFS-105 is the first in a family of fiber-optic active antennas & E-field probes. The field distortion caused by the probe head is nearly zero due to the exceptionally small probe head and the all-optical signal transmission and power supply. This gives an invaluable advantage for near field measurements and measurements close to metallic parts.

Product

Hotwire Air Speed Transmitters

HD403TS… Series

-

Senseca

HD403TS… Series - Senseca

Range hotwire transmitters with 0-10 V or 4-20 mA output. Directional or omnidirectional probes.

Product

Multi-probe for Ammonium and/or Nitrate

S470

-

Liquid Analytical Resource

S470 - Liquid Analytical Resource

S470 is a complete family of Ion selective electrodes (ISE) probes suitable for monitoring the performance of the ammonium ion (as NH4+ or NH4–N) and nitrate ion (as NO3– or NO3–N) in a liquid matrix.

Product

150 A, 5 MHz Current Probe - AC/DC, 150 A rms, 500 A Peak Pulse, 6 Meter Cable

CP150-6M

-

Teledyne LeCroy

CP150-6M - Teledyne LeCroy

Teledyne LeCroy current probes are available in a variety of models for a wide range of applications. The full range of Teledyne LeCroy current probes includes models with bandwidths up to 100 MHz, peak currents up to 700 A and sensitivities to 1 mA/div. Teledyne LeCroy current probes are often used in applications such as the design and test of switching power supplies, motor drives, electric vehicles, and uninterruptible power supplies.

Product

Straight Wire Porbe Pins

Buckling Beam

-

Prospect Products Inc.

Buckling Beam - Prospect Products Inc.

Straight wire probe pins are a proven solution for various electronics production test environments.

Product

Quick Silicon Discriminator

HS-QSD

-

HenergySolar

HS-QSD - HenergySolar

HS-QSD Quick Silicon Discriminator is specially designed for silicon sorting，it can quickly test the silicon type, heavy-dopedt, and can be widely used in all kinds of silicon sorting, like granular polysilicon material, break semiconduct silicon wafer, chunk material, top and tail material and so on. With the three probes, it could show type and heavy type simultaneously, strongly improved the sorting efficiency.

Product

Temperature and humidity outdoor, indoor probe

T3110

-

COMET SYSTEM, s.r.o.

T3110 - COMET SYSTEM, s.r.o.

Programmable temperature and humidity transmitter is equipped with temperature and relative humidity sensors. Measured values are also converted to other humidity interpretation - dew point temperature, absolute humidity, specific humidity, mixing ratio or specific enthalpy. Degrees Celsius and Fahrenheit are user selectable. Transmitter contains a microprocessor based control circuitry in a durable plastic case with connection terminals and sensors in a filter with stainless steel mesh. Humidity transmitters is equipped with two galvanic isolated 4-20mA outputs. Configuration of outputs and output range are user adjustable. Large dual line LCD for simultaneous display of T+RH or other humidity interpretation is an advantage. Display is possible to switch off. Computerized design ensures temperature compensation of the humidity sensor and fail indication. State-of-the-art capacitive polymer sensor ensures excellent calibration long term stability, inertia against water and condensation. Transmitters are designed for use in non-aggressive environment.

Product

Flying Prober Test

QTOUCH1202C

-

Qmax Test Technologies Pvt. Ltd.

QTOUCH1202C - Qmax Test Technologies Pvt. Ltd.

he Prober Test System is capable of movement in XYZ directions with fixed angle (θ) and dual probe heads (further expandable up to 4 ) . The system has in-built Vision Camera for easy monitoring of probe needle contact.The prober supports automatic fiduciary recognition. The system has built –in linear encoders to achieve higher precision. It also comes with in-built image processing unit with minimum 5 Mega pixel Camera ,tele-centric lens with image processing software, illuminated with LED bar light with controls.The V-I signature test shall be in-built in the Prober system with “ Best fit Curve “ algorithm .Provision for adding various external Test & Measurement instruments like GPIB / USB / PXI Instruments is available.

Product

DC Meters/Rail Meters:

-

Bierer & Associates, Inc

Bierer & Associates, Inc

Digital DC Resistive Voltmeter has a single range of 0 – 2kV. The unit consists of a meter probe, second probe, and connector cable. This unit is designed to measure DC voltage between the negative return rail and overhead positive cantenary conductor used on transit systems. The five position selector switch located on the face, controls OFF, ON, and Test. The OFF positions are for storage and transit. The ON position is for measurements from 0 to 1999 volts with one-volt resolution. The T position tests basic meter functions and the digital display.

Product

Cantilever type Probe Card / C type

CE Series

-

Japan Electronic Materials Corp.

CE Series - Japan Electronic Materials Corp.

*Standard Cantilever Probe Card*Low Contact force*Stable Contact*High accuracy of alignment*Suitable for variety of Devices

Product

High Voltage Differential Probes

-

Teledyne LeCroy

Teledyne LeCroy

High voltage differential probes provide high CMRR over a broad frequency range (up to 400 MHz) to simplify the measurement challenges found in noisy, high common-mode power electronics environments. The probe’s design is easy-to-use and enables safe, precise high voltage floating measurements.

Product

Geo / Cryogenic / NDE Instrumentation

-

Tristan Technologies, Inc

Tristan Technologies, Inc

Tristan designs and fabricates custom magnetometer systems to study the magnetic properties of samples. SQUID systems are extremely sensitive instruments designed to detect small electromagnetic signals. By combining SQUID electronics with various special purpose probes and auxiliary electronics, laboratory systems having a variety of capabilities are made available. - See more at: http://www.tristantech.com/#sthash.JlYDZcjM.dpuf

Product

MPI Fully Automatic Probe Systems

-

MPI Advanced Semiconductor Test

MPI Advanced Semiconductor Test

Addressing the RF and High Power communication devices and discrete passive components production test market requirements, MPI introduced the TS2500 200 mm fully automatic probe system series. The system is based on industry leading production equipment from the Photonics Automation Division and incorporates decades of experience in RF and High Power measurement techniques from the MPI’s Advanced Semiconductor Test  (AST) Division in combination with other AST products such as RF Probes, related calibration technology, and High Power accessories.

Product

Partial discharge measurement with remote wireless reading

PD-LT

-

ndb Technologies Inc.

PD-LT - ndb Technologies Inc.

The PD-LT allows online partial discharge detection on cable accessories such as cable head for safety and maintenance purposes.The PD-LT indicates the intensity of the partial discharges, converting the electrical charge units (pC) into decibels (dB). Thus the reading is kept as a simple intensity level indication, proportional to the probability of a fault's presence in the tested medium voltage accessory.The remote display gives a dB value of the probe's measurement. The dB value will vary along with the discharges indicators on the PD-LT probe. The measurement range is from 0 to 65dB and the display will show ''OL'' if the reading is over 65dB.

Product

TTL/I2C/SPI* Expansion Kit

OP-SB5GL

-

LINEEYE Co., Ltd.

OP-SB5GL - LINEEYE Co., Ltd.

OP-SB5GL is the interface expansion kit that has a port to measure RS-232C(V.24) and a port to measure the TTL / CMOS signal level communications. The port for TTL / CMOS supports the measurement of TTL / CMOS level communications that power supply system is from 1.8V to 5V. It is suitable for monitoring the communications between the LSI and the interface IC on the printed circuit board by directly probing into the lines. It supports the protocol of not only UART and HDLC but also I2C and SPI* on monitoring and simulating.

Product

ResMap or DualMap Manual Load

-

Creative Design Engineering, Inc.

Creative Design Engineering, Inc.

*Type: Table Top*Wafer load: Manual *Wafer size: 2" to 8", 152mm x 152mm*Mini Environment: N/A*Probe Changer: N/A*Aligner: N/A*Size: 12" x 19" x 10"*Range: 1m/ to 10M/*Accuracy: 0.5%*Repeatability: 0.02% *Static Repeatability: 0.1% dynamic