Product

Standard Directional Gyroscopes

4000B-series

-

Sigma Tek, Inc.

4000B-series - Sigma Tek, Inc.

The 4000B is our standard air-driven directional gyro. As the aircraft turns left or right, gears on the sensing unit and dial shaft translate this rotation into rotation of the instrument’s vertical dial. Left turns produce clockwise dial rotation and right turns produce counter-clockwise rotation. The gyro is controlled by a heading selector knob located on the lower left of the instrument. Pressing and turning the knob first disengages the dial shaft and then resets the dial to a new heading, which results in a new course indication. Releasing the selector knob re-engages the dial shaft. The on-course position of the pointer is always at the top of the azimuth circle (0° on the dial with the aircraft headed north).

Product

Frequency Block Converter

FBC

-

Farran Technology Ltd

FBC - Farran Technology Ltd

The FBC-XX-FB is a full band system can be built upon a Keysight N8975A Noise Figure Analyzer (NFA) or X Series Signal Analyzer with option N9069A. This system allows the user to extend the frequency range of the NFA to allow for accurate noise figure measurements to be performed on a device covering Ka, U, V, E, W bands (26.5-170 GHz), when used with an Agilent E8247C signal generator (or equivalent).

Product

European Standard for Remote Reading of Measuring Devices

M-Bus

-

HMS Networks

M-Bus - HMS Networks

M-Bus (Meter-Bus) is a European standard for remote reading of measuring devices. M-Bus is predominantly used in buildings, for example in electricity meters, gas meters, water meters or other types of consumption meters. It is also used for various sensors and actuators.

Product

Impedance Standards and Calibrators

-

MEATEST, s.r.o.

MEATEST, s.r.o.

Impedance Calibrator is to replace countless single value RCL standards with one calibrator that can switch between the standards like a CD changer in your car. The calibrator contains stable and temperature independent resistance standards, partial capacitance standards and partial inductance standards, simulated by RC T-type passive network. Calibration values of both complex parameters of partial standards are displayed on large LCD screen in preselected pairs of parameters as well as voltage, current and frequency readouts from built-in test signal meter. OPEN and SHORT reference positions are available as well.

Product

Frequency Expansion Modules

-

bsw TestSystems & Consulting AG

bsw TestSystems & Consulting AG

Up To 1.5THz For Network Analyzers Modern communication standards, like for instance 5G, place high demands on components (mixers, amplifiers, antennas, etc.), which have to be examined in high frequency bands (millimeter waves); the requirements include: broad frequency coverage, sufficient output power to operate the components under compression, high dynamic range and stability as well as a reduced dynamic content within the spectrum.

Product

Standard Handheld Display

TW-3.0-S

-

Dynamic Load Monitoring Ltd.

TW-3.0-S - Dynamic Load Monitoring Ltd.

The TW-3.0-S Standard Handheld Display is a modern, slimline, multifunctional load monitoring device which is unique to DLM. This innovative design is built with the user in mind. It has a large, high quality LCD screen which is optically bonded removing the need for a back light and improving clarity in bright sunlight. For ease of use each handheld can be given a customisable friendly name made visible on the screen to make instant identification possible. This multi featured high precision unit ensures reliable load readings while also being simple to operate. It can be used in conjunction with any DLM manufactured load cell, just look for the d+ logo on our products.

Product

Universal Frequency Counter LXI, GPIB

53220A

-

Meilhaus Electronic GmbH

53220A - Meilhaus Electronic GmbH

For fast and accurate frequency and time-interval measurements, you need reliable devices in research and development. The Keysight 53220 universal frequency counter meets the requirements for this with its high accuracy, bandwidth and speed. Depending on the application and budget, choose one of the three available models. The connection to the PC is via USB, Ethernet/LXI or via GPIB.

Product

Frequency Reference Sources

-

Holding Informtest

Holding Informtest

Holding Informtest Frequency Reference Sources

Product

Standard 0.62 (18.00) - 4.00 (114.00) High Performance Lead Free Probe

LFRE-1V-4

-

ECT

LFRE-1V-4 - ECT

Current Rating (Amps): 6Average Probe Resistance (mOhm): 10Test Center (mil): 75Test Center (mm): 1.91Full Travel (mil): 250Full Travel (mm): 6.35Recommended Travel (mil): 167Recommended Travel (mm): 4.24Mechanical Life (no of cycles): 500,000Mechanical Life Remark: *Ultra High force products may observe slight decrease in cycle life.Overall Length (mil): 1,300Overall Length (mm): 33.02

Product

Spectral Radiance / Luminance Calibration Standards

-

Gigahertz-Optik GmbH

Gigahertz-Optik GmbH

Standard lamps calibrated in luminance and spectral radiance. Traceable calibrations in the wavelength range from 250 nm to 2500 nm.

Product

Single Phase Reference Standard Meter

-

Signals & Systems India Private Limited

Signals & Systems India Private Limited

The Single Phase Portable Reference Standard (SPRS-1102) from SANDS is a portable meter test equipment that helps to calibrate the error present in the single-phase energy meter i.e. the meter under test (MUT). The SPRS supports both static and electro-mechanical types of meters. It can also be used to compute the voltage, current, energy, phase angle etc of the meter under test. It has an LCD display and an alphanumeric keypad to suit the user. It can be interfaced with the PC for analysis. It has the capability of storing 1000 test results.

Product

450MM 18In Digital Level Bevel Gauge w/ LCD Backlight Screen, Magnets, Level Bubbles, IP54 Standards

DL400

-

Advance Plus Trading Co., Ltd.

DL400 - Advance Plus Trading Co., Ltd.

Model Number: DL400 Key Specifications/Special Features: 450MM 17.7INCH Digital Level with level bubbles, strong magnets,LCD bright backlight display, IP54 standards 1. 450mm 17.7 inch level with 2 bubbles, 450*28*64mm（L*W*H）, net weight: 430g;2. Resolution: 0.05°;3. Horizontal level measuring range: 0 to 360°;4. Accuracy: ±0.3°;5. Measures angle in degrees, IN/FT, mm/m, % slope or pitch;6. Audible tone at level, plump and setting angle;7. Automatic shut-off after 3 minutes;8. Backlight LCD;9. Self checking accuracy;10. Self calibration;11. Hold-function to freeze the measurement;12. Memory recall (9 measurements);13. With strong magnets in the bottom;14. 2pcs high accuracy horizontal & vertical bubbles, clearly to check;15. Operated by DC 3V (2*LR03 AAA 1.5V batteries, not included); 16. IP54 waterproof & dusyproof industrial standard.

Product

Standard Voltage 9 Pin D-Type Connectors for Pickering Products

-

Pickering Interfaces Inc.

Pickering Interfaces Inc.

The connectors below are suitable to use with Pickering cards and modules that utilize a standard voltage 9-pin D-type connector.

Product

Standard Gain Horn Conical Lens antennas

-

ELVA-1

ELVA-1

Elva’s SLHA series of standard gain horn lens antennas cover the frequency range of 18 to 220 GHz in ten waveguide bands. They can be issued with rectangular or circular waveguide. Lens technology significantly allows decreasing mechanical sizes of horns and correcting beam for the best performance. These horns are ideal solution for measurement gain of other antennas, short range radars and radiometers.

Product

Redundant Frequency and Timing Systems

-

Precision Test Systems Ltd.

Precision Test Systems Ltd.

A unique feature of our frequency standards and distribution amplifiers is that the two separate parts of the redundant system are identical and can easily be inter-changed, for maintenance purposes.  What we mean by this is that that we don't have a "Master" unit and a "Slave" unit.  Whatever unit is powered up first becomes the master unit and the other becomes the slave unit.

Product

Conformance Calibration Standard Test Card for ISO/IEC Data Matrix and GS1 DataMatrix Symbol Verifiers

AI-CCS-DM-G Rev A

-

Applied Image, Inc.

AI-CCS-DM-G Rev A - Applied Image, Inc.

This precision 2D barcode Conformance Calibration Standard Test Card is the first 2D test card to provide ALL 12 of the Primary Reference Symbols specified by ISO 15426-2 for barcode verifiers. They are sized from 0.5mm to 0.2mm so that all the symbol sizes specified in Annex A.3.1 can be tested. Symbols 1-4 are GS1 DataMatrix symbols, while symbols 5-12 are ISO/IEC Data Matrix symbols consistent with the ISO/IEC 16022 standard. The card also includes four calibrated reflectance patches.

Product

WR5.1 Frequency Extension Solution, 140-220 GHz with VDI Extender Modules

CobaltFx 140 to 220 GHz

-

Copper Mountain Technologies

CobaltFx 140 to 220 GHz - Copper Mountain Technologies

CobaltFx cost-effective millimeter wave frequency extension system allows you to build a scalable and affordable 5G testing solution.

Product

1202a High Frequency Distribution

-

Precise Time and Frequency, Inc.

Precise Time and Frequency, Inc.

The ptf 1202A High Frequency Distribution amplifier provides high performance frequency references for laboratory or system use requiring distribution at frequencies of 30MHz and above.The ptf 1202A is especially designed to distribute the high frequency input signal to 12 separate outputs, with minimum signal distortion and maximum isolation between individual output signals.