Calibrators
ascertain instrument graduation deviation and rectify to precision known values.
See Also: Calibration, Power Calibration, Display Calibration, Calibration Standards, Calibration Software, Calibration Services, Calibration References
-
product
1.6T Optical Receiver Test Application
N4917DJCA
Offers fully automated stress eye calibration and receiver testing for 800G and 1.6T modules with 100G and 200G / λ optical interfaces.
-
product
Calibration and Repair Services
Additel calibrations provide you with high confidence and low uncertainty for your standards. Our accredited calibration laboratory utilizes primary-level piston gauge systems and high-performance controllers to provide services for the entire Additel product line. In addition, our repair technicians which are ready to help, should you have trouble with the Additel units you own.
-
product
Peel Force Tester
PT-55
V-TEK Peel Force Testers are built to test, confirm, and record proper sealing strength of cover tape to carrier tape. This ensures parts are secure and protected, yet will release at the designated force. The PT-55 Peel Force Tester incorporates new technology and performance features to make set up easy, maintenance minimal, and calibration accurate. The lightweight design can accommodate 8-120mm tape widths and operates at peel speeds of 120mm/min or 300mm/min.
-
product
NI-9226, 8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module
783864-02
8-Channel, 400 S/s Aggregate, 0 Ω to 4000 Ω, PT1000 RTD C Series Temperature Input Module - The NI‑9226 is a resistance temperature detector (RTD) input module. You can configure the NI‑9226 for two sample rate modes: high sample rate or high resolution. The NI‑9226 is compatible with 3‑ and 4‑wire RTD measurements, and it automatically detects the type of RTD (3‑ or 4‑wire) connected to the channel and configures each channel for the appropriate mode. The module provides per-channel current excitation. The NI‑9226 features calibration and includes a channel‑to‑earth ground double isolation barrier for safety, noise immunity, and a high common-mode voltage range.
-
product
Noise Source Family
SNS Series
Works in conjunction with the NFA Series of noise figure analyzers to simplify measurement set-up and improve accuracy and reliability, automatically downloading electronically stored calibration data.
-
product
True RMS Multimeter w/ Temperature and Capacitance
DM393
UEi Test & Measurement Instruments
The DM393 is one of our safest Industrial Duty meters ever made. All inputs, ranges and functions protected to CATIII 1000 Volts. Perfect for HVAC and electrical technicians whose applications require higher accuracy measurements and True RMS precision. Built-in temperature means one less instrument to bring to the job. The DM393 has convenient access to battery and fuses without breaking calibration seals
-
product
Torque Meters
This portable meter is used for bolt torquing, torque wrench calibration, switch or contact closure measurement and other industrial, QC, and materials testing applications.
-
product
600MM 24In Digital Level Bevel Gauge w/ LCD Backlight Screen, Level Bubbles, IP54 Standards
DL406
Advance Plus Trading Co., Ltd.
Model Number: DL406 Key Specifications/Special Features: 600MM 24INCH Digital Level with level bubbles,LCD bright backlight display, IP54 standards 1. 600mm 24 inch level with 2 bubbles, 600*28*64mm（L*W*H）, net weight: 520g;2. Resolution: 0.05°;3. Horizontal level measuring range: 0 to 360°;4. Accuracy: ±0.3°;5. Measures angle in degrees, IN/FT, mm/m, % slope or pitch;6. Audible tone at level, plump and setting angle;7. Automatic shut-off after 3 minutes;8. Backlight LCD;9. Self checking accuracy;10. Self calibration;11. Hold-function to freeze the measurement;12. Memory recall (9 measurements);13.Handshank design, easy to take and use;14. 2pcs high accuracy horizontal & vertical bubbles, clearly to check;15. Operated by DC 3V (2*LR03 AAA 1.5V batteries, not included); 16. IP54 waterproof & dusyproof industrial standard.
-
product
DisplayMate Multimedia with Test Photos Edition
DisplayMate Technologies Corporation
DisplayMate Multimedia with Test Photos Edition is an enhanced version of the standard Multimedia Edition that adds a carefully chosen set of very high quality high resolution photographs for calibrating, testing, evaluating, and tweaking monitors, projectors and HDTVs, automatically scaled to the native resolution of the display. It has everything in the standard Multimedia Edition including all of its 500+ test patterns up through 4100 x 4100 resolution.
-
product
Calibration & Demag.
Model 8515-D
The Model 8515-D is a medium-energy, high voltage, and capacitor discharge type ringing demagnetizer capable of desaturating Ceramic and Rare Earth magnetic materials. The Model 8515-D is easily adapted to a wide range of production and laboratory demagnetizing requirements. A modern solid-state electronic control circuit, coupled with a rugged, heavy-duty discharge SCR and fixture, make this demagnetizer a highly reliable, low maintenance unit. The electronic voltage control circuit prevents the Model 8515-D from being discharged before the preset energy level has been reached, avoiding incomplete magnet desaturation. An easy to read front panel meter monitors the capacitor voltage. The energy storage level can be easily changed in the field. Integral electrical interlock and fail-safe circuitry provide a high degree of operator safety.
-
product
Online pH Controller
LD-LOPC-A10
Online pH ControllerLD-LOPC-A10features 1 to 3 points pH calibration system, and 4 to 20 mA output signal transmitter. The large and clear back light LCD displays Calibration and setup values, temperature values, ATC (automatic temperature compensation) values, high and low limit of measurement. The automatic electrode slope display helps user decide when to replace the sensor.
-
product
Conductivity/TDS/Salinity/Temperature Pen
Ultrapen™ PT1
This portable water analysis instrument is designed to be extremely accurate, fast and simple to use in diverse water quality applications. Advanced features include the ability to select from 3 different solution types that model the characteristics of the most commonly encountered types of water; proprietary temperature compensation and TDS conversion algorithms; highly stable microprocessor-based circuitry; user-intuitive design; and waterproof housing. A true, one-handed instrument, the PT1 is easy to calibrate and easy to use. To take a measurement, you simply press a button then dip the pen in solution. Results display in seconds.
-
product
Light and Energy Meter
Model 656
OAI Model 656 Meter is designed for use with all mask aligners and flood exposure systems. For over 45 years, OAI is a world leader in UV Light & Energy Measurement Instrumentation used for reliable accurate calibrated control of the photolithography processes in the Semiconductor, MEMS, Wafer Packaging and Wafer Bumping Industries.
-
product
Calibration Foils Sets
990
The Elcometer 990 Calibration Foil Sets are ideal for use in the laboratory, on the production line or on site.
-
product
Gas & Flame Detection System
Syntel
Teledyne Gas & Flame Detection
Syntel is an addressable loop system suitable for use in zone 1 and 2 hazardous areas. The complete addressable loo is fault tolerant operating normally with a short or open circuit. Syntel does not have a CPU, so there is no common failure point. It includes a standard OPC interface and can also be supplied by Modbus allowing easy integration with third party systems.Syntel stores alarm and calibration information in distributed non-volatile memory, hence there is no reliance on a centralized system.Syntel is ideal for installations where there is the possibility for future expansion. The system architecture allows very low cost expansion as cable runs to a central location are not needed.
-
product
PHOTRON 6D-MARKER
Traditional 3D measurement techniques require a minimum of two cameras, precisely located through a complex calibration procedure, to produce multiple data streams that must then be crunched to produce precise 3D or 6D data. The new holographic 6D-Marker from Photron, a world leader in high-speed photo instrumentation, provides engineers with the ability to record and plot true 6DOF (six-degree of freedom) coordinate data from a single camera.
-
product
Microprocessor Based Indicator
Strong Anodized NEMA4X-IP56 ALUMINUM 1/8 DIN CASE Compact Design Provides Excitation to Transducers or Sensors Accept DC mV/V, V, mA Signal Proportional Analog Output V or mA Easy to Program using 4 ButtonsFront Panel Shunt Calibration User Programmable High & Low Set Point Standard No-Output or Relay Output Optional 8-Step Output, RS232, or BCD Output Available
-
product
S Sensor
Z-Gard S Sensor
The Z-Gard S Sensor is designed to detect the presence of carbon monoxide, nitrogen dioxide and combustible gases in air. These sensors employ solid state, electrochemical or catalytic sensors which generate a representative output signal proportional to the calibrated operating range.
-
product
ACCUplace Position Grid
AP-P Series
The AP-P is a unique calibration target that is designed to test the position and/or recognition ability of a vision system. The matrix of small scales, precisely positioned in a grid matrix format, makes testing for subject recognition and system positioning simple.The overall target is comprised of a matrix consisting of 6.0mm x 6.0mm square individual components each having a 5.0mm x 5.0mm X & Y Scale with 0.100 divisions. The scale has pitch accuracy of 1μm. The AP-P is available on two standard materials; Chrome on Glass (CG) and Chrome on Opal (OP).
-
product
Frequency Generation
Quartzlock time and frequency generators offer a complete range of cost effective and low noise sources for a variety of applications. These acurate time and frequency generators are used in telecoms, aviation, nautical and precision test and calibration measurement enviroments.
-
product
Ammonia Low Range PRO Photometer
Mi407
The Milwaukee MI407 PRO Photometer features manual zero point calibration and fast operation in a rugged design. The Milwaukee PRO Photometer is ideal for users in aquaculture, environmental, water treatment and conditioning , and lab applications. This meter is also ideal for educators that want their students to learn the basics of water quality analysis to apply in the real world.
-
product
Radar Altimeter Test Set
EA-6061
The EA-6061 Radar Altimeter Test Set is designed to test and calibrate any and all radar altimeter systems regardless of protocol or encryption. The EA6061 provides multiple, programmable delays with front panel and/or remote computer control. It features ultra wide bandwidth, low loss, high isolation, and high dynamic range. Able to simulate altitudes up to 6350 feet, the test set operates from 4 to 5 GHz and offers NIST traceable altitude accuracy up to 2 inches
-
product
Calibrator Module
CAP CAL
The purpose of CAP-CAL is to check the correctness of Tan Delta and Capacitance of TD 5000 and TDX 5000. The calibrator includes an extremely high accuracy high voltage capacitor, which comes with a certificate issued by ISA - Altanova Group lab.
-
product
FTIR Gas Analysers
Protea’s range of Fourier Transform Infrared (FTIR) Gas Analysers allows for the measurement of nearly any gas with one instrument. A FTIR gas analyser collects a full infrared spectrum continuously, allowing for hundreds of gases to be detected and measured at once. Changes are only needed to software calibration files to measure new gases.
-
product
Safety And Environmental Logging Sound Meter System
05NK001
The simple data logging package for running and analysing noise assessments and checking noise levels. Kit comes with either a Class 2 or Class 1 sound meter for workplace safety and environmental noise checks, a calibrator and PC software in a case.
-
product
Material Thickness
The Elcometer range of ultrasonic material thickness gauges has been designed specifically to be easy to use, calibrate, take readings and create inspection reports. With a wide range of measurement modes including: Pulsed Echo (PE), Echo Echo ThruPaint™ (EE) and Velocity Mode (VM), and a wide range of intelligent dual element transducers, the new ultrasonic non destructive thickness gauges can measure the material thickness of virtually any material such as metals, plastics, glass, epoxies and ceramics.
-
product
96-CH 12-Bit 3 MS/s High-Density Analog Input Card
DAQ-2208
- 12-bit A/D and sampling rate up to 3MS/s- 96-CH single-ended or 48-CH differential inputs- 1024-configuration channel-gain queue- Analog and digital trigger- Bus-mastering DMA with scatter-gather technology- Full auto calibration- Multiple cards synchronization- 2-CH 12-bit 1Ms/s analog outputs with waveform generation functionality (DAQ-2204 only
-
product
Field-installation Type MLSS Meter (Four-Wire Transmission)
HU-200SS
HU-200SS connects immersion type MLSS sensor (SS-90) and measures MLSS in activated sludge. A wide range (0-2000mg/L)of SS contents can be measured with excellent reproducibility using the near-infrared radiation transmission method. Any of the calibration curves of MLSS, Clay (inorganic mud) and Kaolin may be used as standard substances of SS. If "MLSS" is selected for an activated sludge treatment tank, "Clay" for the precipitation treatment of construction sludge, or "Kaolin" for white mud, a concentration can be obtained closer to an analyzed value.
-
product
ITO Sheet Resistance Standards (ITOSRS)
Indium Tin Oxide Sheet Resistance Standards (ITOSRS) from VLSI Standards are NIST-traceable products, intended for calibration of both contact and non-contact sheet resistance measurement tools used in the LCD, flat panel and touch-screen markets.
-
product
Multichannel Voltage Output D/A Converters
Analog Devices offers an industry-leading family of multichannel voltage output D/A converters (DACs), covering 8-bit to 16-bit resolutions, from 2-channel up to 40-channel density, and serial SPI or I2C interfaces. This family of precision D/A converters are in demand for applications that require high channel density and a small form factor, such as optical communications, analog output modules, or LED displays. ADI’s multichannel voltage output D/A converters provide features such as the availability of multiple independent output spans, system calibration functions that allow user-programmable offset and gain, or D/A converter increment/decrement functionality, which reduces the need to add external precision gain stages and facilitates the use of this family of D/A converters.
