Comparators
Contrast similar or divergent values.
-
Product
Comparators
-
General-purpose comparators utilizing CMOS process suitable for low voltage, low power consumption, and fast response.
-
Product
Mid-Range Gas Filter Correlation CO2 Analyzer
Model T360M
-
Teledyne Advanced Pollution Instrumentation
The Model T360M CO2 analyzer measures Carbon Dioxide by comparing infrared energy absorbed by a sample to that absorbed by a reference gas according to the Beer-Lambert law. Using a Gas Filter Correlation Wheel, a high-energy IR light source is alternately passed through a CO2 filled chamber and a chamber with no CO2 present. The light path then travels through the sample cell, which has a folded path of 1.28 meters.The energy loss through the sample cell is compared with the reference signal provided by the filter wheel to produce a signal proportional to concentration, with little effect from interfering gases within the sample. This design produces excellent zero and span stability and high signal to noise ratio, allowing excellent performance over a wide concentration range, making this instrument an ideal choice for CO2 reporting requirements associated with dilution CEMS.
-
Product
Preparative High Performance Liquid Chromatography System
ACCQPrep HP150
-
Compared to Flash chromatography, High-Performance Liquid Chromatography (HPLC) operates under a higher pressure and uses columns of a smaller particle size for higher efficiency and increased resolution for purer results.HPLC is divided into analytical and preparative forms. Prep HPLC uses larger particles, meaning less surface area for the stationary phase, a higher flow rate and, generally, less pressure than analytical HPLC. Flash and prep HPLC are both used to purify large sample quantities; in analytical HPLC, the goal is to achieve the highest resolution possible to observe each unique compound in the sample. Explore the ACCQPrep® HP150 from Teledyne LABS to discover why ISCO is known worldwide for Prep HPLC.
-
Product
Pressure Sensor
MLV Series
-
The MLV Series Compensated Sensor is based on All Sensors’ CoBeam2 TM Technology. The device provides a high output signal at a low operating voltage while maintaining comparable output levels to traditional equivalent compensated millivolt sensors operating at higher voltages. 1 inH2O to 150 PSI Pressure Ranges.
-
Product
Voltage Maintenance Program
VoltRef
-
VoltRef provides the power of automation formaintaining statistical control of the volt in yourlaboratory. This program controls a low thermalscanner and voltmeter to compare voltagestandards using the process recommended by NISTand other national laboratories.
-
Product
Wideband EMF Measuring Equipment
-
Measuring equipment for electromagnetic fields (EMF) for demonstrating safety and environmental compatibility. The devices measure the total electric and/or magnetic field strength and automatically compare it with limit values specified by national and international bodies in standards or directives.
-
Product
PCI Express 5.0 Transmitter Electrical Performance Validation and Compliance Software
D9050PCIC
-
Use the PCIe 5.0 Tx compliance software to test, debug and characterize your PCIe Gen5 designs quickly and easily. It automatically configures the oscilloscope for each test and generates an informative HTML report upon test completion. The application compares the results with the specification test limit and includes margin analysis which indicates how closely the device passes or fails each test. With the option InfiniiSim Waveform Transformation Toolset, the software supports integrated de-embedding of the breakout channel of the test fixture.
-
Product
HMV Horizontal Flame Chamber - Motor Vehicles
-
Atlas Material Testing Solutions
Atlas’ HMV chamber determines the comparative burn rates and burn resistance of textiles, plastics and other automotive interior materials.
-
Product
Hydraulic Comparator
-
Huaxin Instrument (Beijing) Co., Ltd
Portable structure, convenient for pressure gauge calibration in the laboratory or workshop, or on site at the measuring point.
-
Product
DR software, for use with CT100 Series TDRs
CT Viewer™
-
CT Viewer™ is a full-featured TDR waveform analysis software package for Microsoft® Windows® XP / Vista PCs that lets you archive, manipulate, analyze, and compare TDR data acquired with CT100 Series Automated Metallic TDRs or any other TDR instrument, now with live internet streaming and remote control of CT100 Series TDRs. CT Viewer™ is included with CT100 Series TDRs. Read on to discover how CT Viewer™ will change the way you test cables.
-
Product
Universal Gauging
-
To improve the quality of your large diameter machined parts, the portable Universal Setting Gauge from Bowers has been developed as an easy to use comparator tool which can be set up next to the gauge being utilised. This Universal Setting Gauge has been designed to improve the ongoing accuracy levels; when setting the master, the spring loaded setting anvil ensures a constant force is maintained thereby giving repeatable setting readings. The Bowers Universal Gauge’s ingenious modular format enables it to be quickly configured to suit almost any measuring challenge.
-
Product
Desktop Type AE Systems
-
Compared to the online remote AE systems, desktop type AE systems are connected to and accessible within the local network, either directly by wires or via wireless local networks. Such desktop type AE detection system is normally use with a computer or laptop on a desk or table on site or near the facility. It is usually conducted and real-time controlled by professionals to accurately locate the AE ‘Hits’ sources and analyse the AE data in full aspects. There are two types of AE systems that can be used as desktop type systems, the SAEU3H multi-channel AE system and the RAEM systems respectively.
-
Product
Accelerometer (Charge Output Type)
NP-2000 Series
-
This sensor converts mechanical vibrations into electric signals in proportion of vibration acceleration.You can choose the one that is ideal for your purpose,conditions,applications etc. from wide variety of selection.Charge amplifier is necessary because it is a charge output type,however, compared to pre-amplifier built-in type, it can be used at higher temperature in general.
-
Product
Corrosion Testing
-
Corrosion testing helps you estimate component service life, compare candidate materials in your service environment, and help screen your materials and their condition.
-
Product
Pulse Pattern Generators
-
The Pulse Master is a Series of Single and Dual Channel Pulse/Waveform Generators that offers a complete array of pulse, standard, arbitrary, sequenced and modulated waveforms with unmatched performance, even compared to instruments designed to generate fewer types of signals.
-
Product
Interference & Compatibility Evaluation System
ICEy
-
Schmid & Partner Engineering AG
ICEy is the most advanced reactive near-field E/H-field scanning system for the analysis of EM interference and compatibility (EMI/EMC) in highly integrated electronics. ICEy is the only system that provides accurate EM measurements traceable to international calibration standards and also allows independent interlaboratory comparability of EMI/EMC measurement results.
-
Product
PNA-X Measurement Receiver for Antenna Test
N5264B
Receiver
A new industry standard for antenna test with 400,000 point per second data acquisition on all five measurement channels Twice as many receivers available compared to any other antenna receiver on the market Replace existing 8530A and 8360 solutions for a system speed improvement that is 10 times faster Built-in 8510/8530A code emulation software provides a drop-in replacement for existing antenna ranges utilizing an 8530A
-
Product
Proprietary LPWAN/SUB-G Wireless I/O Module
-
WISE-4210 utilizse proprietary LPWAN (low-power wide-area network) wireless interface, which provides better connection compared with 2.4G Wi-Fi.
-
Product
Biconic Logarithmic Periodic Antennas
Stacked LPDA
-
The stacked Logarithmic Periodic Dipole Antenna consists of two ordinary Log.-Per. structures. The excellent characteristics (flat gain over a large bandwidth, low SWR) of the ordinary Log.-Per. designs could be maintained using the stacked LP design. The stacked design helps to focus the directional pattern of the H-plane somewhat, resulting in a typical gain improvement of ca. 2-3 dB compared to an ordinary LPDA. This is especially important for immunity testing, where a maximum fieldstrength and a good field uniformity is required. The beamwidth in the E-plane and the H-plane are nearly identical, providing an optimised illumination of the EuT with minimised ground reflection influence. Further the STLP 9128 C has an excellent cross-polar rejection.
-
Product
Transistor-Level Defect Simulator
Tessent DefectSim
-
Tessent DefectSim is a transistor-level defect simulator for analog, mixed-signal (AMS), and non-scan digital circuits. It measures defect coverage and defect tolerance. Tessent DefectSim is perfect for both high-volume and high-reliability ICs. Tessent DefectSim replaces manual test coverage assessment in AMS circuits needed to meet quality standards such as ISO 26262 and provides objective data to guide improvements in DFT. Tessent DefectSim dramatically reduces SPICE simulation time compared to simulating every potential defect.
-
Product
Carbon Sensor Conductivity Meter (Low concentration type)
HE-480C-GC
-
The length of the sensor has been reduced by 50% as compared to existing systems to reduce space requirements. At the same time, the measurement range has been increased tenfold, enabling the system to measure even samples with comparatively high concentrations. Two different types of chemicalresistant glassy carbon sensors can be used, making the system ideal for chemical dilution/recovery management and pure water recycling as well.
-
Product
Adjustable High Frequency Reference Ballast
HCS-109A
-
HCS-109A Adjustable High Frequency Reference Ballast also called High Frequency Current Source. Comparing to IEC Test Method, HCS-109A is an Equivalent Test Method which is economic solution. HCS-109A equipped with Spectrophotometer & Integrating Sphere Test System. It can also measure the photo, color and electricity parameters for high frequency fluorescent lamp.Specifications: • Input voltage: 200V~240V, 50/60Hz • Input Power: 80 W max • Output Current: 130mA~400mA (Adjustable), accuracy: +/- 1% • Output Frequency: 25kHz< +/-2.0% (Adjustable), accuracy: +/- 0.3kHz • Output current total harmonic wave distortion: THD<2.5% (HF current wave)
-
Product
Horizontal Flammability Tester
TF311
-
TESTEX Testing Equipment Systems Ltd.
Horizontal Flammability Tester, to determine the comparative burn rates and burn resistance of textiles, particularly those for automotive interior use. Horizontal flammability tester is safe and easy to operate, Comprises draft free stainless steel cabinet with observation window, sample holder and door mounted burner.
-
Product
Cryogenic Temperature Sensors
Cernox®
-
Cernox® thin film resistance cryogenic temperature sensors offer significant advantages over comparable bulk or thick film resistance sensors. The smaller package size of these thin film sensors makes them useful in a broader range of experimental mounting schemes, and they are also available in chip form. They are easily mounted in packages designed for excellent heat transfer, yielding a characteristic thermal response time much faster than possible, with bulk devices requiring strain-free mounting. Additionally, Cernox sensors have been proven very stable over repeated thermal cycling and under extended exposure to ionizing radiation.
-
Product
ASA100
-
The ASA100 Analog Signature Analyser will assist you in testing, diagnosing and troubleshooting printed circuit boards without powering them (known as ‘power-off testing’).Connected via USB to a compatible PC running our own free software, with the ASA100 you can easily capture, measure and compare known good signatures (from your ‘golden’ board) with signatures from your suspect board.With the ASA100 we set out to bring the incredibly powerful technique of Analog Signature Analysis to engineers and repair shops at a super-affordable price.
-
Product
Standard Gain Horns
-
Standard gain horns can be used to experimentally determine the gain of other antennas by using the substitution method. The standard gain horn and the antenna under test are alternately connected to a well matched detector system in order to compare their relative power levels. The power level difference is then added to the appropriate level of the calibration curve to determine the absolute gain of the antenna under test.View more Standard Gain Horn Antennas
-
Product
Auto Transformers
-
Osborne often recommends Auto Transformers in situations where reducing physical size of the transformer is advantageous. Auto transformers offer size advantages when compared to equivalent isolation transformers. Auto transformers provide lower levels of regulation than the equivalent isolation transformer. Osborne helps our clients accommodate for the loss of regulation while achieving the physical size (and cost) advantages of auto transformers.
-
Product
Full 4-Axis Motion Control Universal PCI Express Card
PCIE-1245
-
Encoder input: 5 MHz for CW/CCW,P/D,AB mode; Pulse output: up to 5 MHzSupports memory buffer (10 K points) for trajectory planningSupports point-to-point, line and E-Gear; Supports hardware emergency inputCircular and helical interpolation (PCIE-1245 only)Position latch up to 10KHz and memory buffer 1K points (PCIE-1245 only)Position compare triggering up to 100 KHz, and memory buffer is up to 100 K points (PCIE-1245 only)1D&2D plane position compensation (PCIE-1245 only)Gantry mode by semi-closed loop pulse train control (PCIE-1245 only)Dynamic PWM output for velocity following (PCIE-1245 only)
-
Product
Decade Capacitance Box
1412-BC
-
The wide capacitance range and high resolution of the GenRad 1412-BC decade capacitance box make it exceptionally useful in both laboratory and test shop. Owing to its fine adjustment of capacitance, it is a convenient variable capacitor to use with an Impedance Comparator. The polystyrene dielectric used in the decade steps is necessary for applications requiring low dielectric absorption and constancy of both capacitance and dissipation factor with frequency.
-
Product
Laser Photometer
8587A
-
The photometer owners asked TSI to develop a modern version of the Laser Photometer 8587 that retains data continuity with the original version. Without data continuity, vast amounts of legacy research would not be directly comparable to new research. The result was the Laser Photometer 8587A.
