-
product
Login Digital Epstein Tester Model
Model EP400
Digital Epstein Tester EP-400 is designed to measure AC magnetic properties of flat rolled magnetic materials at high frequency by using Watt-meter, Ammeter, Voltmeter and Source. Epstein bridge test method is a fundamental method for evaluating the magnetic performance of flat-rolled magnetic materials in either sheared or stress relief annealed condition. This test method is suitable for design, specification acceptance, service evaluation, and research and development.
-
product
Temperature Transmitter
Knick Elektronische Messgeräte GmbH & Co. KG.
Transmitters for platinum temperature sensors and thermocouples in 6 mm housing with calibrated range selection. Functional safety up to SIL 2, SIL 3 redundant to parameterization via interface or intuitively, directly on the device. Universal use with 24 V DC or AC power supply.
-
product
Multifunction Installation Tester
COMBI519
COMBI519 carries out tests on electric systems in compliance with IEC/EN 61557-1 and therefore measurements of continuity of the protection cable, insulation resistance (with calculation of PI and DAR), overall earth resistance, RCDs type B, A and AC tripping time and current, line / fault impedance with calculation of prospective short circuit / fault current, phase sequence and conformity.
-
product
SDIO Wi-Fi Module
SX-SDMAC
This Wi-Fi SDIO module is a low-power, single-stream solution with 802.11a/b/g/n/ac support based on the QCA9377 System-on-Chip from Qualcomm Atheros. This module supports Wave 2 MU-MIMO (Client), which increases the overall WLAN system performance by 3X compared to 11n. The module’s small form factor, rich features, and low power make it perfect for portable devices.
-
product
Industrial Gaussmeter
The industrial gaussmeter IGM11 is used to measure magnetic DC and AC fields. The measurands are flux density in Tesla or Gauss and the field strength in Amps per meter.
-
product
Small/Medium Capacity Type High-Speed Rotation Torque Detector
TH-2000/1000 Series
The TH-1000 series torque detectors employ a new magnetic phase difference method with improving functionality while maintaining the advantages of Ono Sokki's conventional torque detectors. They incorporate high durability and long service life---the biggest features of our torque detectors. The new magnetic phase difference method does not require AC power supply to an auxiliary motor for rotation detection change. TH-1000 series is a standard type torque detector with the rotation speed range up to 6000 r/min. The TH-2000 series is a high-speed rotation type which can be used for torque characteristic test of high-speed rotating motor such as an EV/HEV motor, a centrifuge machine or the like. The characteristic data of the detector can be automatically set up on the TH-5100 torque meter when power is turned on.
-
product
Miniature Instantaneous Relays
CU-G Series
Heavy duty miniature power relays for demanding applications, switching of AC&DC voltages, resistive and/or inductive loads.
-
product
HOTLink module (SAM)
ARINC 818
The HOTLinkTM stand alone module (SAM) is an invaluable tool for HOTLink testing. The SAM can be used as a portable signal converter, splitter, test pattern generator, or continuity tester. The SAM comes standard with an A/C adaptor and is also compatible with A/C 28 VDC.
-
product
AC Hipot Tester /DC Hipot Tester
YD-Series
Chongqing Gold Mechanical & Electrical Equipment Co.,Ltd
YD series HIPOT tester is applied to test the insulation ability of electric power equipments and insulation materials at power frequency high voltage. The insulation test result of the tester is go or not go. Also the YD series HIPOT tester is a universal power source in HV test. The maximum output voltage and capacity could be customized according the requirements of custom.The tester is consists of single HV transformer and main control box. There are two kinds of HV transformer according to the insulation materials of the HV transformer.They are dry HV transformer and oil HV transformer. For the dry HV transformer the insulation material is epoxy resin.For oil HV transformer the insulation material is insulation oil. The dry HV transformer has a smaller size and less weight than oil HV transformer. But the maximum output voltage is less than 100kv for dry HV transformer. The functions of the main control box are voltage output regulation, protection in emergency and voltage/current value indication
-
product
PXI Switches
The PXI general purpose switch modules deliver fast, reliable switching in a variety of configurations. Cycle power to products under test, control indicator and status lights or actuate external power relays and solenoids with independent, single-pole, double-throw (Form C) or single-pole, single-throw (Form A) switches in a single PXI module. Choose between the high-speed, long-life reed relays capable of switching up to 100Vrms with up to 1A and 25W of power, or the higher power armature relays capable of switching up to 250Vrms, with up to 2A and 60W of power. The general purpose line also includes a module that offers the performance you need to switch heavy loads with up to 300W (DC resistive load)/1250W (AC resistive load).
-
product
Universal Timer/Counter for PCI
PCI385
The PCI385 Universal Timer Counter PCI card is an ideal solution for automated test and measurement applications. The PCI385 features two timer/counter inputs. Both inputs have a coaxial connector for the input range of +/- 10 V and high-voltage pins for the input range of +/- 300 V. The coupling of the inputs is either AC or DC. The PCI385 provides 6 measurement functions: frequency, high-time, low-time, period, counter and phase measurements.
-
product
AC Resistance Bridge
SIM921
Stanford Research Systems, Inc.
The SIM921 AC Resistance Bridge is a precision, low-noise instrument designed for cryogenic thermometry applications. With excitation power below 100 aW, thermistors and other resistive samples can be measured at temperatures below 50 mK with negligible self-heating errors
-
product
Research & Industry
XPERT 20
A small focal spot x-ray source provides increased visibility and sharpness of detail. With an X-ray source of up to 25kV and 1.0mA, the XPERT 20 provides images with the highest resolution to locate the smallest detail. Designed for use in the most limited spaces with complete shielding and other radiation safety features, the XPERT 20 is fully compliant with U.S. Federal and State requirements for radiation safety and operates with only a standard AC power source.
-
product
300-Watt AC/DC Power Supply
56RS3
NAI’s 56RS3 is a 300 Watt AC/DC Power Supply that accepts a three-phase, AC input plus a +270 VDC input. This COTS unit provides a single full-power output (300 Watts) at a baseplate temperature of +85° C or a single 350 Watt output at a baseplate temperature of +70° C.
-
product
AC Load Banks
30 kW Series
Mosebach Manufacturing Company
Mosebach’s 30 kW series load banks offers a continuous load at either 480 or 208 volts in a very compact, lightweight, portable design with a 1kW resolution.
-
product
Current Measurement
Measurements International Ltd.
No Stabilization Period, No Power Coefficient, No Temperature Coefficient, DC and AC Operation, 3000 A Max Current DC.
-
product
Digital Multimeter
Metra 16S
It is Analog Digital Multimeter which measures VAC, VDC, VAC+DC, Frequency, mA DC, mA (AC+DC), Resistance, continuity, Diode, Farad, AC current measurement.
-
product
Clamp Meters
TES Electrical Electronic Corp.
Variable Frequency drive measurement. LoZ voltage measurement to drain ghost voltages. Check 3phase sequence. True RMS reading on AC and DC+AC mode. Inrush current measurement. A measurement for HAVAC flam sensors.
-
product
Clamp Meters
oltage DC 600V with basic accuracy ±(0.5%+5d)Voltage AC 600V with basic accuracy ±(0.8%+5d)Current AC 400V with basic accuracy ±(2.50%+6d)Slimline Electric Clamp Meter Resistance 20M ohms with basic accuracy ±(1.0%+4d)Continuity buzzer sound at 300 ohmsDiode test current 0.3mA; Open circuit voltage 1.5VAccessories: test leads, carrying case, 2(AAA) 1.5V batteriesSize:8-1/16"L x 2-3/4"W x 1-1/2"HSlimline Electric Clamp Meter Weight: 7oz.2000 LCD display countsDecimal Point ReadingsDisplay with backlightData holdMax holdAuto power offLow battery indication
-
product
Test Benches
Our range of test benches is designed for accurate measurement, performance validation and quality control of electrical components and systems. They provide standardised and customised AC and DC testing, with variable signal frequencies and waveforms.
-
product
AC Ground Bond Testers
440 Series
The 440 Series provides advanced 4-in-1 test capability in a convenient one-box solution. This new series performs AC Hipot (448 - 500 VA), DC Hipot, Insulation Resistance and 40A AC Ground Bond tests while taking up minimal production line space. The 440 Series is simple and easy-to-use; reducing setup time and increasing production line throughput for your application. With multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Learn about our 5 Year Warranty.
-
product
Arc Ingintion Tester
The product is designed to carry out Arc Ignition Test as per IS/IEC 60947-1 Clause 8.2.1.1.2 (material used for electrical products). The adjustable current source is 230V AC @ 33A. The load is adjusted to get 32.5A at 0.5 power factor. Included on control unit are Digital Voltmeter, Digital Ammeter, Digital Power Factor Meter and Micro Controller based programmable Sequence Timer with LCD display for display & setting. The arrangement is made to mount the test piece with electrodes as per the specification given in the standard.
-
product
Motor Protection Relay
239
The 239 relay is designed to fully protect three phase AC motors against conditions which can cause damage. In addition to motor protection, therelay has features that can protect associated mechanical equipment, give an alarm before damage results from a process malfunction, diagnose problemsafter a fault and allow verification of correct relay operation during routine maintenance.
-
product
Safety Voltage Detector
289 SVD
Standard Electric Works Co., Ltd
● Bright LED visual indication● Audible indication● Mute function● AC voltage detection: 100Vac ~ 69kVac● Frequency range: 50/60Hz● Easy-to-prove method● Self-test function● Power source: 1.5V(AA) alkaline battery × 3● Non-contact detection by proximity● Personal sensor, easy to wear and convenient to use● Can be attached with hot sticks by optional accessory● Lightweight, robust and compact● Easy access to batteries Comply with EN 61326-1
-
product
25-Watt AC/DC Power Supply
Model 56GS1
NAI’s 56GS1 is a 25 Watt AC/DC Power Supply that accepts multiple AC inputs plus a +270 VDC input. This COTS unit provides a single full-power output at a baseplate temperature of +85° C.Standard features include remote error sensing; remote digital (TTL) turn on/off; and protection against transients, overvoltage, overcurrent, and short-circuits. Options such as ESS vibration testing and choice of output voltages are available, and additional options and special units can be ordered.
-
product
Multifunction Metal Detector
Detects metal: Maximum detecting distance approx. 2 inches (50mm) when the metal conduit/pipe diameter is 20mm. Non-contact AC voltage: 70VAC to 600VAC. Can be used as flashlight or torch. With 0° to 270° degree sensor arm. With sound and light feedback. Battery powered : 1 x 9V (6F22 / 6LR61 / 1604). Dimension (LxWxD) mm : 170x31x31. Packaging: Standard PVC Sliding blister card.
-
product
High Voltage Breakdown Tester
Model HV-55
Laxtronics Instruments & Controls Pvt. Ltd
5 Kilo Volt AC, 5 Kilo Volt DC, 30 Milli Ampere, Timer 0 To 100 Seconds, HV Prods, Start-Stop-Trip-Reset Using Single Switch On The Test Prods. Start Function Apply Test Voltage From 0 To Set Voltage Gradually.
-
product
Power Modules
VadaTech offers high density AC or DC input power modules with up to 95% power efficiency in single module and double module variants to accommodate different power needs. We also offer specialty modules such as extended full, block format for specific chassis types.
-
product
High Accuracy Mini Digital Multimeter
HH2109
High Accuracy (Basic Accuracy 0.7%). LCD display 2000 count, 12.8mm figure height. Manual Ranging at your choice (19 Range). Higher Voltage test up to AC 750V and DC 1000V. Higher Current test up to 10A
-
product
Gaussmeter/Teslameter
Model 2100
The Model 2100 Gaussmeter is a fully featured, high-end Gaussmeter with a low cost Gaussmeter price. It is a compact, high accuracy, microprocessor controlled, flux density measuring instrument. The Model 2100 is capable of measuring static (DC), alternating (AC), or pulsed magnetic fields. Twelve measurement ranges allow the operator to configure the meter for maximum resolution and accuracy from 300mG (30 microTesla) to 300 kG (30 Tesla). Selecting primary measurement functions is quick and easy with dedicated front panel function keys. An easy-to-use menu allows access to user defined parameters such as upper and lower magnetic limits and relative magnetic measurements. Remote meter configuration is completely accessible using the built in RS-232 Interface or optional IEEE-488 Interface.
