Microwave Analyzers
Signal analysis of the radio frequency from 300 MHz to 300 GHz.
-
Product
Mid-Range Chemiluminescence NOX-NO2-NO Analyzer
Model N200M
-
Teledyne Advanced Pollution Instrumentation
The Model N200M uses the proven chemiluminescence detection principle, combined with a state-of-the-art modular architecture, and intuitive operating software to provide accurate and dependable measurements of Nitric Oxide (NO), Nitrogen Dioxide (NO2) and total Nitrogen Oxides (NOx) gases for use in extractive type CEM systems.
-
Product
LXI 50Ω Microwave Transfer Switch
60-808-415-001
Microwave Transfer Switch
These LXI (Ethernet-controlled) Microwave Transfer Switches are suitable for routing 50 Ω signals up to 50 GHz. With up to 16 switch banks, they are ideal for constructing complex microwave switching systems for many applications. Connection is by front panel mounted SMA. SMA 2.9 or SMA 2.4 connectors.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP4T, 26.5GHz, 50Ω, SMA,
40-785C-431-TE
Multiplexer Module
The 40-785C-431-TE (PXI) and 42-785C-431-TE (PXIe) are single SP4T 26.5GHz microwave multiplexers with automatic termination of unused signals and remotely mounted relays. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel.
-
Product
Open Source Logic Analyzer
Logic Pirate
-
8 channels 256,000 Samples recording size 20 MHz sampling speed, can potentially be overclocked to 60 MHz No compromise on sample size when combining different speeds or number of channels Simple configurable edge detection triggers on all inputs (simple OR trigger) Configurable ratio of samples from before and after the trigger (rolling sample buffer) 5 V tolerant inputs (LOW-level voltage < 0.8 V, HIGH-level voltage > 2.0 V) About 500 kB/s transfer speed to the PC (256 kSamples take about 0.5 seconds) Data capturing can be stopped from the host software anytime Cross platform host software for Windows, OS X, and Linux DIY-friendly 0603 parts and SOIC packages used on a 2-layer board On board 3.3 V regulator can supply up to 400 mA to an external circuit Tiny 3cm x 3cm PCB Firmware updates via built-in USB bootloader Probe cables and acrylic case available from Seeed Studio Open source PCB (EAGLE) and firmware files
-
Product
Scalar Network Analyzer Extenders
-
A Scalar Network Analyzer is a type of RF network analyzer that is used to measure only the amplitude properties of a DUT (Device Under Test). Unlike a Vector network Analyzer, it does not measure both amplitude and phase of the DUT.
-
Product
PXI/PXIe Microwave Multiplexer, Single SP6T, 3GHz, 50Ω, N-Type
40-785C-561
Multiplexer Module
The 40-785C-561 (PXI) and 42-785C-561 (PXIe) are single SP6T 3GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
Chemiluminescence 03 Analyzer
Model T265
-
Teledyne Advanced Pollution Instrumentation
The Model T265 is the only commercially available US EPA Federal Reference Method for Ambient Ozone Monitoring according to the latest US EPA regulatory rules for O3. The instrument uses Chemilumescence with Nitric Oxide (NO) as a reagent, making is safe, stable, and effective for all applications. The NO-CL method for Ozone has several advantages over the conventional UV absorption technology, including the avoidance of positive and commonly found interferrents such as VOCs, fine particulates, Mercury, turpines, ClO2, and others. If these pollutants are present in the atmosphere, it can cause UV absorption analyzers to give an artificially high Ozone measurement. The innovative T265 combines speed of response, sensitivity and stability of our proven nitrogen oxide analyzer, with a simple user interface, to provide reliable ozone measurements under the harshest conditions.
-
Product
Bus Analyzer, Monitor, Debugger & Programmer
BusPro-I™
-
The BusPro-I has all the power, flexibility, and features you need to monitor and debug the I2C bus circuitry on your board. The BusPro I2C can be used to monitor and log I2C bus traffic in real-time, generate I2C transactions to communicate with peripheral components on the bus, and in-system program I2C compatible EEPROMs.
-
Product
Handheld Digital Spectrum Analyzer,
109990014
-
RF Explorer is a handheld digital spectrum analyzer, a very affordable tool for work in all ISM popular frequency bands. It is based on a highly integrated frequency synthesizer which offers high performance, compact size, low consumption and low cost.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 10-Bank 26.5GHz SMA
60-801-310
Multiplexer Module
The 60-801-310 is a 6-channel, 10-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
Arc/Spark OES Metal Analyzer
SPECTROMAXx
-
SPECTRO Analytical Instruments GmbH
The SPECTROMAXx stationary metal analyzer is used mainly for material testing in foundries and for incoming and outgoing inspections in the metal industry around the world. It determines all of the elements used in the metal industry, including metal analysis of carbon, phosphorous, sulfur and nitrogen. The seventh generation of the SPECTROMAXx arc spark OES metal analyzer comes with drastically reduced operating costs, significantly shorter measuring times and less maintenance requirements while still offering exceptional precision and stability. And when it comes to productivity, the new SPECTROMAXx sets the benchmark.
-
Product
Cable Analyzer
MM-HTDR MediaManifold
-
The Crestron MM-HTDR MediaManifold Cable Analyzer is a portable handheld device used to determine the length and integrity of RG6 cable runs. Using "time domain reflectometry," the MM-HTDR can measure cable lengths up to 1099 feet.
-
Product
LXI Microwave Multiplexer, 50Ω 6-Channel 3-Bank 40GHz SMA-2.9
60-801-403
Multiplexer Module
The 60-801-403 is a 6-channel, 3-bank RF multiplexer suitable for switching 50Ω signals up to 40GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
Power Analyzers
-
An instrument that measures and quantifies the rate of power flow in electrical systems.
-
Product
Power Quality Analyzer
PQM-711
-
PQM-711 power quality analyzer is an advanced product for wide type of measurements, analysis and recording of network parameters 50/60 Hz and the power quality diagnostic according to European standard EN 50160. PQM-711 is an innovative model with a wireless communication Wi-Fi , which allows for automatic pairing with the included tablet, with a large 10" touch screen. Tablet allows full operating of the analyzer, live data preview and the reading and analysis of data stored in the internal memory. With this solution, the PQM-711 is an unique device that combines the advantages of the analyzer with built-in display and typical portable analyzers (known as Black Boxes).With the tablet you can very fast checked the device under test. On the other hand, you can leave the analyzer module for multi-measurements as a typical logger without display. You can very fast diagnose the machine under test using the tablet. On the other hand, you can leave the analyzer module itself for many days measurement as a typical logger without display. PQM-711 has a transient registration with a maximum sampling rate of 10 MHz (rapid changes in voltage) and control signals. The minimum duration of the registered transient is 650 ns.
-
Product
On-Site Oil Analyzer
MicroLab 40
-
MicroLab 40 is designed primarily for fleets operating equipment with hydraulic components or heavy equipment gears and transmissions. This would include off-road mining and construction vehicles as well as over-the-road equipment with hydraulics such as bucket trucks, fire engine ladder trucks or solid waste trucks. The MicroLab 40 is also used in applications for offshore drilling equipment. In addition to the basic oil chemistry and extended elemental analysis provided with the MicroLab 30, the MicroLab 40 model includes a particle counter which provides critical analysis for cleanliness of hydraulic oils and gear oils to determine the health of those oils and mechanical condition of those components.
-
Product
I2C Protocol Analyzer
EasyI2C
-
It's simple to find an I2C-style bus within arm's reach. Every computer, monitor, television and cell phone has it. Most microcontrollers directly support this protocol as well. Even so, the I2C protocol has many subtle nuances that are hard to grasp and easily forgotten. EasyI2C (TM) helps you to figure out exactly what is happening, without having to examine huge waveform trace capture files or set up complex tests.
-
Product
Moisture Analyzer Series
3050
-
The 3050 series of moisture analyzers utilizes AMETEK’s proven, accurate quartz crystal microbalance (QCM) technology. Built-in verification provides operators with increased measurement confidence.
-
Product
EZ-TorQ III Torque Analyzer
-
The EZ-TorQ III makes torque control easier and more available across every aspect of the line from the calibration lab to the assembly station. Highly portable and user friendly, this battery powered torque validation hub can be easily carried around the assembly line to spot check tools as part of a QA program or used at assembly stations for quick and easy torque tool validation and calibration. The new smart phone like touch-screen interface breaks down barriers and ensures quick and easy validation of different ranges as needed.
-
Product
Multi-function Electrical Safety Compliance Analyzer
OMNIA® II Series
-
Our OMNIA II Series is a complete line of multi-function electrical safety compliance analyzers designed to satisfy even the most demanding application requirements. We've included exclusive productivity-enhancing features and the latest in safety technology to make this product line the envy of the industry. With 6 models to choose from, a multi-language menu system and a variety of automation interfaces available, the OMNIA II is ready for global deployment.
-
Product
LXI Microwave Multiplexer, 50Ω 4-Channel 16-Bank 26.5GHz SMA
60-802-316
Multiplexer Module
The 60-802-316 is a 4-channel, 16-bank RF multiplexer suitable for switching 50Ω signals up to 26.5GHz. It is part of Pickering Interfaces’ range of LXI Microwave Multiplexers which are available with bandwidths between 6GHz and 40GHz and support for 4, 8 12 or 16 banks of 4 or 6-channel multiplexers. It is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA or SMA-2.9 connectors.
-
Product
LXI Microwave Multiplexer, SP4T, 5-Bank, 50GHz, 50Ω, SMA-2.4
60-803-605
Multiplexer Module
Our 60-803-605 is a 5 bank SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 50GHz. The 60-803 range is capable of supporting up to 16 banks of 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
LXI Microwave Multiplexer, SP4T, 5-Bank, 26.5GHz, 50Ω, SMA
60-803-305
Multiplexer Module
Our 60-803-305 is a 5 bank terminated SP4T multiplexer and is part of a range of LXI based microwave multiplexers suitable for switching 50 ohm signals up to 26.5GHz. The 60-803 range is capable of supporting up to 14 banks of terminated 4 channel multiplexers it is ideal for constructing complex microwave switching systems for many applications. Connection is by high performance front panel mounted SMA, SMA-2.9, SMA-2.4 or SMA-1.85 connectors.
-
Product
Carbon / Sulfur Analyzer
ELEMENTRAC CS‑r
-
The ELEMENTRAC CS-r analyzer determines the elements carbon and sulfur by combustion of the sample in an oxygen stream and subsequent measurement of the combustion gases CO2, SO2 and H2O in selective infrared measuring cells. A high sample weight of up to 500 mg ensures excellent reproducibility of the elemental analysis results, even for heterogeneous samples.
-
Product
X-ray Fluorescence Sulfur/Chlorine-in-oil Analyzer
MESA-7220V2
-
The MESA-7220V2 measures both sulfur and chlorine in petroleum based products using the Monochromatic Energy Dispersive X-ray Fluorescence (EDXRF) method. A monochromatic X-ray source is used in order to obtain an ultra-low noise background which affords the best detection limits for both sulfur and chlorine.The detector window size was increased to collect more fluorescent X-rays and thus achieve lower level ppm values. This provides excellent, repeatable performance at both low and high concentrations of both elements.By adjusting the angle of the graphite crystal, the excitation beam can be measured to excite sulfur in the sample, increasing sensitivity.
-
Product
LXI Microwave Matrix, 10GHz, Single 3x3 With Loop-Thru
60-750-133-A
Matrix Switch Module
The 60-750-133-A is a single 3x3 10GHz microwave matrix with loop-thru. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection.
-
Product
Kjeldahl Method (Auto Analyzer)
-
Automatic Kjeldahl Analyzer is an automatic, smart device determining nitrogen content based on Kjeldahl method. It can be widely used in food processing, feed production, tobacco, livestock, soil fertility, environmental monitoring, medicine, agriculture, scientific research, teaching, quality control and other fields for the test of nitrogen or protein content with respect of macro and semimicro samples and can also be used for the test of ammonium, volatile fatty acid / alkali, and so on.
-
Product
Serial analyzer
-
The Serial analyzer sink decodes analog data on a serial bus to serial data. It can be used to monitor and analyze RS232, RS485, MIDI, DMX or other compatible serial buses. The serial analyzer can monitor up to eight sources. When these sources are in sync (all sources are of one (combined) instrument), all captured data will be displayed in chronological order.
-
Product
PXI/PXIe Microwave Multiplexer, Dual SP4T, 18GHz, 50Ω, SMA
40-785C-422
Multiplexer Module
The 40-785C-422 (PXI) and 42-785C-422 (PXIe) are dual SP4T 18GHz unterminated microwave multiplexers. The 40/42-785C range of multiplexers are available as single or dual, SP6T or SP4T panel mounted multiplexers with relays mounted on the front panel. The single slot version can support up to three supplied remotely mounted multiplexers.
-
Product
LXI Microwave Matrix, 20GHz, Single 4x4
60-751-144
Matrix Switch Module
The 60-751-144 is a single 4x4 20GHz microwave matrix. It is part of the 60-750/751 range of LXI Microwave Switches controlled through an LXI compliant Ethernet connection. It is available in a variety of configurations and frequencies up to 20GHz (60-751). The matrix is characterized for 50 ohm applications, for 75 ohm versions please consult your local sales representative.
