I²C
A slow Inter-Integrated Circuit bus protocol.
-
product
Low Cost Emulator
EB-XAG49
* Emulates P51XG49 Microcontrollers * Real-Time Operation up to 30MHz * 3.3V or 5V Voltage Operation * Source-Level Debugger for C and Assembler * MS-Windows Debugger Software * Reduced Set of C-Compiler and Assembler * Support for ROMless and ROMed Microcontrollers * 64K of Code Memory * Performance Analyzer * Real-Time and Conditional Breakpoints * 44-pin PLCC Emulation Header and Signal Testpoints * Serially Linked to IBM PC at 115 Kbaud
-
product
Cable Assembly, 50-Pin D-Type, Male to Male, 0.5m HV, Exit Away From Pin 1
40-970-050-0.5m-MM-HV
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assemblies can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Dynamic Vapor Sorption Analyzer
IGAsorp-XT
The IGAsorp-XT is a fully automated water sorption analyzer designed for measurements at temperatures and humidities beyond those available with conventional DVS analyzers. High resolution sorption isotherms are recorded at humidity values from 0.2 %RH or lower, using the unique climate-XT control method. Combined with high temperature water sorption measurements to 300 °C, an integrated pre-heater and completely flexible method programming, the IGAsorp-XT is the world’s most advanced benchtop DVS analyzer.
-
product
Needle Microprobe
MT-D
Fast-response 29 gauge needle surface probe for locating inflammation, arteries, etc. Also for dental use. 1/4'' right angle needle length, 3/4'' needle distance from lead. 5.5'' long handle for ease of use. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Sensor within .3mm of tip. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
product
Cable Assembly, 50-Pin D-Type, Male to Unterminated With Ferrules, 0.5m HV, Exit Away From Pin 1
40-972-050-0.5m-MU-HV
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
CompactRIO Chassis
CompactRIO Chassis can add C Series I/O modules to an EtherCAT-, Ethernet- or MXI-Express-compatible system. You can program the onboard FPGA for inline processing, high-speed I/O, and control. You can also use scan mode to quickly expand your real-time system.
-
product
Torque Metering System
Model TMS2200
Full capability of standard RDT2100 model with the addition of a Class I Division II certification of the system.
-
product
Development System
FE-W7
* Emulates Winbond W77xxx or W78xxx Microcontrollers * 125K Code Memory * Real-Time Emulation * Frequency up to fmax at 1.8V to 5.5V * Wide Supply Voltage Support * MS-Windows Debugger For C And Assembler * Emulation Headers for PLCC, QFP and DIP * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
product
PXI-2570 , 40-Channel, 1 A, SPDT PXI Relay Module
778572-70
40-Channel, 1 A, SPDT PXI Relay Module—The PXI‑2570 is a general-purpose switch module that features independent single‑pole double‑throw (SPDT) Form C armature relays. Each relay channel has a normally closed (NC), normally open (NO), and common (COM) terminal.
-
product
Electric Fatigue Testing Machine
EFT Series
Jinan Testing Equipment IE Corporation
EFT series electric fatigue testing machine is an ideal platform to test a variety of materials and components for the following high demanding tests: Quasi-static test; Reverse-stress mechanical low cycle fatigue loading tests (LCF); High temperature creep, stress-rupture, relaxation tests in load/strain control mode for medium-term or long term period. Mechanical fracture tests like crack growth & toughness tensile/compression test for ceramics in both room- or vacuum-, high- temperatures up to 1200 C conditions etc. Compression test on plate springs or clutch springs etc. It is also widely used to evaluate the mechanical properties of biologic materials, composites, orthopedic fixation devices, prostheses, spinal constructs, stents, dental implants, elastrometric materials, etc. It adopts electric actuator structure with all-elastic, backlash free, central ball-lead screw driving to achieve direct force transmission to the specimen, it is especially a perfect choice for R&D institutes, universities, nuclear power, automotive and aviation, & aerospace sectors from metals, composites, ceramics, springs and component parts.
-
product
Industrial All-In-One Touch Panel PC Based On Intel Atom® X7-E3950 Processor
STC2-AL Series
- Quad-core Intel Atom® x7-E3950 Processor- 10.1”/15.6” 16:9 LCD with LED backlight up to 50,000 hours- With up to 1920 x 1080 resolution- 10-point PCAP touchscreen- IP 65 rating for water and dust protection- Robustness with wide 9-36 DC input and optional -10°C to 50°C- Ease of installation with optional VESA mount- SEMA support and customed I/O and function expansion
-
product
CAT III Digital Multimeter
82600
Measures AC/DC voltage/current up to 600V and 10A, capacitance, diode, duty cycle, frequency, resistance, temperature and transistor. Includes 13 Functions and an operating temperature range between -40° to 1000°C. Features manual or auto shutdown after 15 minutes of inactivity, protection against overload at all ranges, data hold, low battery indicator and warning alarm. Also includes a LED flashlight for low light situations. Rubber outer case adds protection against drops and a stand bracket to hold meter at viewing angle and test probe holding clips.
-
product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Tinned Ends, 0.5m HV, Exit Away From Pin 1
A050DF4-T-HA050
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
RTD Data Logger
RTD Data Logger is the most commonly used sensors for measuring temperatures in various industries. These are positive temperature coefficient resistive sensors and Pt100 is the most commonly used type of RTD sensor which has 100 ohm resistance at 0 C. IM2000 series RTD data loggers offer bridge measurement technique to compensate for effect of wire length. In addition logger has facility to program offset so that the measurements are more accurate.
-
product
Micro Coax, Contact, ITA, RG316
610141101
Primary mating contact 610140101. (May mate with other Receiver contacts, as well.)Mechanical SpecificationsDurability 10,000 cyclesContact Material Center Conductor – BeCuShield – BrassContact Plating 50µ" Au over 100µ" NiContact Termination Center Conductor - SolderShield - CrimpInsulator PTFEMating Force 1.5 lbs max [0.68 kg]Electrical SpecificationsCharacteristic Impedance 50ΩFrequency Range DC – 3 GHzVSWR 1.22 @ 3 GHzInsertion Loss – √f(GHz) x .06 dBDWV 800 V RMSContact Resistance 6 mOhms center/4 mOhms outer Cable Specifications RG316Environmental SpecificationsOperating Temperature -65°C to +125°CVibration MIL-STD 202, Method 204, Test Condition DShock MIL-STD 202, Method 213, Test Condition IInsulation Resistance 2000 MOhms Min.
-
product
Temperature & Humidity Testing
Environment Associates is outfitted with multiple chambers to suit all types of temperature and humidity testing needs, including: table-top, standard-reaching, fixed or portable walk-in chambers, and if needed, drive-in chambers. All Environment Associates test chambers are equipped with separate data-acquisition equipment for temperature and humidity monitoring. Our temperature and humidity chambers can be readily equipped with specialized data acquisition to digitally record chamber conditions and the test article at multiple data points. Many of our temperature and humidity chambers are equipped with high-performance, maximum-size compressors to produce superior ramp rates equal to or greater than 15°C per minute.
-
product
Transformer Oil Gas Analysis
It is necessary to analyze outgas in transformer insulation oil in power plant facilities. Shimadzu offers a System GC compliant with ASTM D 3612 Method B (oil stripper sampling) or ASTM D 3612 Method C (headspace sampling). The Nexis GC-2030TOGAS3 system, equipped with a PDHID, enables the analysis of more trace amounts of permanent gas than conventional systems.
-
product
cRIO-9046, 1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller
786370-01
1.30 GHz Dual-Core CPU, 2 GB DRAM, 4 GB Storage, -40 °C to 70 °C, Kintex-7 70T FPGA, 8-Slot CompactRIO Controller - The cRIO-9046 is a rugged, high-performance, customizable embedded controller that offers Intel Atom dual-core processing, NI-DAQmx support, and an SD card slot for data-logging, embedded monitoring, and control. It includes a Kintex-7 70T FPGA with LabVIEW FPGA Module support for advanced control and coprocessing. The controller provides precise, synchronized timing and deterministic communications using Time Sensitive Networking (TSN), which is ideal for highly distributed measurements. This controller offers several connectivity ports, including Gigabit Ethernet, USB 3.1, USB 2.0, RS232, and RS485 ports. You can use the USB 3.1 ports to add a local human machine interface and program, deploy, and debug software, which simplifies application development.
-
product
DC/AC Inverter 1500 W
ODS-1500-7123-T
DC/AC inverter with 1500 W from Premium | input ranges 16.8 - 30 VDC | output 120 VAC | operates in temperatures from -25 to +70 °C | approved for EN45545-2 fire and smoke | railway version
-
product
50-Watt DC/DC Converter; Single Output
55JS1
NAI’s 55JS1 provides full-power, single output at a baseplate temperature of +100° C.
-
product
Test Kit
Metriso B530
Wolfgang Warmbier GmbH & Co. KG
Test voltage / Test current: 1 mA < I < 1,3 mAHigh ohmic range: DC 10 volts,100 volts and 500 voltsTest range:low ohmic range: 1 to 10 kOhmhigh ohmic range: 1 kOhm to 199 GOhmOperation: Battery operatedProbes:2x Model 870 (weight: 2,27 kg / ø 63,5 mm) with conductive rubber (grey) and extension,1x hand-held probe Model 45
-
product
Walk-In Conditioning Test Chamber
Weiber Walk in Conditioning Test Chamber offers an ideal apparatus for conditioning materials at non-ambient temperatures. Now researchers, engineers, and technicians have a simple and cost effective method to condition samples prior to testing. Laboratory Conditioning Chamber is designed for the conditioning of samples prior to testing, provides conditions from 20% to 98% RH ± 2 and 0°C to 94°C ±0.5°C.Conditioning Test Chambers offers ideal humidity and temperature conditions required for testing the effect of environmental changes on the product. The chamber can be widely used to evaluate the durability of various products. Weiber delivers customized products at the most economical rate and within the limited delivery period.
-
product
Standard 1.59 (40.40) - 7.00 (198.50) High Frequency Probe
CSP-30TS-011
Nominal Impedance (Ohms): 50Current Capacity (Amps) @ 20° C: 1.00Bandwidth @ -1dB (GHz): 35.00Recommended Travel (mil): 67Recommended Travel (mm): 1.70Full Travel (mil): 100Full Travel (mm): 2.54Overall Length (mil): 1,003Overall Length (mm): 25.48Rec. Mounting Hole Size (mil): 213Rec. Mounting Hole Size (mm): 5.40Test Center (mil): 375Test Center (mm): 9.53
-
product
RF Plasma Generators & Amplifiers
100 W to 2400 W 13.56 MHz Analog/Digital, RS-232, USB interfaces Low Harmonic Distortion Automatic and Manual Gain Control High Speed Pulsing (Bursting) controls Compatible with T&C''''s Matching Networks GUI Software (complete PC control) Includes all essential RF power/communication cables and mounting brackets Air cooled (Air & Water 1200 W +) Half rack mount or stand alone versions Ideal for: Industrial, Scientific, and Medical Applications
-
product
Digibridge
1659
The GenRad 1659 Digibridge RLC Tester is an easily programmable, microprocessor-based high performance passive component tester. It automatically identifies the type of component under test and measures in the proper range. The result is simple, precise, unambiguous RLC component testing. The GenRad 1659 RLC Digibridge is an instrument for measuring primary parameters of inductance (L), capacitance (C) and resistance (R) and secondary parameters of dissipation factor (D) and quality factor (Q). GenRad designed this single compact unit with maximum flexibility and operator convenience in mind. The simple front panel design of the Digibridge requires less effort to operate. Digital display and user friendly control allows test parameters and limits to be set easily.
-
product
Wireless Digital Multimeter 6000 count / NCV / SPT / Anti Burn Protection and with free "K" type temperature sensor (-40°C ~ 250°C).
MS-W2036P2T
This is a Palm size, external wireless connectivity Digital Multimeter integrated with 6000 Count, True RMS auto and manual measurement.
-
product
C Series Current Output Module
The C Series Current Output Module features up to eight channels of simultaneous analog output. You can choose between enclosed and non-enclosed modules. Additionally, the C Series Current Output Module has built-in open-loop detection. This detection generates an interrupt in software when an open loop is detected, zeros outputs to ensure safety, and avoids driving actuators at system power-on. The C Series Current Output Module requires an external power supply and includes a channel-to-earth ground double isolation barrier for safety and noise immunity.The C Series Current Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
product
Tool, Locator, TriPaddle, Receiver
910104146
Tool, Locator, TriPaddle, Receiver (only for contact p/n #'s 610110128 Rev C+ and 610110177)
-
product
Digital Infrared Thermometer
IR-710
Shenzhen Calibeur Industries Co., Ltd..
'- Non-Contact Infrared Thermometer With Laser Targeting '- Range: -38° C to +520° C/-36.4° F to +968° F'- Accuracy : < 0°C： ±3% or ± 3°C ≥0°C： ±2% or ±2°C'- Distance spot ratio (D:S) : 8:1'- ℃/℉ exchange,'- Size: 180x80x40mm'- Weight: 120g'- Power: AAA1.5V 2pcs (not included)
-
product
4 Wire Earth Resistance & Resistivity Tester
4235 ER
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● Earth resistivity (ρ) test.● Earth testing at 20Ω, 200Ω, 2kΩ.● Earth voltage measuring : 0-300V AC.● Automatic C spike check.● Automatic P spike check.● 2-Wire test, 3-Wire test, 4-Wire test.● LCM display.● Auto ranging.● Auto power OFF.● Data hold.● 200 measurement results can be saved in the memory and recalled on the display.● Interval between auxiliary earth spikes is 1.0~50.0m.
