Relay Drivers
Control the energized state of relays.
-
Product
Stepper Motor Drivers
-
ST's portfolio of STSPIN stepper motor drivers spans from relatively simple ICs with current control and phase generation to more complex solutions.
-
Product
PICO SIL Reed Relays
Series 111
-
Requires a board area of only 0.15 x 0.4 inches (3.8mm x 10.2mm). Pins on 0.1 inch pitch as 110 & 112. 3 Watts switch in Mu-metal or Plastic package (not illustrated).
-
Product
PXI/PXIe High Density Electro-mechanical Relay Module, 75xSPST, Normally Closed
42-145A-101-NC
Relay
The 40-145A-101-NC (PXI) and 42-145A-101-NC (PXIe) 75xSPST relay module is part of a range of high density switching modules available in Normally Open (SPST & DPST), Changeover (SPDT) and Normally Closed (SPST) configurations. Connections are made via a front panel 200-pin female connector.
-
Product
64 Channel Form A High Power Relay
DP-cPCI-4305
-
DP-cPCI-4305 is a 64-channel 1 Form A, high power relay module. This general purpose relay can be used for high power switching applications. Applications for this module include power routing, automatic test equipment, relay output for soft PLCs and bounce-free switching.
-
Product
Low-Side FET Drivers
-
Renesas' low-side FET drivers are very high-speed matched dual-drivers capable of delivering peak currents into highly capacitive loads and are excellent at driving large capacitive loads with minimal delay and switching times.
-
Product
Stand-alone Three-phase Protection Relay Test Set
-
Weshine Electric Manufacturing Co., Ltd
Universal Auto Low Price 3 Phase Relay Protection Tester, 3 Channels ,40A/450VA Three-Phase Parallel 120A, 3 Channels, Each Channel ±10A/200VA
-
Product
4 Relay Channels, Non-latching
RY1
-
The RY1 module features 4 individual single-pole, user SPDT Form-C (changeover/break-before-make type) relays (channels). Each channel has a common input terminal (C), a normally closed output terminal (N/C), and a normally open (N/O) output terminal. The channel either energizes or de-energizes the relays (close or open) so that the signal provided on (C) may be switched/directed to either the (N/C) or (N/O) terminals.
-
Product
PXI/PXIe Power Relay Module,5 Amp, 50-pin SGMC Connector
40-153-003-HI
Relay
The 40/42-153-003-HI is a PXI/PXIe high density power relay module with 25xSPST switches rated at 5A and includes the hardware interlock option. User connection is via a 50-pin SGMC male connector, hardware interlock is via a 4-pin 00 series socket (mating plug is supplied). The 40/42-153 range is available in 18, 25, 36 or 50 SPST configurations with or without hardware interlock.
-
Product
High-Frequency Signal Relays
-
Panasonic Industrial Devices Sales Company of America
Panasonic offers a variety of Signal Relays that can switch high-frequency signals. These products are ideal for applications including radio frequency switching, test and measurement, communication and more.
-
Product
Analog Meter Relays
-
Hoyt Electrical Instrument Works Inc.
Hoyt Transistorized Contactless Meter Controllers are complete, self-contained, compact instruments. The CMT Series has a variety of styles and sizes to meet your specific application requirements. These precise instruments continuously indicate any electrical variable. They provide reliable control in a single, self-contained unit, or optionally, a panel-mounted meter with remote amplifier and output relays.
-
Product
PXI/PXIe Microwave Relay, Triple SPDT, 2.5 GHz, 75 Ω, 1.6/5.6, Remote Mount, Failsafe
42-780B-753-E
Relay
The 40-780B-753-E (PXI) and 42-780B-753-E (PXIe) are triple failsafe SPDT 2.5 GHz 75 Ω unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67 GHz in 50 Ω or 2.5 GHz in 75 Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50 Ω and 1.6/5.6 in 75 Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
PXI/PXIe High Voltage Power Relay Module, 14xSPST With Hardware Interlock
40-323-901-HI
Relay
The 40-323-901 (PXI) and 42-323-901 (PXIe) are 14xSPST relay modules suitable for applications requiring high voltage power switching with high density. They have current handling up to 0.25 A, cold switching up to 9 kVDC/9 kVAC peak and hot switching up to 7.5 kVDC/7.5 kVAC peak.
-
Product
PXI 13 x DPDT Power Relays
40-130-102
Relay
Pickering Interfaces 40-130 DPDT Relay Modules are suitable for applications where ordinary reed relay modules require additional current/voltage capacity. It is available in a choice of 8 and 13 relay versions and has voltage handling up to 220VDC/125VAC and current handling to 2A . Connections are made via a front panel mounted 50 or 78 pin D-Type connector.
-
Product
32 Channel, 1 Form C 2A Relay Switch
DP-cPCI-4509
-
The DP-cPCI-4509 is a 32 channel relay switch module. This module is constructed using 2 Form ‘C’ (DPDT) relays. It provides for 250V DC isolation between channels. Out of the two contacts in each relay, one is used to provide the status of the relay through read back and the other is used for switching purpose. The user can write the command for the selected channels on to the Primary latch of the FPGA section. Readback is available to confirm the selected commands.
-
Product
LED Driver (V4, V5, PWM, 18CH)
SLAMMO
-
When it comes to LED control, bigger IS better and the SLAMMO boasts class-leading capacity of up to 25Amps, 600W @24VDC (up to 450W in IP67 enclosures) / 300W at 12VDC. For constant current LEDs, the SLAMMO P can drive up to 96 luminaires equipped with PWM controlled CC drivers such as the Meanwell LDD series (350mA to 1.6A per LDD)
-
Product
0 Hz/DC to 14 GHz, Single-Pole, Four-Throw MEMS Switch With Integrated Driver
ADGM1304
-
The ADGM1304 is a wideband, single-pole, four-throw (SP4T) switch, fabricated using Analog Devices, Inc., microelectro-mechanical system (MEMS) switch technology. This technology enables a small, wide bandwidth, highly linear, low insertion loss switch that is operational down to 0 Hz/dc, making it an ideal switching solution for a wide range of RF applications. An integrated control chip generates the high voltage necessary to electrostatically actuate the switch via a complementary metal-oxide semiconductor (CMOS)-/low voltage transistor-transistor logic (LVTTL)-compatible parallel interface. All four switches are independently controllable. The ADGM1304 is packaged in a 24-lead, 5 mm × 4 mm × 0.95 mm lead frame chip-scale package (LFCSP).
-
Product
PCI Reed Relay Card, 64xSPST
50-115B-121
Reed Relay
The 50-115B-121 is a 64xSPST PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
Switch Modules - 16 Single Pole Relays Arranged as an 8x2 Matrix
JX16/AB-1
Switch Module
This module has 16 single pole relays arranged as an 8x2 matrix as shown in the figure to the left. The matrix may be operated and wired individually for up to 16 8x2's per chassis, or jumpered to the backplane to form up to a 128x2 matrix. It is available with Type S or M reed relays for high speed, long life application. These modules are usually used for 2 wire testing where high and low meter leads must be switched between any two points. Often used for 2 wire LCR meter measurements, cable testing, or open / short testing in a variety of applications.
-
Product
8-CH Relay Output Module
ND-6063
Data Acquisition Module
- 8-CH relay outputs- Output Type: 8 Form A- Contact Rating: AC: 0.5 A / 125 V; DC: 1 A / 30 V or 0.3 A / 110 V; ON/OFF Interval Time: 3 ms- Breakdown Voltage: 500 VAC (50/60 Hz)
-
Product
Relay Software
-
Megger’s advanced relay testing software is designed to make the complex task of relay testing simpler. Intuitive colour screen graphics with a vast library of digital and electromechanical relay routines from relay manufactures across the world.
-
Product
C Series Relay Output Module
Input/Output Module
The C Series Relay Output Module enables you to switch up to eight signals at 60 V maximum DC switching voltage and up to 250 V of maximum AC switching current. For quick reference, every channel features an LED to indicate the state of that channel. The C Series Relay Output Module allows for direct connection to a wide array of industrial devices such as motors, actuators, and DC devices.The C Series Relay Output Module includes the NI-DAQmx driver and configuration utility that simplify configuration and measurements. NI-DAQmx supports NI programming environments as well as Python, ANSI C, C#.NET, and MathWorks MATLAB® software.
-
Product
Portable Relay Tester
-
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuit and will possibly prevent serious damage to plant or injury to personnel. Apart from checking the protective circuits correctly, it is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay tester.
-
Product
Modular Analog & Digital Systems Solid-state, Digital and Relay Modules
G2T Series
-
Universal Switching Corporation
Our Series G2 product family is a field proven and versatile modular platform for both signal switching and distribution. Numerous digital and analog configurations and modules are available for a cost effective and compact solution.
-
Product
PicoBuck LED Driver
-
The PicoBuck LED Driver is an economical and easy to use driver that will allow you to control and blend three different LEDs on three different channels. By default, each channel is driven at 330mA; that current can be reduced by either presenting an analog voltage or a PWM signal to the board. Version 12 of the board adds a solderable jumper that can be closed to increase the maximum current to 660mA. The new voltage regulator also increased the voltage rating on the various components on the board, allowing it to be used up to the full 36V rating of the AL8860 part.
-
Product
Door Module Drivers
-
ST’s actuator drivers are designed for state-of-the-art automotive door-module applications. Our devices employ a scalable actuator-driving concept, which includes package and software compatibility with the wide variety of door electronics used by the industry.
-
Product
8Power Relay Modbus RS-485 Remote I/O
ADAM-4069
Relay Output Module
8ch power relayProtocols:Modbus RTU,ASCIIWatchdog timer to recover the system
-
Product
PCI Express 16 Reed Relay Output Digital Interface
8003e
-
The 8003e PCI Express digital I/O interface provides 16 Reed relay outputs. The outputs provide high quality, long-life, dry contact switch closures suitable for low-current applications up to 10VA. Reed relays are normally open and close when energized. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
Multi-Output Driver ICs
-
Housing multiple half-bridges and high-side switches on a single IC, our multi-output driver ICs are designed to drive small automotive loads and medium current DC motors as well as providing protected supply lines.
-
Product
Auxiliary Voltage Relays
AVR
-
Type AVR volta acquisition systemscontrol/datage acuated relays are designed for indication alarm of annunciation in elextric utility application. the relays are used for data inputs to supervisory and sequential event recorders
-
Product
General Purpose Low-side MOSFET Drivers
-
Renesas' family of low-side FET drivers are very high-speed matched dual-drivers capable of delivering peak currents of 2.0 amps into highly capacitive loads and excellent at driving large capacitive loads with minimal delay and switching times. The high-speed performance is achieved by means of a proprietary "Turbo-Driver" circuit that speeds up input stages by tapping the wider voltage swing at the output. Improved speed and drive capability are enhanced by matched rise and fall delay times. These matched delays maintain the integrity of input-to-output pulse-widths to reduce timing errors and clock skew problems. This improved performance is accompanied by a 10 fold reduction in supply currents over bipolar drivers, yet without the delay time problems commonly associated with CMOS devices. Dynamic switching losses are minimized with non-overlapped drive techniques.
